Bradley Equa-Flo S59-1005SR Bedienungsanleitung

Installation

P.O. Box 309

Menomonee Falls, WI 53052 USA

800 BRADLEY (800 272 3539)

+1 262 251 6000

www.bradleycorp.com

215-1674 Rev. F: ECO 19-03-024

Page 1 of 3 1/8/2020

S59-1005SR

Bradley Equa-Flo™HD Ligature

Resistant Pressure-Balancing

Shower Valve

Table of Contents

Safety Information ............................... 2

Supplies Required ............................... 2

Rough-In ...................................... 3

Connect Valve and Adjust Valve Temperature.......... 4

Attach Escutcheon and Handle ..................... 4

Read the instructions in this manual before beginning installation.

Save these instructions and refer to them for inspection,

maintenance, and troubleshooting information.

For questions regarding the operation, installation or maintenance of this product, visit bradleycorp.com or

call 800.BRADLEY (800.272.3539).

Product warranties and parts information may also be found under “Resources” on our website at

bradleycorp.com.

For use with shower heads rated

at 5.7 L/min (1.5 gpm) or higher.

S59-1005SR Installation

21/8/2020 Bradley • 215-1674 Rev. F: ECO 19-03-024

Safety Information

To ensure proper operation:

Installation

Failure to comply with proper installation and maintenance instructions could contribute to a valve failure resulting in severe bodily

injury including scalding, chilling, and/or death depending upon system water pressure changes and/or supply water temperature

changes.

Hot limit screw is set in the maximum temperature position. Failure to properly adjust may result in serious scalding. This valve

may not protect from scalding if there is a failure of other temperature-controlling devices elsewhere in the plumbing system.

Excessive heat may cause damage to internal parts.

This valve is intended to be installed as an ASSE 1016 valve- at the point of use, where the user has access to flow or final

temperature controls. This valve should not be used where an ASSE 1017, ASSE 1069, or ASSE 1070 device is required.

Make sure that all water supply lines have been flushed and are then completely turned off before beginning installation. Debris in

supply lines can cause valves to malfunction.

Installation of this system must be completed by a qualified plumber in compliance with all national and local codes. Compliance

and conformity to local codes and ordinances is the responsibility of the installer. Should these codes differ from the information in

the manual, follow the local codes. Inquire with governing authorities for additional local requirements.

Inspection

Regular checking and cleaning of the valve's internal components and check stops is necessary for maximum life and proper

product function. Periodic inspection and yearly maintenance by a licensed contractor is required. Corrosive water conditions

and/or unauthorized adjustments or repairs could render the valve ineffective for its intended service. Frequency of cleaning and

inspection depends upon local water conditions.

Supplies Required:

• Teflon Tape

• Allen key wrenches

• Screwdriver

• 1/2" NPT Brass pipe plug

• Adjustable wrench

• 100% Silicone Sealant

• Semi-Permanent Threadlocker

• Security sealant (if required)

• Silicone Grease (supplied)

Installation S59-1005SR

Bradley • 215-1674 Rev. F: ECO 19-03-024 1/8/2020 3

• Rough-in 1/2" NPT hot and cold water supply piping (supplied by installer) as shown below.

• For finished wall, make a 4-1/2" hole in the wall where the shower handle is desired.

HOT

COLD

SUPPLIES REVERSED

STANDARD INSTALL

Contact your Bradley

Representative and ask for

S45-2264 Back-to-Back Rotor

Kit to swap out the rotor on the

reversed side.

"Back-to-Back" Installation

6-1/2" (165)

w/Stops

2-1/2" (64)

w/o Stops

Hot Cold

1-3/4"

(46)

(mm)

Rough-in

WARNING! In order for the shower to be ligature resistant, the valve inlet and outlet rough-ins

must be 4" (±1/8").

2-1/8"

(53)

1-1/2"

(38)

1-1/2"

(38)

48"

(1219)

Above

Finished

Floor

2-1/4"

(56)

4"*

(103)

4-5/8"*

(119)

Finished Wall

1/2" NPT Inlets

and Outlets

1/2" NPT

Pipe Plug

(By Installer)

Valve must

be 90° to wall

* Dimension can be ±1/8"

S59-1005SR Installation

41/8/2020 Bradley • 215-1674 Rev. F: ECO 19-03-024

APosition valve with port labeled “UP” towards showerhead.

Connect valve to hot and cold supplies and showerhead

or tub spout supplies (see rough-in diagram.)

Turn on hot and cold supplies to pressurize valve and check for

leaks. (Valve will not operate unless both hot and cold supplies

are turned on.) Adjust maximum temperature by turning set

screw on valve cap.

Insert the 4 screws through the

escutcheon and into the valve body.

Tighten the screws, making sure that

the escutcheon is flush with the wall or

fixture and all 4 screws are tightened

equally.

WARNING! The temperature limit stop has been

factory preset for maximum temperature

operation. Failure to adjust the limit screw

to a safe shower temperature could result

in the user being scalded.

Connect Valve and Adjust Valve Temperature

Attach Escutcheon and Handle

DApply 100% silicone caulk to all

screw backsides prior to escutcheon

installation.

Slide handle over stem. Apply semi-

permanent thread locker to set screw

and tighten to ensure the screw is fully

engaged.

BApply supplied silicone

grease to o-ring to guide

escutcheon in place.

CSlide escutcheon on

valve and align all 4

holes.

FApply security sealant

(if required) as

described below.

After installation, all joints

require security sealant (by

installer) to eliminate gaps,

if present, between the wall

and fixture.

Andere Bradley Steuereinheit Handbücher

Bradley

Bradley EFX 125/S19-2300 Bedienungsanleitung

Bradley

Bradley EFX60 Bedienungsanleitung

Bradley

Bradley HL 200 Bedienungsanleitung

Bradley

Bradley EFX 125 Bedienungsanleitung

Bradley

Bradley S67-610 Bedienungsanleitung

Bradley

Bradley EFX 20-2150 Bedienungsanleitung

Bradley

Bradley EFX 120 Series Bedienungsanleitung

Bradley

Bradley Navigator S59-4016 Series Bedienungsanleitung

Bradley

Bradley EFX25 Bedienungsanleitung

Bradley

Bradley S45-1986 Bedienungsanleitung

Bradley

Bradley S59-2005T1 Bedienungsanleitung

Bradley

Bradley S19-2100 Bedienungsanleitung

Bradley

Bradley Equa-Flo HD S59-1005 Bedienungsanleitung

Bradley

Bradley S59-2007 Bedienungsanleitung

Bradley

Bradley Equa-Flo HD Bedienungsanleitung

Bradley

Bradley Equa-Flo EFT1 Bedienungsanleitung

Bradley

Bradley Navigator S59-4007 Bedienungsanleitung

Bradley

Bradley Navigator S59-4000 Bedienungsanleitung

Bradley

Bradley S19-2000EFX Series Bedienungsanleitung

Bradley

Bradley EFX 20/S19-2150 Bedienungsanleitung

Bradley

Bradley EFX 60 S19-2200 Series Bedienungsanleitung

Bradley

Bradley EFX8/S19-2000 Series Bedienungsanleitung

Bradley

Bradley S90-252 HFP Leitfaden

Bradley

Bradley AST4 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung