Brady 1024 Bedienungsanleitung

BradyprinterTHT Model

1024 Thermal Transfer Printer

_______________________________________________________________________________

User’s Guide

LOGO W.H. Brady Co.

Automatic Indentification Products

CG Triumvirate is a trademark of Agfa Corporation.

Corrupad is a Trademark of Corrupad Protective Packaging Inc.

Bradyprinter THT Model 1024 is a Trademark of Brady USA Inc.

As an Energy Star Partner, Brady USA Inc. has determined that this

product meets the Energy Star guidelines for energy efficiency.

Information in this document is subject to change without notice and does

not represent a commitment on the part of Brady USA Inc. No part of this

manual may be reproduced or transmitted in any form or by any means,

for any purpose other than the purchaser's personal use, without the

expressed written permission of Brady USA Inc.

6555 W. Good Hope Road •Milwaukee, Wisconsin •53223

800-537-8791 Customer Support

800-643-8766 Technical Support

Part Number: 88-2184-01

Revision: C

Agency Compliance and Approvals:

FCC: This device complies with Part 15 of FCC rules.

Note: This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and

can radiate radio frequency energy, and if not installed and used

in accordance with the instructions in this manual, it may cause

harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the

interference at his own expense.

Important Safety Instuctions

Your Bar Code Printer has been designed to give you many years of

safe, reliable service. As with all electrical equipment, there are a few

basic precautions you should take to avoid getting hurt or damaging the

Printer.

•Carefully read the installation and operating instructions provided

with your Printer.

•Read and follow all warning instruction labels on the Printer

itself.

•Place the Printer on a flat, firm, solid surface.

•To protect your Printer from overheating, make sure all openings

on the Printer are not blocked.

•Do not place the Printer on or near a heat source, (i.e., a radiator

or heat register).

•Do not use your Printer near water, or spill liquid of any kind into

it.

•Be certain that your power source matches the rating listed on the

bottom of the Printer. If you are unsure, check with your dealer

or with your local power company.

•Do not place the power cord where it will be walked on. If the

power cord becomes damaged or frayed replace it immediately.

•Do not insert anything into the ventilation slots or openings on the

Printer.

•Only qualified, trained service technicians should attempt to

repair your Printer.

♦♦ Contents

♦♦ Getting Started

1.0 Introduction ...............................................................1

1.1 Unpacking and Inspection...........................................1

1.2 Printer Specifications .................................................2

1.3 Connecting Power......................................................4

1.4 Switches and Indicators..............................................5

1.5 Interfacing to the Printer.............................................6

1.6 Loading Media...........................................................7

1.7 Loading Media for Peel Configuration........................8

1.8 Loading Ribbon (Thermal Transfer)..........................9

1.9 Adjusting for Wide to Narrow Media........................11

1.10 Power-up Configuration and Self-Test......................12

1.11 Available Options ....................................................13

♦♦ Printing Labels

2.0 Introduction .............................................................15

2.1 Programming Commands .........................................16

2.2 Programming Examples ...........................................21

2.3 Configuration Command String................................22

2.4 Printing Bar Codes...................................................23

2.5 Memory Cartridges (Modules)..................................24

♦♦ Maintenance

3.0 Introduction .............................................................25

3.1 Cleaning the Printhead..............................................25

3.2 Media Width Adjustment..........................................26

3.3 Fine Printhead Adjustment........................................27

3.4 Printhead Replacement.............................................28

(continued)

Appendix A

ASCII Control Code Chart ..............................................A-1

Appendix B

Available Fonts and Bar Codes........................................B-1

Appendix C

Error Codes.....................................................................C-1

Appendix D

Warranty Information......................................................D-1

Getting Started 1

♦♦ Getting Started

Figure 1-1 Printer Overview

1.0 Introduction

The BradyprinterTHT Model 1024, hereafter referred to as 'the Printer',

incorporates high performance/low cost thermal transfer label printing

capabilities. The combination of powerful capabilities, compact design,

and easy to use features make this Printer truly unique.

1.1 Unpacking and Inspection

Inspect the shipping container(s), if damage is evident, contact the carrier

to specify the nature and extent of the damage.

The Printer is packed in Corrupadrecycled packaging and is enclosed

in a plastic bag to reduce the chance of moisture damage during shipment.

Remove the Printer from the plastic bag before use.

Along with this manual, the shipping container(s) should include the

following standard items:

•Label printer

•External power supply

•Special or additional items purchased.

2Getting Started

1.2 Printer Specifications

Mechanical

Width 8.8" (22.35 cm)

Depth 10.1" (25.65 cm)

Height 6.2" (15.75 cm)

Weight 7 lbs. (15.4 kg)

Operating Temperature 40°F to 100°F (4°C to 38°C)

Printer Specifications

Print Type Thermal Transfer

Print Speed 1, 1.5, and 2" per second

Resolution 203 dpi (8 dots/mm)

Tear Bar Tear up

DRAM Memory 512 kb

EPROM Memory 512 kb

Media/Ribbon

Media Types Roll-Fed, Die-Cut, Continuous, Fan-Fold

Max. Media Width 4.65" (118 mm)

Max. Print Width 4.1" (104 mm)

Min. Print Width 1" (25 mm)

Max. Print Length 12" (305 mm) with standard RAM

Min. Print Length .375" (.95 cm)

.5" (1.27 cm) w/ Present Sensor

Media Thickness .0025" - .01" (.0635 mm - .254 mm)

Ribbon Matched to Media; approx. 4330"(110m)

long

1.5" O.D. on .5" core

Getting Started 3

Communications

Interface RS-232 (DB-9), and Centronics Parallel

Baud Speed 1200 to 19200 bps

Handshaking Xon/Off, CTS, DTR

Parity Even, Odd, or None

Stop Bits 1 or 2

Data Bits 7 or 8

Electrical

External Power Supply Nominal 115 or 230 VAC IN/ 19 VAC OUT

Fonts

10 Resident Styles

Resident Fonts Expandable to 8x

Reverse Image

Rotated 0, 90, 180, 270 degrees

Available Bar Codes

Code 39, Ext Code 39, Code 93, Ext Code 93, Code 128 UCC, Code 128

A, B & C, Codabar, Interleaved 2 of 5, UPC-A, UPC-E, UPC Ship C

Code, EAN-13, EAN-8, EAN 128, POSTNET, MaxiCode, PDF417

Options

Present Sensor

Memory Cartridges

External Cutter

DRAM Memory, (Expandable to 1MB)

Wall Mount

External Battery

Time/Date

External Media Supply

4Getting Started

1.3 Connecting Power

The Printer is powered from an External Power Supply. The supply

connects to the Printer as shown below. Power supplies are available for

115 and 230 AC voltages. Ensure that the power supply shipped with the

Printer matches your electric service.

Caution!

Connect power supply to Printer before plugging into AC

outlet.

Figure 1-2 External Power Supply

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Brady Drucker Handbücher

Brady

Brady Tagus Bedienungsanleitung

Brady

Brady IP300 Bedienungsanleitung

Brady

Brady BBP11-34L Bedienungsanleitung

Brady

Brady BBP81 Bedienungsanleitung

Brady

Brady BradyPrinter M611 Bedienungsanleitung

Brady

Brady BradyPrinter S3000 Bedienungsanleitung

Brady

Brady Bradyprinter 200MVP Bedienungsanleitung

Brady

Brady BP-PR PLUS Series Handbuch

Brady

Brady BradyPrinter S3700 Bedienungsanleitung

Brady

Brady BradyPrinter M611 Bedienungsanleitung

Brady

Brady TLS2200 Bedienungsanleitung

Brady

Brady LS2000 Bedienungsanleitung

Brady

Brady BBP 33 Bedienungsanleitung

Brady

Brady PAM 3000 Bedienungsanleitung

Brady

Brady SLV-DAT-PRO Bedienungsanleitung

Brady

Brady TLS2200 Bedienungsanleitung

Brady

Brady 2024 Bedienungsanleitung

Brady

Brady touch print Bedienungsanleitung

Brady

Brady BP-1244 Bedienungsanleitung

Brady

Brady THT-BP Precision Bedienungsanleitung

Brady

Brady BBP16 Bedienungsanleitung

Brady

Brady BRADYMARKER XC Plus Bedienungsanleitung

Brady

Brady BradyPrinter M611 Bedienungsanleitung

Brady

Brady BMP71 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung