Boston Acoustics SPEAKER SYSTEM PRI665 Bedienungsanleitung

PRi665

PRi685

PRi85Sub

Professional In-Ceiling Speaker System

142-002648-D OWNERS MANUAL PRI.i1 1 10/4/07 3:26:37 PM

Speciﬁcations PRi665 PRi685 PRi85Sub

Frequency Response (±3dB) 60Hz–18kHz 55Hz–18kHz 38Hz–150Hz

Audio Input Range 20Hz–20kHz 20Hz–20kHz 20Hz–20kHz

Max Power 90 watts 100 watts 100 watts

Nominal Impedance 8 ohms 8 ohms 4 ohms

Switch Settings none none DirX - To Crossover

(normal full range operation)

Dir - To Woofer

(use for separate Sub Amp only)

Sensitivity (2.83V @ 1M) 88dB 89dB 88dB

Bass Unit 6” (153mm) 8” (204mm) 8” (204mm)

Tweeter 3⁄4” (20mm) soft dome 1” (25mm) soft dome NA

Crossover Frequency 3,600Hz 3,500Hz 130Hz (Except Dir)

Grille Frame Diameter 113⁄8” (289mm) 133⁄4” (350mm) 133⁄4” (350mm)

Mounting Hole Cutout 915⁄16” (253mm) 123⁄8” (314mm) 123⁄8” (314mm)

Mounting Depth (with 1/2” dry wall) 93⁄8” (239mm) 113⁄4” (299mm) 113⁄4” (299mm)

Weight 11 lbs (5.0kg) 19 lbs (8.6kg) 18 lbs (8.2kg)

Maximum Ceiling Height 18’ (5.5m) 22’ (6.7m) 22’ (6.7m)

Description

Thank you for purchasing the PRi series speakers for your audio system. These speakers incorporate high quality

components that produce the famous Boston sound. They are housed in a metal enclosure that makes them

easy to install and meets the stringent requirements of electrical codes throughout the country for plenum rated

enclosures. Such enclosures are often required by building codes in commercial applications and residential

applications such as town homes or condominiums.

The bass drivers in the PRi models have a DCD™ mica-ﬁlled copolymer cone with a butyl rubber surround. An inte-

grated, forward-facing tuned port extends bass response. The soft dome tweeters of the PRi665 and PRi685 have a

pivoting mount. Insulation inside the enclosures helps control resonances and improves room-to-room isolation.

Additional Key Features

• The PRi speakers meet the following agency requirements:

UL1480 Listed

UL2043 Testing Standard

NFPA70

UL94-V0 (all plastic materials)

• Moisture resistant design with rust-resistant hardware.

• All parts are UV resistant.

• Built-in cable clamp with an opening for industry standard conduit clamps.

• 4-pin, 2-piece Molex connector for easy connection and daisy chaining of speaker wires.

• Safety wire attachment tab.

142-002648-D OWNERS MANUAL PRI.i2 2 10/4/07 3:26:38 PM

About Installation

NOTE: This manual assumes the installer possesses skill in the proper use of hand and power tools, knowledge

of local building and ﬁre codes, and a familiarity with the environment behind the wall or ceiling in which the

speakers will be installed.

Read this manual completely before beginning the installation. Have a plan for each step of the entire installa-

tion. If you have any doubts about how to proceed, consult a professional installer. Please keep your manual in a

safe place in case you need to refer to it later.

The grille and frame of the PRi speaker can be painted to match its surroundings. If you plan to paint your

speakers, see the information in the “Painting the PRi Speakers” section at the end of this manual.

WARNING: Always turn off the ampliﬁer or receiver when connecting speakers or any other components to the

system.

Speaker Installation Locations

When selecting installation locations you must take into account both mechanical and acoustical factors. The

pivoting tweeter of the PRi665 and PRi685 helps them produce excellent sound even when they are installed in

less than ideal locations.

The mechanical factors have to do with the structural parts inside

the ceiling. If you are installing the speakers in new construction it is

easy to take this into account. Simply select the installation locations

before the wall board goes up. In retroﬁt installation things are more

complicated. First, you must know the locations of the ceiling rafters

to be sure the installation location is between them. An electronic

stud ﬁnder can help locate the ceiling rafters. You must also know

the depth of the rafters to be sure there is enough room above the

ceiling for the speakers.

The locations of heating outlet ducts and electrical ﬁxtures can help indicate where there may be obstructions in

the ceiling. As a ﬁnal check, before cutting the hole for installation, drill a small hole at the center of the instal-

lation location. Insert a long, bent piece of wire and move it around to conﬁrm that there are no obstructions

behind the chosen location.

Installation in drop ceilings is easy since ceiling tiles can be

removed for access to the installation location. Just be sure

there is adequate room above the ceiling grid to accommo-

date the speakers. See the Mounting Depth speciﬁcations on

the preceding page. Optional drop ceiling support brackets

are available. Their use is described on page 10.

In addition to the area for the installation cutout you must

allow an additional 1” of clearance around it. This ensures that

there is room for the mounting clamps to deploy.

Also remember that you must run speaker wires from the ampliﬁer to the installation location. This is easy

in new construction installations. It is also easy in drop ceiling installations once the wire is in the area

above the ceiling grid. In retroﬁt installations wire routing is more difﬁcult. Be sure to take this into ac-

count when planning your installation.

PRi685 / PRi85Sub PRi665

9 15/16"

229mm

123/8"

314mm

143/8"

365mm

11 15/16"

280mm

142-002648-D OWNERS MANUAL PRI.i3 3 10/4/07 3:26:38 PM

The best installation location from the acoustical performance standpoint depends on what you want

from your system. Typically in-ceiling speakers are used one of two ways: 1. To provide general sound

and music coverage to a room, such as a den, dining room or in a commercial situation. 2. As surround

sound speakers in an A/V system.

Since the speaker installation is permanent and the furniture placement may not be, you should ﬁrst

determine the best long-term location for the speakers—one that will accommodate future relocation of

the furniture, while still providing well-balanced sound to the primary listening area.

For the most balanced sound, place each speaker at an equal distance from the prime listening position.

If you are installing two pairs of speakers in a room you can consider putting the speakers for the two

channels diagonally from each other. This is also true in commercial installations. For the sake of appear-

ance, you might want to align the speakers with the light ﬁxtures and other ceiling details.

Or you could take advantage of the bass sound reinforcement provided by placing a speaker closer to

the juncture of the ceiling and wall. Installing a speaker approximately 18-inches from the ceiling/wall

corner will provide noticeable bass reinforcement. Installing the speaker closer to a corner is not recom-

mended.

The ideal location for speakers used in

Home Theater is easier to establish. Sur-

round speakers should produce very diffuse

sound. In a typical 5.1 surround sound sys-

tem the surround speakers should be placed

far to the sides of, and somewhat behind the

main seating area. The speakers will produce

a more diffuse sound if the pivoting tweet-

ers are angle toward the side and rear walls.

In 7.1 systems the side speakers should be

placed about midway between the front and

surround speakers and about the same dis-

tance apart as the surround speakers.

There is a good deal more ﬂexibility in the

placement of the PRi85Sub. The ear cannot

easily locate the source of deep bass sound.

Install the PRi85Sub anywhere in the general

vicinity of the other speakers. As with the

other models, installing it about 18-inches

from the ceiling/wall corner will provide

some bass reinforcement.

Speaker Wires

After the speaker installation locations have been chosen, you must run wires to the ampliﬁer that drives them.

In addition to the normal speaker wire considerations, the electrical codes in your area may require the use of

special wire that is resistant to exposure called “plenum rated” wire. Check with an electrical safety inspector in

your area to see if such wiring is required.

The gauge of the wire is also important. Typically you should use at least 14 gauge wire. That is good enough for

runs up to 50 feet or so. For runs of more than 50 feet use heavier 12 gauge wire.

5.1 System Surround Speakers

7.1 System Side Channel Speakers

PRi85Sub

142-002648-D OWNERS MANUAL PRI.i4 4 10/4/07 3:26:39 PM

If the wire must be run more than 75 feet a high voltage distribution system is recommended. Such systems

use a special ampliﬁer that has a “70V” (or in some countries, “100V”) output. This allows relatively small gauge

speaker wires to be run over great distances without signal degradation. Speakers used in a high voltage system

require a transformer. Special versions of the PRi series speakers with built-in transformers are available. Contact

a custom audio system installer for more information.

Connecting the Speakers

Unscrew the fasteners on the back of the speaker that hold the wire clamp in place. Open up the clamp and

insert about 2” of wire through the opening. Tighten the clamp screws to secure the wire. Note: If there is a

jacket around the two wire conductors fasten the clamp to the jacketed part of the wire. Remove the jacket from

the part of the wire that extends beyond the clamp.

Separate the two conductors of the wire. Remove about 3⁄8” of insulation from the end of the wire. Insert the

wires into the appropriate terminals on the connector and tighten the screws on the top of the connector to

secure the wire. Be sure there are no loose strands of wire.

Just before the speaker is mounted plug the

connector into the back of the speaker. Set the

wire clamp in place and tighten the fasteners to

secure it. Finally pivot the moveable cover plate

into position and tighten its fastener to hold it

in place.

Speaker Connection Polarity

It is important that all the speakers in a system are hooked up with the same polarity or “in phase.” Instead of

the wire terminals typical of most speakers, the PRi series models are supplied with a Molex plug-in connector

to facilitate installation. Speaker wires are connected to the plug-in connector then, just before installing the

speaker, the Molex connector is plugged in.

This illustration shows the connector on the speaker and the plug-in connector the

speaker wires are attached to. Note the label beside the speaker connector. It shows

the middle two pins on the connectors are “–” and “+”. The outer two pins are

labeled “LOOP +” and “LOOP –”. The “LOOP” connections are connected to the

regular “+” and “–” connections inside the speaker and facilitate connecting multi-

speaker installations. Use the color coding or other marking on the speaker wires

to be sure that the “+” terminal of the ampliﬁer is connected to the “+” terminal of

the speaker, and “–” is connected to “–”, at every connection.

*,Ê-«i>iÀ

iVÌÀ

*Õ}

iVÌÀ

142-002648-D OWNERS MANUAL PRI.i5 5 10/4/07 3:26:40 PM

Multiple Speaker Connections

Sometimes you may want to connect more than one speaker to a given channel of an ampliﬁer. This can be done

with certain limitations. The main concern is that the impedance (or electrical “resistance”), expressed in ohms,

of the combined speaker load must be within a range common ampliﬁers can handle. The following information

describes basic common multi-speaker connection schemes. For the sake of clarity and space the connection

diagrams will show common schematic symbols.

There are two basic connection methods - parallel and series. Examples of parallel connections are shown below.

The connection example on the left shows the wire from the ampliﬁer and the wire for the second speaker con-

nected to the same terminals. The example on the right shows the wires to the second speaker connected to the

“loop” terminals which are connected to the other terminals inside the speaker. This makes connecting the wires to

the terminals easier. But it also means that if the ﬁrst speaker is unplugged for any reason the signal to the second

speaker is cut off. Parallel connections can also be made by connecting wires from both speaker directly to the

ampliﬁer terminals, typically referred to as “home run” connections. This often results in more wire being used

– usually something you want to avoid.

The parallel connection diagrams also show that two 8 ohm speakers produce an impedance of 4 ohms at the

ampliﬁer. Most ampliﬁers can handle a 4 ohm impedance load. Impedance loads lower than 4 ohms can trigger

ampliﬁer protection circuits or, in some cases, cause over heating.

The diagram below shows examples of series connections. Two 8 ohm speakers in series produces a 16 ohm

impedance. This is an easy impedance for an ampliﬁer to handle. However it will result in somewhat lower power

output. The connection method on the left is a modiﬁed “home run” type connection. The example on the right

side is electrically the same and often requires less wire. But it can be a bit more tricky to wire.

NOTE: These types of connections are unusual in that the “–” of one speaker is connected to the “+” of the

other. This may seem odd, but since the signal ﬂows through one speaker to the other this is how it must be

done in order for the speaker to be “in phase”.

nÊÃ

""* ""*

nÊÃ

""* ""*

nÊÃ

""* ""*

nÊÃ

""* ""*

>«wiÀÊÀÊÀiViÛiÀ

£ÈÊÃ £ÈÊÃ

>«wiÀÊÀÊÀiViÛiÀ

{ÊÃ {ÊÃ

nÊÃ

""* ""*

nÊÃ

""* ""*

nÊÃ

""* ""*

nÊÃ

""* ""*

Parallel Connections

Series Connections

142-002648-D OWNERS MANUAL PRI.i6 6 10/4/07 3:26:41 PM

Connecting three speakers to an ampliﬁer channel is generally not recommended. But if it is done it should be

done using a combined series/parallel connection. Two examples of this type of connection are shown below.

The example on the left shows two speaker in series with the third connected in parallel to one of them. The

third speaker could be connected to either of the speakers connected in series. It could also be connected to

main “+” and “–” terminals instead of the “LOOP” connectors. The example on the right shows two speakers in

series with the third connected in parallel at the ampliﬁer terminals - a variation on the “home run” connection.

The connection methods are electrically the same and produce an impedance of about 12 ohms.

For any system installation more complicated than this you should consult a professional installer for advice on

appropriate equipment, and to be sure the system is connected for best performance and reliability.

Installing the Speakers

Once the installation location has been prepared and the speaker has been connected, the installation of the speak-

er is easy. Simply lift the speaker into the installation hole. Use a phillips screw driver to pivot the mounting clamp

arm outward and draw them down against the back of the mounting surface. Then gradually tighten the mounting

clamp screws, alternating among them, until the speaker is ﬁrmly clamped in place. Do not use excessive force when

tightening the mounting clamp screws. Then press the speaker grilles into place to complete the installation.

Listening Levels and Power Handling

The listed power recommendations assume you will operate your system in a way that will not produce distortion.

Even very rugged speakers can be damaged by a relatively low power ampliﬁer if it is producing distortion.

If you hear a harsh, gritty noise, turn down the volume. Prolonged or repeated operation of your speaker with a

distorted signal from the ampliﬁer can cause damage that is not covered by the warranty.

>«wiÀÊÀÊÀiViÛiÀ

£ÓÊÃ £ÓÊÃ

nÊÃ

""* ""*

nÊÃ

""* ""*

nÊÃ

""* ""*

nÊÃ

""* ""*

nÊÃ

""* ""*

nÊÃ

""* ""*

142-002648-D OWNERS MANUAL PRI.i7 7 10/4/07 3:26:42 PM

Additional Information on the PRi85Sub

The PRi85Sub in-ceiling subwoofer has a built-in passive crossover. If the

subwoofer is receiving a full range signal from the electronics set the

switch on the front of the speaker frame to the “DirX” position to use the

internal crossover. If the PRi85Sub is connected to a component that has

an electronic crossover, such as the Boston Acoustics SA1, you will want to

bypass the crossover. In this instance set the switch to the “DIR” position.

NOTE: The DIR position is provided as a way to use an ampliﬁed LFE signal from a receiver and should be lim-

ited to 30Hz to 750Hz – to ensure the product is protected. We do not recommend or warranty this product if this

frequency limitation is not used.

Notes About Commercial Applications

The plenum rated enclosure and safety agency certiﬁed design of the PRi series speakers make them an ideal

choice for commercial installations. In such installations you may need to connect more than three speakers to

each channel of the ampliﬁer.

Several companies make speaker distribution devices and controls that allow you to vary the impedance the

ampliﬁer “sees” from the control/speaker combination. These devices make it possible to install an elaborate

multi-speaker system while keeping the impedance load on the ampliﬁer in a range it can handle and provides

volume controls to balance the output of the speaker to suit the installation.

Removing the Grilles

Should you need to remove the grilles for any reason use a paper clip bent into a small hook or a grille pick.

Slip the hook through one of the holes and pull the grille straight out.

You may need to pull one edge part of the way out them move to the

other edge and gradually work the grille out of the frame.

Painting the PRi Speakers

You can paint the exposed part of the frames and the grilles of your

speakers to match your room. A paint shield is provided to protect the

speakers.

Most paints, especially water based paints, don’t adhere very well to plastic surfaces or surfaces already covered

with glossy paint. So, you will need to apply a primer coat. Use a primer recommended for plastic surfaces. Be

sure it will produce a surface that the paint you are using will bond to. NOTE: Depending on the type of paint

that will be used for the ﬁnal coat you may or may not need to apply primer to the grille.

Remove the grille as described in the preceding section. Put the paint shield over the front of the speaker. Apply

masking tape to all other part that should be protected. Be sure to cover the mounting clamps and the terminal

cover. Be sure the surfaces to be painted are clean and free of dust, lint, etc.

Apply two or more light coats of primer. Let the primer dry thoroughly between coats. You’ll get better results

and reduce the chance of drips or runs using several light coatings. Lighter coats also reduce the chance the

holes in the grilles will become plugged with paint. Let the paint dry completely. Remove the paint shield and

re-insert the grille.

142-002648-D OWNERS MANUAL PRI.i8 8 10/4/07 3:26:43 PM

Optional Ceiling Bracket

Special brackets are available that make it easy to mount the PRi speakers in a suspended ceiling. The bracket

rests on top of the ceiling grid so the weight of the speaker is supported by the grid, not the ceiling panel. The

bracket has a “foldable” design, shown on the left below, that makes it easy to maneuver the bracket through

the mounting hole.

Once the mounting hole is cut in the ceiling panel place the folded bracket through the hole and pivot it into its

normal shape as shown below on the right. Extend the rails so they rest on the ceiling grid. Set the bracket so

the ﬂanges that extend down from the arcs surround the installation hole. Then connect the speaker and clamp it

in place as in a regular installation.

NOTE: When the PRi speakers are installed in suspended ceilings it is strongly recommended that you attach

a security cable to the tab on the back of the speaker and fasten the other end to a strong structural element of

the building.

iÝÌi`>LiÊÀ>Ã

In this illustration the ceiling grid is

shown without the panels.

142-002648-D OWNERS MANUAL PRI.i9 9 10/4/07 3:26:44 PM

Limited Warranty

Boston Acoustics warrants to the original purchaser of our PRi series speakers that they will be free of defects in

materials and workmanship for a period of 5 years from the date of purchase.

Your responsibilities are to install and use them according to the instructions supplied, to provide safe and se-

cure transportation to an authorized Boston Acoustics service representative, and to present proof of purchase in

the form of your sales slip when requesting service.

Excluded from this warranty is damage that results from abuse, misuse, improper installation, accidents, ship-

ping, or repairs/modiﬁcations by anyone other than an authorized Boston Acoustics service representative.

This warranty is limited to the Boston Acoustics product and does not cover damage to any associated equip-

ment. This warranty does not cover the cost of removal or reinstallation. This warranty is void if the serial number

has been removed or defaced. This warranty gives you speciﬁc legal rights, and you may also have other rights

which vary from state to state.

If Service Seems Necessary

First, contact the dealer from whom you purchased the product. If that is not possible, write to:

Boston Acoustics, Inc.

300 Jubilee Drive

Peabody, MA 01960 USA

Or contact us via e-mail at:

[email protected]

We will promptly advise you of what action to take. If it is necessary to return your PRi series unit to the fac-

tory, please ship it prepaid. After it has been repaired, we will return it freight prepaid in the United States and

Canada.

This symbol found on the product indicates that the product must not be disposed of with

household waste. Instead, it may be placed in a separate collection facility for electronic waste or

returned to a retailer when purchasing similar product. The producer paid to recycle this product.

Doing this contributes to reuse and recycling, minimizes adverse effects on the environment and

human health and avoids any ﬁnes for incorrect disposal.

300 Jubilee Drive

Peabody, MA 01960 USA

978.538.5000

www.bostonacoustics.com

DCD is a trademark and Boston, Boston Acoustics, and the Boston

Acoustics logo are registered trademarks of Boston Acoustics, Inc.

Speciﬁcations are subject to change without notice.

142-002648-D OWNERS MANUAL PRI.i10 10 10/4/07 3:26:44 PM

Andere Handbücher für SPEAKER SYSTEM PRI665

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Boston Acoustics Sprecher Handbücher

Boston Acoustics

Boston Acoustics Lynnfield VR940 Bedienungsanleitung

Boston Acoustics

Boston Acoustics MC200Air Bedienungsanleitung

Boston Acoustics

Boston Acoustics Reflection Series RS223 Bedienungsanleitung

Boston Acoustics

Boston Acoustics BA Classic 8 Bedienungsanleitung

Boston Acoustics

Boston Acoustics 351 361 381 Bedienungsanleitung

Boston Acoustics

Boston Acoustics P4FL Bedienungsanleitung

Boston Acoustics

Boston Acoustics DSI255 Bedienungsanleitung

Boston Acoustics

Boston Acoustics HSi 455 Bedienungsanleitung

Boston Acoustics

Boston Acoustics SoundWare XL Bedienungsanleitung

Boston Acoustics

Boston Acoustics VS 224 Bedienungsanleitung

Boston Acoustics

Boston Acoustics Micro110c Bedienungsanleitung

Boston Acoustics

Boston Acoustics CRC Bedienungsanleitung

Boston Acoustics

Boston Acoustics CS 23 II Bedienungsanleitung

Boston Acoustics

Boston Acoustics VSi 560 Bedienungsanleitung

Boston Acoustics

Boston Acoustics VRi555 Bedienungsanleitung

Boston Acoustics

Boston Acoustics PC843LCR Bedienungsanleitung

Boston Acoustics

Boston Acoustics S65 Bedienungsanleitung

Boston Acoustics

Boston Acoustics Voyager RK5 Bedienungsanleitung

Boston Acoustics

Boston Acoustics Lynnfield VR-M50 Bedienungsanleitung

Boston Acoustics

Boston Acoustics CS225 Bedienungsanleitung

Boston Acoustics

Boston Acoustics SC85 Bedienungsanleitung

Boston Acoustics

Boston Acoustics TVee Model Two Bedienungsanleitung

Boston Acoustics

Boston Acoustics Bravo II Center Bedienungsanleitung

Boston Acoustics

Boston Acoustics CS 275 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung