Brandt VF400JU1 Bedienungsanleitung

Pages

Installing your dishwasher....................................31-36

Levelling by adjusting the feet .................................31

Anti-condensation protection ...................................31

Facing the door ......................................................32

Balancing the door .................................................32

Building in and fixing the dishwasher.......................32

Water connections ..................................................33

Draining away the waste water................................34

Electrical connection ...............................................34-35

Foam strip and soundproofing sea ...........................36

Installing the plastic corner brackets........................36

Safety instructions ...............................................36

Building in under a hob.........................................36

Contents

EN 31

Installing your dishwasher

Levelling by adjusting the feet

Ensure that your dishwasher is well

balanced and stable. The four feet can

be adjusted, so adjust them if necessary

using a screwdriver. If the feet are

poorly adjusted, this decentres the door

and makes your dishwasher wobble,

causing leaks.

For dishwashers that can be built-in,

fitted with rear feet adjustment via two

knurled knobs on the base of the

machine, at the front, use a screwdriver,

without exerting force, to finish the

adjustments to avoid damaging the

worktop.

Protecting the worktop

Glue the steam protector supplied with

your machine underneath your worktop.

Built-in appliance cup kit

(available according to the model from

After-Sales or the dealers)

To assist in sliding your dishwasher

(over rough or carpeted floors, etc.),

clip the little cups to all four feet.

Remove the 2 red

protective wedges from

the front of your appliance to

avoid causing a leak.

Facing the door

To fit a door to match your units

onto the dishwasher’s door, use the

installation template and the

accessories supplied with your

machine.

Balancing the door (right and

left)

Adjust the tension on the springs, if

required, to compensate for the

weight of the facing panel. Adjust in

an identical fashion to the right and

to the left.

Fix your dishwasher to the worktop

with two screws under the front

corner bracket.

If your worktop is marble or a

similar material, you can fasten

your dishwasher in place at the

sides using two brackets (available

from the After-Sales department or

from your dealer).

Installing your dishwasher

This dishwasher

must operate with a

wood panel.

Installing your dishwasher

Tap: with threaded end, 20/27mm

dia. (3/4” BSP)

Flow: 10l/min. minimum

Pressure: 1 bar to 10 bars

(0.1 - 1 MPa)

In the event of high pressure, it is

advisable to fit a pressure regulator.

Your Water Company will give you

the necessary information.

Length of the water supply pipe

(standard unit): 1.50m

Connecting the hot water:

Check that your original hose is

designed for connection to the hot

water supply (red marking on the

hose).

If necessary, you can alter the

hose’s direction. To do this, loosen

the connection at the bottom left

on the rear of the machine and

swivel it as necessary. Fully tighten

the connection again and check

that there are no leaks.

For dishwashers fitted

with safety hoses:

You must remove the

protective cover (see

the drawing opposite)

to alter the hose’s

direction. To do this,

loosen the two

screws (end fitting

T20), remove the

protective cover,

position the

connection in the

direction you wish and then

replace the protective cover.

If you use a self-

piercing tap, check that

there is sufficient water flow.

When the tap is on the left-

hand side of the machine, use the

“anti-kinking” hook supplied with the

machine to avoid any risk of the

supply hose* kinking while you are

fitting your dishwasher.

(* For large diameter safety hoses-

depending on the model)

Check that the

seal is fitted

and that the

connection is

tight.

When you are making a

new installation, you must

use a new hose to connect the

machine to the water supply: you

must not re-use the old hose.

Water connections

“Hazardous Voltage” symbol

(depending on the model)

the hose is fitted with an electrical

device

Important :

check the water’s

hardness: all the

information you

require is provided in

the Chapter

“Adjusting the water

softener” in your

operating instructions

manual.

0,1 - 1 MPa

Installing your dishwasher

Draining away the waste water

Length of the drain hose: standard

1.50m. If necessary, you can

increase the length of the drain

hose (4m max.). In this case, check

that the machine drains correctly.

Connect the drain hose:

- To a ventilated siphon

- To a sink U-bend

Remove the stopper form the

U-bend.

Remove the rubber stopper and, if

necessary, add a collar.

- Directly to your sink.

Ensure that you hold your drain

hose in place with the end

connector to avoid flooding.

For machines installed in columns,

the height of the drain hose must

not be higher than the top of the

machine.

Electrical connection

Mains voltage: 230V

Fuse: 10A, 13A or 16A

The socket outlet must be

grounded to Earth.

In all cases, the connection must

comply with the standards in force

in the country concerned, together

with the supplementary regulations

of the Electricity Authority. The

machine must be switched off when

the connection is made to the

electrical circuit.

If you have any doubts regarding

the condition of your installation, do

not hesitate to have it checked by a

qualified electrician.

The machine must be installed so

that the socket remains accessible.

We cannot be held

liable for any damage

caused by the faulty earthing

of the machine.

NB: Pull the pipe

gradually when

installing it to avoid

kinking it.

Do not use an electrical extension,

a double socket or an electrical

timer. The installation must comply

with the country’s prevailing norms.

Your dishwasher complies with

European Directives 73/23/EEC

(Low Voltage Directive) and

89/336/EEC (Electromagnetic

Compatibility), modified by

Directive 93/68/EEC.

Installing your dishwasher

Replacing the power

cable

For your safety, this operation

must be performed by the

manufacturer’s After-Sales

department or a person with

similar training and experience

in order to avoid any risk.

IMPORTANT for the dishwasher without plug.

The wires in this mains lead ar coloured in accordance the

following code :

Green & Yellow Earth

Blue Neutral

Brown Live

As the colours of the wires in the mains lead of this appliance may not

correspond with the terminal in your plug, proceed as follows ; The wire

which is coloured Green and Yellow must be connected to the terminal

which is marked with the letter «E» or by the earth symbol or

coloured Green end Yellow.

The wire which is coloured Blue must be connected to the terminal

which is marked with the letter «N» or coloured Black.

The wire which is coloured Brown must be connected to the terminal

which is marked with the letter «L» or coloured Red.

Installation of the adjustable

plinth on built-in appliances

(depending on the model)

AVAILABLE FROM

THE AFTER-SALES

DEPARTMENT UNDER

REFERENCE: 32X0050

Installing your dishwasher

Foam strip and soundproofing

seal. To provide better noise

insulation on built-in appliances,

install the soundproofing seals and

the foam strip supplied with your

machine

(depending on the model).

Safety instructions

Building in under a hob

If your dishwasher is being installed on a carpeted floor, make

sure to adjust the feet to leave a ventilation space under the

machine

If your worktop is fitted with a built-in hob over your

dishwasher, you must provide thermal insulation on top of the

machine. You can obtain this insulation kit from your dealer. Take care

to leave a space between the gas pipe and the top of your machine.

If the machine is operating incorrectly, disconnect it from the

electricity supply (remove the plug) or switch off the circuit involved

and close the water supply tap. Contact our After-Sales department.

For your safety’s sake, never leave your dishwasher’s door fully

open after use.

Inhaltsverzeichnis

Andere Brandt Spülmaschine Handbücher

Brandt

Brandt DWJ137DS Bedienungsanleitung

Brandt

Brandt VH1472J Bedienungsanleitung

Brandt

Brandt DFS1009X Bedienungsanleitung

Brandt

Brandt BF3534CW Bedienungsanleitung

Brandt

Brandt BDF424VDX Bedienungsanleitung

Brandt

Brandt BDJ424DB Bedienungsanleitung

Brandt

Brandt VH1472X Bedienungsanleitung

Brandt

Brandt VH916J Bedienungsanleitung

Brandt

Brandt DFH15624X Bedienungsanleitung

Brandt

Brandt VS1009X Bedienungsanleitung

Brandt

Brandt BDF534DW Bedienungsanleitung

Brandt

Brandt BF3424CW Bedienungsanleitung

Brandt

Brandt VH1505W Bedienungsanleitung

Brandt

Brandt VF 300 Series Bedienungsanleitung

Brandt

Brandt DW9 Bedienungsanleitung

Brandt

Brandt VH1544X Bedienungsanleitung

Brandt

Brandt DWF137DW Bedienungsanleitung

Brandt

Brandt BDB424DX Bedienungsanleitung

Brandt

Brandt DWF128DW Bedienungsanleitung

Brandt

Brandt VH900JE1 Bedienungsanleitung

Brandt

Brandt DWJ127DS Bedienungsanleitung

Brandt

Brandt VM512XE1 Bedienungsanleitung

Brandt

Brandt VI 310 Bedienungsanleitung

Brandt

Brandt VS1009J Bedienungsanleitung

Beliebte Spülmaschine Handbücher anderer Marken

Electrolux

Electrolux ESI5211LOX Bedienungsanleitung

KitchenAid

KitchenAid KUDB230B Bedienungsanleitung

Asko

Asko DSD767UXXL.AU Bedienungsanleitung

Beko

Beko DFN26210W Bedienungsanleitung

NEFF

NEFF S153ITX00E Technisches Datenblatt

Midea

Midea SV 4.45 wi Bedienungsanleitung

LG LDF7932 Bedienungsanleitung

Gorenje

Gorenje GV63214 Bedienungsanleitung

Hotpoint

Hotpoint HDA1100ZWH Service-Handbuch

Blomberg

Blomberg LDFN2240W Bedienungsanleitung

AEG

AEG FFB83836PM Bedienungsanleitung

Cylinda

Cylinda DM3220RFD Bedienungsanleitung

Atag

Atag DW8214MB Bedienungsanleitung

GE GLD8000 Series Bedienungsanleitung

Siemens

Siemens SN23HI02KE Technisches Datenblatt

Omega

Omega ODW717X Bedienungsanleitung

BORETTI

BORETTI BVW-683 Bedienungsanleitung

Siemens

Siemens SN 56N591 Bedienungsanleitung