Brennenstuhl L2705 Bedienungsanleitung

L2705 / L2705 PIR

LED-LEUCHTE

Bedienungs- und Sicherheitshinweise LED-LigHT

Operation and Safety Notes

LED-Lamp

Bedienings- en veiligheidsinstructies

LampE LED

Instructions d‘utilisation et consignes de sécurité

Lámpara LED

Instrucciones de utilización y de seguridad Lampa LED

Wskazówki dotyczące obsługi i bezpieczeństwa

CanDEEiro LED

Instruções de utilização e de segurança

Φώτα LED

Υποδείξεις χειρισμού και ασφαλείας

LED Lampa

Lietošanas un drošības norādījumi

LED šviEsTUvai

Valdymo ir saugos nurodymai

LED-vaLgUsTiD

Kasutus- ja ohutusnõuded

LED-осветители

Инструкции по эксплуатации и технике безопасности

LED svETiLka

Navodila za upravljanje in varnostna opozorila

LED sviETiDLo

Pokyny pre obsluhu a bezpečnostné pokyny

LED-Lampa

Bruksanvisning och säkerhetsanvisningar

LampaDE a LED

Indicazioni per l’uso e per la sicurezza

LED-vaLaisin

Käyttö- ja turvallisuusohjeet

LED ayDinLaTmasi

Kullanım ve güvenlik uyarıları

LED-Lámpa

Kezelési és biztonsági utalások

LED svěTLo

Pokyny pro obsluhu a bezpečnostní pokyny

LED-Leuchte_Cover_L2705–2705 PIR_EU.indd 2 07.01.13 08:46

2,5m

2m 6m 10m

130°

2 1

LED-Leuchte_Content_L2705–2705 PIR_EU.indd 3 07.01.13 08:46

8GB

LED-light

(Models L2705 and L2705 PIR)

Parts description

1Screw for connector box

2Screw terminal

3Release button

4Mounting plate

5Screws for mounting plate

6Cable feed-through

7Wall plug

Safety notes

Note: Please ensure you read the following notes

before installing the light. Make sure the power is

switched oﬀ, before you install the light. The instal-

lation of the light should only be carried out by a

qualiﬁed expert.

This light may not be operated

unless all sealing rings are located properly!

LED-lights are extremely bright. Under no cir-

cumstances look into the light beam of the LED

lights, as this may cause permanent damage to

your eyes.

FIRE HAZARD! Fit the light so that it

is at least 1m away from the material

being illuminated. Excessive heat can

result in a ﬁre.

If the glass is broken, it must be replaced

with a new original Brennenstuhl pro-

tective glass before further use.

RISK OF INJURY FROM BURNS!

Ensure the

lamp has been switched oﬀ and allowed to cool

before you touch it.

Technical data

Voltage: 220-240V~50/60Hz

Wattage: 27 x 0,5W LED

Weatherproof: IP44

Protection: Class I

This luminaire is only intended for normal use, must

not be used for rough service.

Only for model L2705 PIR:

Detection area

movement detector: 130° and max. 10 metres,

adjustable

Time span: adjustable from 10 (±5) sec-

onds to 4 (±1) minutes

Installation

Note: The light must be ﬁtted to a dry, sturdy and

stable surface according to the notes in Fig. B.

Ideally the LED light should be ﬁtted at a height

of 1.8 bis 2.5 metres oﬀ the ground (see Fig. B).

Only for model L2705 PIR:

The movement detector should not be directed

towards heat sources, such as barbecues, air

condition units, other outside lights, passing

cars or ventilation openings, to avoid annoying

unwanted activation.

The movement detector should not be ﬁtted in

an area with strong electromagnetic interfer-

ences, to avoid annoying unwanted activation.

Do not point the appliance towards reﬂective

surfaces such as smooth white walls, swimming

pools, etc. The technical speciﬁcations for the

detection area (max. 10 metres at 130°) may

vary depending on ﬁtting height and place.

The detection area of the appliance can also

diﬀer with changing temperature. Before you

choose where to ﬁt the appliance, you should

take into consideration that movements perpen-

dicular to the movement detector are more ef-

fective than movements straight towards or

LED-Leuchte_Content_L2705–2705 PIR_EU.indd 8 07.01.13 08:46

9GB

away from the movement detector (see Fig. C).

If the movement is straight to or away from the

movement detector, the detection area is con-

siderably reduced (see Fig. C).

Installation of the light (see Fig. A)

Loosen the screw 1on the connector box,

press the release button 3and then remove

the mounting plate 4.

Use the mounting plate to mark the position for

the screw holes on the mounting surface.

Important: Ensure that you do not drill into

hidden cables or pipes.

Lead the power cable through the cable feed-

through

6of the mounting plate and then aﬃx

the plate to the wall, using screws 5and wall

plugs 7.

Then connect the power cable to the screw ter-

minal 2according to Fig. A. (N = blue cable,

earth symbol = green/yellow cable, L = brown

cable).

Reﬁt the light body to the mounting plate. To do

so, press the release button 3and push the

light onto the mounting plate until the release

button snaps into place 3again. Secure the

connection with the screw on the connector

box 1. Adjust the desired light direction and

tighten the screws.

Switch mains power back on.

Only for model L2705 PIR (see Fig. D):

Setting the timer (TIME):

The length of time the light stays switched on after

activation can be adjusted to between 10 (±5) sec-

onds a

nd 4 (±1) minutes. The time span can be short-

ened by turning the TIME control from (+) to (-).

Note: Once the light has been triggered by the

movement sensor, the time span starts anew with

every new detection.

Light adjustment (LUX):

The LUX control module features an integrated

scanner (photocell), which can diﬀerentiate

between day light and darkness. The symbol

denominates that the movement sensor is triggered

day and night, where as the symbol means that

it only reacts at night.

Sensitivity (SENS):

Sensitivity means the maximum area where the

movement sensor is triggered by movements. Turn-

ing the SENS-control from (+) to (-) decreases the

sensitivity.

Setting the control (see Fig. D)

Set the LUX-control to the symbol and wait

for half a minute until the control cycle is stabi-

lised. When doing so, ensure that the TIME-con-

trol is set to minimum (-). The light switches on

and stays on for a few seconds.

Now adjust the movement sensor in such a way

that the desired area is included.

Get someone to run through the area to be

scanned and adjust the sensor angle until the

appliance registers the presence of the person

by switching the light on (see Fig. C).

Switch the TIME-control to the desired activation

time.

In order to adjust the LUX threshold, where the

light switches on automatically during the night,

turn the LUX-control from daylight to night.

Note: Should it be necessary to switch the

light on earlier, i.e. at dusk, wait for the desired

light level, turn the LUX-control direction daylight

position, while someone runs through the middle

of the detection area.

Let go of the LUX-control

once the light is switched on.

LED-Leuchte_Content_L2705–2705 PIR_EU.indd 9 07.01.13 08:46

10 GB

Maintenance and Cleaning

The LED spotlight does not contain any serviceable

components. The LEDs cannot be exchanged.

Please only use a dry or damp cloth for cleaning

and do not use solvents, acidic cleaners etc.

Disposal

Dispose of electrical goods in an environ-

mentally friendly way!

Do not dispose of electrical equip-

ment in the household waste!

In accordance with European Directive

2002/96/EC relating to old electrical and elec-

tronic appliances, used electrical equipment must

be collected separately and recycled in an ecologi-

cally compatible way.

Contact your local authorities for information on

how to dispose of the appliance at the end of

product life.

Manufacturer

Hugo Brennenstuhl GmbH & Co. KG

Seestraße 1-3 · 72074 Tübingen · Germany

H. Brennenstuhl S.A.S.

F-67460 Souﬀelweyersheim

lectra-t ag

Blegistrasse 13 · CH-6340 Baar

For further information, we recommend you visit the

service section / the FAQs on our homepage

www.brennenstuhl.com

Problem Possible cause Recommended solution

Light does not switch

on for movements in

the detection area.

1. No grid power Please check all connections and fuses /

switches.

2. Lighting close by is too bright. Please reposition the motion detector newly

or change mounting area.

3. Control set wrongly. Reset sensor angle or readjust control.

Light switches itself on

for no obvious reason

(wrong trigger)

1. Heat sources such as air condi-

tion units, ventilation openings, out-

lets from heating units, barbecues,

other outside lights or passing cars

activate the movement sensor.

Align the sensor head away from these sources.

2. Animals / birds or pets. A new alignment of the sensor head can be

helpful.

3. Reﬂections from swimming

pools or other reﬂecting surfaces.

Realign movement sensor.

Note: All devices with a PIR sensor react more sensitively in colder weather than in

warm weather.

Troubleshooting and user notices

LED-Leuchte_Content_L2705–2705 PIR_EU.indd 10 07.01.13 08:46

Andere Handbücher für L2705

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere brennenstuhl Arbeitsleuchte Handbücher

brennenstuhl

brennenstuhl JARO Bedienungsanleitung

brennenstuhl

brennenstuhl Jet Light 55 W IP 54 Bedienungsanleitung

brennenstuhl

brennenstuhl ML CN 110 IP65 Bedienungsanleitung

brennenstuhl

brennenstuhl professionalLINE ORUM 5050 M Bedienungsanleitung

brennenstuhl

brennenstuhl ML CA110 M DE 4113 Bedienungsanleitung

brennenstuhl

brennenstuhl CAL 1 Bedienungsanleitung

brennenstuhl

brennenstuhl ML CN 110 V2 IP65 Bedienungsanleitung

brennenstuhl

brennenstuhl HL 0400 A Bedienungsanleitung

brennenstuhl

brennenstuhl SOL 04 PLUS Handbuch

brennenstuhl

brennenstuhl 1 17260 0 Bedienungsanleitung

brennenstuhl

brennenstuhl professionalLINE LB 5000 Bedienungsanleitung

brennenstuhl

brennenstuhl ML SN 4005 V2 IP 54 Bedienungsanleitung

brennenstuhl

brennenstuhl ML 130 IP54 Bedienungsanleitung

brennenstuhl

brennenstuhl HL DA 6 DM2H Bedienungsanleitung

brennenstuhl

brennenstuhl SOL 80 Handbuch

brennenstuhl

brennenstuhl SOL 80 Handbuch

brennenstuhl

brennenstuhl L2705 Bedienungsanleitung

brennenstuhl

brennenstuhl ML CA 120 F IP54 Bedienungsanleitung

brennenstuhl

brennenstuhl HL DA 40 MH DE 4113 Bedienungsanleitung

brennenstuhl

brennenstuhl Jet-Light ELH 21 Bedienungsanleitung

brennenstuhl

brennenstuhl professionalLINE LB 3000 Bedienungsanleitung

brennenstuhl

brennenstuhl LDN 2405 IP44 Bedienungsanleitung

brennenstuhl

brennenstuhl professionalLINE LA 4000 Bedienungsanleitung

brennenstuhl

brennenstuhl SHL DA 54 S IP 54 Bedienungsanleitung

Beliebte Arbeitsleuchte Handbücher anderer Marken

ANSMANN

ANSMANN POWERLIGHT 5.1 Bedienungsanleitung

RTRMAX

RTRMAX RTX1868 Bedienungsanleitung

FeinTech

FeinTech LAL00220 Bedienungsanleitung

Bunker Hill Security

Bunker Hill Security 64735 Bedienungsanleitung

Goobay

Goobay 30450 Bedienungsanleitung

REV Ritter

REV Ritter SPOT Bedienungsanleitung

Ignition

Ignition Stagepix Line 100 IP Bedienungsanleitung

SCANGRIP

SCANGRIP DUO CONNECT Bedienungsanleitung

Bosch

Bosch GLI 18 V Bedienungsanleitung

Bayco

Bayco SL-1514 Bedienungsanleitung

EUFAB

EUFAB SMD LED 8+1 Bedienungsanleitung

DeWalt

DeWalt DCL510 Bedienungsanleitung

PowerSmith

PowerSmith PWLD080T Bedienungsanleitung

MaxLite

MaxLite 73683 Bedienungsanleitung

Heitronic

Heitronic Trend 27867 Bedienungsanleitung

Monzana

Monzana Gore MZCL10 Bedienungsanleitung

EINHELL

EINHELL TE-CL 18/2000 LiAC Bedienungsanleitung

Bayco

Bayco NIGHTSTICK Dual-Light Xtreme Lumens... Bedienungsanleitung