BREL BEQ35 Series Bedienungsanleitung

Page 1

Manual Brel bi-directional silent 35mm motor

Type BEQ35

Read the manual before you begin the installation If these instructions are not followed,

this may lead to defects and injury in which warranty can’t be claimed

warning:

Children cannot recognize the dangers of electrical equipment and may therefore not work with it.

It is important to follow this instruction for your own safety

Do not operate the motor in humid surroundings.

1. The motor must be installed correctly.

2. Keep the antenna in a good condition and do not shorten.

The antenna should not come into contact with other metal

parts otherwise it will reduce the effect.

. The motor must be protected from direct moisture influences.

4. BREL-Motors declares that this motor has been manufactured according to the guidelines of the CE standard 1999/5/EC

_______________________________________________________________________________

Wiring

_______________________________________________________________________________

Functions remote control Changing batteries

DD-2702

Works with all BREL transmitters:

Visit our website www BREL-HOME com for

More manuals and information

____________________________________________________________________________

Technical data of the motor BEQ35-6 BEQ35-10

 Voltage: AC 2 0V AC 2 0V

 Power: 144W 144W

 Torque: 6Nm 10Nm

 Maximum motor runtime: 4 min. 4 min.

 Speed: 28rpm 17rpm

 Amperage: 0.6 A 0.6 A

 Moisture and dust protection: IP44 IP44

Scan hier de QR code om de

Handleiding te downloaden

en instructie filmpjes te bekijken

BEQ35-6 BEQ35-10

NOTE:

If the motor has been

running continuously for 4

minutes, it may become too

hot and then stop After

approximately half an hour,

this one will continue to run

Page 2

_______________________________________________________________________________

Step 1 Setting up the first remote/channel

After power has been applied to the motor, press stop within 10 seconds

Tension motor 







 STOP until 2x 









Put tension on the motor, the product Press and hold the STOP button until the Transmitter/channel

moves up and down. The motor beeps. product moves 2x up and down and beeps x. has been set.

If NO end positions are set, the product will move in the pulse / step operation. Go then to STEP 2.

If end positions are set, the product will continue to its end position. Go then to STEP 4.

NOTE: The correct end positions ma not be set. Then go to OPTION A.

______________________________________________________________________________

Step 2 Adjusting the direction of rotation

Onl possible if no end positions are set, otherwise first option B (Delete end positions), after that, Step 2.

▲+▼ until 1x 









Press UP and DOWN button The direction of rotation of

simultaneously, until the product moves. the motor is OK

_______________________________________________________________________________

Step 3 Setting the end limits

1 Set the desired top position





 ▲+ STOP 2x 









Use the OPERATING- buttons to Press UP and STOP simultaneously, The desired top

move the product to the desired top position. until the product moves 2x and beeps x. position is set.

2 Set the desired bottom position





 STOP+▼ 2x









Use the OPERATING- buttons to move Press DOWN and STOP simultaneously, The desired bottom

the product to the desired bottom position. until the product moves 2x and beeps x. position is set.

_______________________________________________________________________________

Step 4 Setting the desired third limit position (If desired)





 1x P2 1x 







 1x STOP 1x 







 1x STOP 2x 









Set the desired Press 1x P2. Press 1x STOP button. Press 1x STOP button.

Third limit The product moves 1x The product moves 1x The product moves 2x up and

position. up and down and beeps. up and down and beeps. down and beeps x for confirmation.

Press and hold STOP for 3 seconds to move to the set limit position.

Page 3

______________________________________________________________________________

Additional settings

____________________________________________________________________________

Option A Adjusting the top position If adjustment is not possible, go to Option B, then to Step 3





 STOP +▲ until 







 



 STOP +▲ until 2x 









Go to the already Press at the same time Go to the new Press at the same time

set top position. STOP and UP until top position. STOP and UP button, until

the motor moves and beeps 1x. the motor 2x moves and x beeps.

___________________________________________________________________________

Adjusting the down position

If adjustment is not possible, go to Option B, then to Step 3





 STOP +▼ until 







 



 STOP +▼ until 2x 









Go to the already Press at the same time Go to the new Press at the same time

set bottom position. STOP and DOWN until bottom position. STOP and DOWN button, until

the motor moves and beeps 1x. the motor 2x moves and x beeps.

______________________________________________________________________________

Option B Deleting the end limits

1x P2 1x 







 1x ▼ 1x 







 1x P2 2x 









Press 1x P2. The product Press the DOWN button. Press P2. The product The end positions

moves up down and beeps 1x. The product moves 1x moves 2x up and down are now deleted

up and down and beeps 1x. and beeps 1x. from the memory.

_______________________________________________________________________________

Option C Deleting the third limit position

1x P2 1x 







 1x STOP 1x 







 1x STOP 1x 









Press 1x P2. Press 1x STOP button. Press 1x STOP button.

The product moves 1x up The product moves 1x up The product moves 1x up and

and down and beeps 1x. and down and beeps 1x. down and beeps 1x for confirmation.

_______________________________________________________________________________

Option D Learn new transmitter/channel while maintaining end limits Onl possible when end limits are set.

= Alread existing transmitter = New transmitter

Method 1

P2 a until 







 P2 a until 







 STOP b until 2x 









Press P2 of a. The product Press P2 of a. The product Press STOP of b. The product The transmitter b

moves 1x up and down moves 1x up and down moves 2x up and down has been added.

and beeps 1x. and beeps 1x. and beeps x.

Repeating the above will remove the new transmitter/channel.

Page 4

Method 2 (also sun- and windmeter)

P2 a until 







 P2 a until 







 P2 b until 2x 









Press P2 of a. The product Press P2 of a. The product Press P2 of b. The product The transmitter b

moves 1x up and down moves 1x up and down moves 2x up and down has been added.

and beeps 1x. and beeps 1x. and beeps x.

Repeating the above will remove the new transmitter/channel.

Method 3 (in case the old transmitter is lost or broken)

P1 until 







 STOP b until 2x 









Press P1 of a. The product moves 1x Press 1x STOP of b. The product The transmitter b

up and down and beeps 2x. moves 2x up and down and beeps x. has been added.

_______________________________________________________________________________

Optie E Pulse / jog control 1x 







, beeps 1x

▲+▼ until 1x 







 1x STOP

Pulse / jog on

Pulse / jog off

Press and hold UP and DOWN button, Press 1x STOP button.

until the product moves up and down.

2x 







 , beeps 3x

______________________________________________________________________________

Option F Sun and wind meter ( DD-116H )

_______________________________________________________________________________

Add / remove

1x P2a 1x 







 1x P2a 1x 







 1x P2b 2x 









The sun and wind meter has been added

Press P2 of a. The product Press P2 of a. The Press P2 of b. The

moves 1x up and down and product moves 1x up product moves 2x up

beeps 1x. and down and beeps 1x. and down and beeps x.

B repeating the above, ou can remove the sun and wind meter again.

Page 4

Page 5

On / off sun function ( Factory setting = on)

1x P2 1x 







 1x P2 1x 







 1x ▲ 









ON: The product moves up and down once and beeps once long

OFF: The product moves up and down 2x and beeps 3x long

Press 1x P2 The product Press 1x P2. The Press 1x UP

moves 1x up and down and product moves 1x up

beeps 1x. and down and beeps 1x.

B repeating the above, ou can switch the sun function on or off again.

_______________________________________________________________________________

Additional settings P1 button Can be used without a transmitter as an operating button

1x P1

The product moves up, stops or goes down when pressed P1

Press 1x P1 on the motor.

_______________________________________________________________________________

Switching off the receiver

P1, (6 sec ) until 2th x 









Press and hold P1 until the product moves The Receiver switched off.

up and down for the 2th time and beeps 2x.

To reactivate the receiver, briefl press P1 once.

______________________________________________________________________________

Changing the direction of rotation

P1, (10 sec ) until 3th x 









Press and hold P1 until the product moves The direction of rotation has changed.

up and down for the 3th time and beeps 3x

_______________________________________________________________________________

Resetting to factory settings

P1, (14 sec ) until 4th x 









Press and hold P1 until the product moves Resets to factory settings

up and down for the 4th time and beeps 4x Page 5

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere BREL Motor Handbücher

BREL

BREL BRE45 Bedienungsanleitung

BREL

BREL BPE Bedienungsanleitung

BREL

BREL BLE45-50 Bedienungsanleitung

BREL

BREL BZE45 Bedienungsanleitung

Beliebte Motor Handbücher anderer Marken

Rotax

Rotax 125 senior MAX evo Bedienungsanleitung

Kohler

Kohler K361 Bedienungsanleitung

MTD

MTD OHV Series Bedienungsanleitung

Kohler

Kohler COMMAND CH18-745 Bedienungsanleitung

Mercury

Mercury D4.2L D-Tronic Bedienungsanleitung

Selve

Selve SE Plus-RC Series Bedienungsanleitung

Perkins

Perkins 1206E-E66TA Bedienungsanleitung

Skov

Skov DA 174 Handbuch

Rossi

Rossi TX11 Series Bedienungsanleitung

Siemens

Siemens SIMOTICS T-1FW3 Merkblatt

AL-KO

AL-KO PRO 350 Bedienungsanleitung

MTU

MTU 12 V 4000 Lx4 Bedienungsanleitung

Nanni

Nanni N3.30 Gebrauchsanweisung

Nanni

Nanni N5.160 CR2 Bedienungsanleitung

KSB

KSB SuPreme Series Montageanleitung

Hiwin

Hiwin EM1 Series Bedienungsanleitung

Rotax

Rotax 912 i series Betriebsanleitung

Siemens

Siemens SIMOTICS XP 1MB1 Bedienungsanleitung