Bradley TDB3105 Bedienungsanleitung

P.O. Box 309, Menomonee Falls, WI USA 53052-0309

PHONE 800.BRADLEY (800.272.3539) FAX 262.251.5817

bradleycorp.com

Installation

TDB3105

Terreon®36" Circular Deep Bowl

Washfountain with TouchTime®Control

215-1563 Rev. E; ECN 12-00-004

Page 1 of 22 1/15/2013

TDB3105 with

TouchTime Control Table of Contents

Pre-Installation Information ........................2

Circular Washfountain Dimensions ..................3

Rough-In Specifications......................... 4-5

Installing the Drain...............................6

Bowl/Pedestal Mounting and Assembly ..............7

Installing Drain Spud in Bowl.......................8

TouchTime®Assembly Installation ................ 9-12

Valve and Tubing Connections ....................13

Valve and Electrical Connections ..................14

Adjust the Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Cleaning and Maintenance .................... 15-17

Soap Valve Parts List and Maintenance .......... 17-18

Sprayhead Parts List and Troubleshooting ...........19

TouchTime Troubleshooting.......................20

Solenoid Valve Troubleshooting....................21

Thermostatic Mixing Valve Troubleshooting...........22

Available in standard height,

juvenile height, and TAS height.

IMPORTANT!

Read this entire installation manual to ensure proper installation. When finished with the

installation, file this manual with the owner or maintenance department.

Separate parts from packaging and make sure all parts are accounted for before discarding

any packaging material. If any parts are missing, do not begin installation until you obtain

the missing parts.

Make sure that all water supply lines have been flushed and then completely turned off

before beginning installation. Debris in supply lines can cause valves to malfunction.

Product warranties may be found under “Product” on our web site

at www.bradleycorp.com.

Installation

THIS

SIDE

Packing List

•

TDB3105 Installation

21/15/2013 Bradley • 215-1563 Rev. E; ECN 12-00-004

Supplies Required by Installer

• (4) 1/2" lag bolts, screws or other fasteners to anchor washfountain pedestal

• 1/2" nominal copper tubing for hot and cold water supply lines

• Standard P-trap (vented trap supplied by Bradley when required)

• 2" drain lines and fittings

• Teflon tape or pipe dope

• 1-1/2" vent or tie pipe on types vented through washfountain column

• 110 VAC GFI power source for 110/24 VAC UL Class II transformer supplied

• OPTIONAL: Bradley recommends installing an electrical cutoff switch to the unit. This feature allows no accidental

water delivery during regular maintenance and service.

Pre-Installation Information

Terreon Material

The Washfountain is constructed of Terreon®, a densified solid surface material composed of polyester resin. Terreon is resistant to

chemicals, stains, burns and impact. Surface damage can be easily repaired with everyday cleaners or fine-grit abrasives. Terreon

is NAHB certified to meet ANSI Z124.3, Z124.6 and ANSI/ICPA SS-1-2001.

TouchTime

Pushing the TouchTime®button allows the user to activate a solenoid valve. This starts the flow of water with a 15 second run

time.

Installation TDB3105

Bradley • 215-1563 Rev. E; ECN 12-00-004 1/15/2013 3

Circular Washfountain Dimensions

Model TDB3105

36" Circular

45-1/4"

(1149)

41-5/8"

(1057)

34"

(864)

18-1/2"

(470)

36"

(914)

9-3/4"

(248)

Optional equipment may not comply with all

ADA or TAS dimensional guidelines

23-1/2"

(597)

8-3/4"

(222)

Model TDB3105

36" Circular with Optional Accessories

Model TDB3105 (Juvenile/TAS Height)

36" Circular with Optional Accessories

Adjust to Towel Dispenser

Mounting Holes

(152)

59"* (1499) w/

Soap

50-1/2"* (1283)

w/o Soap

51-1/8"*

(1299)

42-3/4"*

(1085)

39-1/8"*

(994)

30"*

(762)

23-1/2"*

(597)

18-1/2"

(470)

36"

(914)

9-3/4"

(248)

(mm)

Adjust to Towel Dispenser

Mounting Holes

(152)

53-5/8"

(1362)

45-1/4"

(1149)

41-5/8"

(1057)

34"

(864)

23-1/2

(597)

18-1/2"

(470)

36"

(914)

9-3/4"

(248)

8-3/4"

(222)

61-1/2" (1562)

w/ Soap

53" (1346)

w/o Soap

Model TDB3105 (Juvenile/TAS Height)

36" Circular

42-3/4"*

(1085)

39-1/8"*

(994)

30"*

(762)

18-1/2"

(470)

36"

(914)

9-3/4"

(248)

23-1/2"*

(597)

8-3/4"

(222)

8-3/4"

(222)

* Add 2" (51) for TAS height unit

TDB3105 Installation

41/15/2013 Bradley • 215-1563 Rev. E; ECN 12-00-004

(mm)

Rough-In Specifications

Type A

Off-line vent with

supplies from below

8-1/2"

(216)

4-1/4"

(108)

1-5/8"

(41)

1/2" Nominal Copper

Tubing for Supplies

Through Floor, Stub Up

2-1/2" (64) Above Floor

Cold

Hot

4-1/8"

(105)

2" NPT Drain,

Stub Up 3" (76)

Above FLoor

(51)

4-3/4"

(121)

3-7/8"

(98)

(127)

Suggested

Electrical Outlet

Location

36" (914) Bowl

Type B

Centrally rising vent with

supplies from above

1/2" Nominal

Copper Tubing,

Supplies from

Above

7/8" (22)

Cold

1-1/2" NPT

Vent to Ceiling

1-5/8"

(41)

1-1/4"

(32)

(127)

Suggested

Electrical Outlet

Location

3-7/8"

(98)

4-1/4"

(108)

8-1/2"

(216)

4-1/8" (105)

2" NPT Drain,

Stub Up 3" (76)

Above Floor

36" (914) Bowl

Hot

Installation TDB3105

Bradley • 215-1563 Rev. E; ECN 12-00-004 1/15/2013 5

Type H

Centrally rising vent

with supplies from

below

8-1/2"

(216)

4-1/4"

(108) 1-5/8"

(41)

1/2" Nominal Copper

Tubing for Supplies

Through Floor, Stub Up

2-1/2" (64) Above Floor

Cold

Hot

4-1/8" (105)

2" NPT Drain,

Stub Up 3" (76)

Above FLoor

(51)

4-3/4"

(121)

3-7/8"

(98)

(127)

Suggested

Electrical Outlet

Location

36" (914) Bowl

1-1/2" NPT

Vent to Ceiling

(mm)

Rough-In Specifications

Type O

Off-line vent with

supplies from above

1/2" Nominal

Copper Tubing,

Supplies from

Above

7/8" (22)

Cold

Hot

1-5/8"

(41)

1-1/4"

(32)

(127)

Suggested

Electrical Outlet

Location

3-7/8"

(98)

4-1/4"

(108)

8-1/2"

(216)

4-1/8" (105)

2" NPT Drain,

Stub Up 3" (76)

Above Floor

36" (914) Bowl

TDB3105 Installation

61/15/2013 Bradley • 215-1563 Rev. E; ECN 12-00-004

1Installing the Drain

ARough in supply and drain piping as

required for your installation.

BAssemble the drain to the dimension shown

below for the bowl size you are installing.

All piping shown in dotted lines

to be supplied by installer.

Table 1 — “B” Trap Dimensions

Dim Standard Height Juvenile Height TAS

B 25" (635) 22-1/2" (572mm) 24-1/2" (622mm)

Vent or Tie Pipe

(Supplied by

Installer) Vented Trap

(111-024)

B - See Table 1

(102)

Centerline of

Washfountain

Types B, H

2" NPT Coupling if Tie

Pipe is Not Required

(Supplied by Installer)

B - See Table 1

(102)

Centerline of

Washfountain

Types A, O

Vent or Tie Pipe

(Supplied by

Installer) Optional Tie Pipe

Bracket (S70-082)

B - See Table 1

(102)

Centerline of

Washfountain

Types A, O with Tie

Pipe Bracket Option

See Rough-In information for

dimensions not shown.

Installation TDB3105

Bradley • 215-1563 Rev. E; ECN 12-00-004 1/15/2013 7

CAUTION! Bowl surface is very smooth. Approximate

weight of bowl is 73 pounds. Handle with Care!

2Bowl/Pedestal Mounting and Assembly

Top View

Drain Position with

Optional B-Trap

Front View

Place Hands

Here When

Lifting Bowl

Kick Ring

Threaded

Rods (4)

Places

1/4" Washers and

Wing Nuts (4) Places

Place Hands

Here When

Lifting Bowl

Valve Bracket

Washer and Screw

Before attaching 1/4" wing nuts and washer to

threaded rod, remove red protective caps from

threaded rods. Discard sleeve caps after removal.

APosition the pedestal making sure the

floor mounting holes (4) line up. Mark the

mounting hole positions.

TAS OPTION: Place TAS spacer on floor

over the mounting holes. Place pedestal on

top of the spacer.

BSecure pedestal to floor with suitable

fasteners, 1/2" anchors and bolts (supplied

by installer). Do not overtighten.

CInstall valve mounting screws into valve

mounting bracket.

Using two people, carefully lift bowl. Place

bowl onto pedestal, making sure drain

holes line up with floor drain and mate

thread rods with slotted holes in pedestal

using locator ribs.

EUsing 1/4" wing nuts and washers, secure

the bowl to the pedestal in four places.

Threaded Rods

(Qty 4)

Floor Mounting

(Qty 4)

Drain Position without

Optional B-Trap

TDB3105 Installation

81/15/2013 Bradley • 215-1563 Rev. E; ECN 12-00-004

3Installing Drain Spud in Bowl

ALoosely attach the drain spud to the bowl

with the locknut and washer.

Seal between drain spud and drain hole with

plumber’s putty (supplied by installer).

Strainer

(S45-067)

Spud

(112-015)

Washer

(142-068)

Drain Pre-Pack

(S45-273)

Bowl

Locknut

(161-021)

BTighten the spud and lock nut against bowl.

B Trap Option: Attach B trap to drain spud.

Tie Pipe Option: Attach tie pipe bracket to

drain spud.

CSecure the strainer to drain spud with screws

provided.

DConnect spud (or B Trap or Tie Pipe Bracket)

to drain.

Installation TDB3105

Bradley • 215-1563 Rev. E; ECN 12-00-004 1/15/2013 9

4a TouchTime Assembly for A and O Units Without Tie Pipe Option

AInstall hemmed end (not sharp end) of

support tube with gasket onto bowl.

Connect 3/8" supply tubing to sprayhead with

tube connector and place sprayhead onto

support tube. Run the tubing down through

the support tube to valve tube connector.

Place the upper tie bar (notched at both

corners of each end) on top of sprayhead.

Connect the longer tie rod to the 4-1/4" tie

rod using the coupling nut with hex head

set screws. Run the tie rod assembly down

through upper tie bar and secure from

underneath the bowl using lower tie bar (no

notches) and hex nut with socket head set

screw.

Tie Rod Pre-Pack Cover

Actuator

Module

Assembly

Coupling

Nut

Sprayhead Tie Bar

Tie Rod

Supply Tube

Section View of

A/O Unit Assembly

Tie Rod Pre-Pack

(S45-1336)

Top Cover

(107-099 (A))

(107-179 (O))

Module Cover

(S04-083)

Sprayhead

(S05-054)

Drain

(S45-273)

Terreon®Deep Bowl (ADA bowl

shown) (Part No. Varies with color of

bowl and height of unit. Contact your

local Bradley Rep for assistance)

Access Panel

(186-1469)

Standard Pedestal Assembly

(S17-337)

TAS Pedestal Assembly

(S17-338)

Tie Bar Pre-Pack

(S45-055)

Support

Tube Gasket

(125-011)

Support Tube

(S57-006)

Tie Bar

TT Module Assembly

(S83-179)

Nut

3/8" Supply

Tube

Tie Rod

(176-008)

A/O

(A Shown)

TDB3105 Installation

10 1/15/2013 Bradley • 215-1563 Rev. E; ECN 12-00-004

4a TouchTime Assembly for A and O Units Without Tie Pipe Option

continued...

Place the TouchTime actuator module assembly

on top of sprayhead. Rotate until actuator module

locks in with tie bar. Drop TouchTime module wires

down the support tube.

Skip to step F for units without soap.

For units with soap option, install the spacer, soap

dispenser and cover using the third tie rod (8-5/8"

long) and second coupling nut as shown. Secure

with acorn nut and set screw.

FSecure TouchTime actuator module cover and top

cover with acorn nut and set screw.

GConnect stops to supply stub-outs.

Unit with "O" Drain and Actuator Module

Shown, Also Available with "A" Drain

Top

Cover

Soap

Dispenser

8-5/8" Tie Rod

Spacer

Coupling

Nut

Module

Cover

4-1/4" Tie Rod

TT Module

Assembly

(S83-179)

Coupling

Nut

Tie Bar

Sprayhead

(S05-054)

Support Tube

(S57-006)

Tie Rod

Inhaltsverzeichnis

Andere Bradley Badezimmerarmatur Handbücher

Bradley

Bradley Advocate AV Series Bedienungsanleitung

Bradley

Bradley Verge LVRD Series Bedienungsanleitung

Bradley

Bradley SXWS9151 Bedienungsanleitung

Bradley

Bradley CBSHWR9000KD Bedienungsanleitung

Bradley

Bradley S19-120HFP Bedienungsanleitung

Bradley

Bradley Bradmar 400 Series Bedienungsanleitung

Bradley

Bradley HN-200 Bedienungsanleitung

Bradley

Bradley 500 Series Bedienungsanleitung

Bradley

Bradley Express EXD Series Bedienungsanleitung

Bradley

Bradley S19-110BF Bedienungsanleitung

Bradley

Bradley S19-310UU Bedienungsanleitung

Bradley

Bradley S19-310 Bedienungsanleitung

Bradley

Bradley 400 Series Bedienungsanleitung

Bradley

Bradley 400 Series Bedienungsanleitung

Bradley

Bradley S19-270HD Bedienungsanleitung

Bradley

Bradley S19-120 Bedienungsanleitung

Bradley

Bradley Verge LVSD2 Bedienungsanleitung

Bradley

Bradley Terreon Classic WF2500 Series Bedienungsanleitung

Bradley

Bradley Bradmar 700 Series Bedienungsanleitung

Bradley

Bradley S19-304C2 Bedienungsanleitung

Bradley

Bradley ABP-1WCA Bedienungsanleitung

Bradley

Bradley S19-310TW8 Bedienungsanleitung

Bradley

Bradley LOFT Series Bedienungsanleitung

Bradley

Bradley S19-310FW Bedienungsanleitung

Beliebte Badezimmerarmatur Handbücher anderer Marken

DURAVIT

DURAVIT C.1 C15240 0090 Handbuch

Heatstore

Heatstore HSTRL500WTN Bedienungsanleitung

Sunshower

Sunshower PURE SOLO Bedienungsanleitung

Delabie

Delabie Delabie Sporting 714700 Bedienungsanleitung

Kohler

Kohler K-13056 Montageanleitung

ESS

ESS Container TCL-11 Bedienungsanleitung

Mustee

Mustee 22C Bedienungsanleitung

VITRA

VITRA V-Flow Bedienungsanleitung

baliv

baliv DUK-80.30 T Bedienungsanleitung

Malmet

Malmet B105BT Bedienungsanleitung

bathstore

bathstore Transition H1690MM Leitfaden

BELLOSTA

BELLOSTA Edward 0800/M Bedienungsanleitung

baliv

baliv DU-5160 Bedienungsanleitung

Franke

Franke PRTR0006 Bedienungsanleitung

Gessi

Gessi RILIEVO 59011 Bedienungsanleitung

noken

noken VITAE 100188525-N299998810 Bedienungsanleitung

Allen + Roth

Allen + Roth 1142VA-30-201 Bedienungsanleitung

Britex

Britex HBDA Bedienungsanleitung