Breville Toast & Melt LSG525 Bedienungsanleitung

the Toast & Melt

TM Sandwich Press

Instruction Book - LSG525/LSG545

BREVILLE

RECOMMENDS

SAFETY FIRST

At Breville we are very safety

conscious. We design and

manufacture consumer

products with the safety of you,

our valued customer, foremost

in mind. In addition, we ask

that you exercise a degree of

care when using any electrical

appliance and adhere to the

following precautions.

IMPORTANT

SAFEGUARDS

READ ALL INSTRUCTIONS

BEFORE USE AND SAVE

FOR FUTURE REFERENCE

• Carefully read all instructions

before operating the sandwich

press for the ﬁrst time and save

for future reference.

• Remove and safely discard

any packaging material and

promotional stickers before

using the sandwich press for

the ﬁrst time.

• Do not place the sandwich

press near the edge of a bench

or table during operation.

• Ensure that the surface is level,

clean and free of water, etc.

• Keep the sandwich press clear

of walls, curtains and other heat

or steam sensitive materials.

• The sandwich press must be

used on a properly grounded

outlet. If you are not sure if

the power outlets are properly

grounded, please consult your

electrician.

• Do not, under any

circumstances, modify the

power plug or use an adapter.

• Do not place the sandwich

press on or near a hot gas or

2 Breville Recommends Safety First

6 Components

7 Functions

8 Hints & Tips

9 Care, Cleaning & Storage

Contents

electric burner, or where it

could touch a heated oven. Use

the sandwich press well away

from walls.

• Provide adequate space

above and on all sides around

the sandwich press for air

circulation.

• Do not place the sandwich

press on any surface that

may be affected by heat. The

use of a heat resistant matt

under the sandwich press

is recommended on these

surfaces.

• Always operate the sandwich

press on a stable and heat

resistant surface. Do not use on

a cloth-covered surface, near

curtains or other ﬂammable

materials.

• Do not use on a sink drain

board.

• Do not touch hot surfaces. Use

the handles to lift and open the

top plate. Take care when using

the height-adjustable control.

• Do not leave the sandwich

press unattended when in use.

• Do not allow the power cord

to come in contact with the

hot cooking plates. Ensure the

power cord does not become

trapped between the cooking

plates during use and storage.

• Always keep the power cord

away from any heat source

including the accessible surfaces

of the sandwich press, and those

of other appliances nearby.

• The sandwich press is not

suitable to be used in a small

appliance enclosure. Ensure to

leave adequate space all around

the sandwich press. Minimum

space of 20cm is recommended.

• Do not place anything on top of

the sandwich press when the lid

is closed, during operation and

and when storing.

• Always switch the sandwich

press off at the power outlet,

then unplug the power cord

and allow to cool. Ensure the

unit has cooled down before

cleaning, attempting to move

the appliance, disassembling,

assembling and when storing

the appliance

• Do not use chemicals, steel

wool, metal scouring pad, harsh

abrasives, caustic cleaners

or oven cleaners to clean the

sandwich press as these can

damage the housing or the

coating of the cooking plates.

• Always remove the food from the

sandwich press with a heatproof

utensil e.g., silicone spatula or

tongs. Never use your hands.

• Do not use sharp objects or

utensils inside the sandwich

press as they may scratch or

damage the surface of the

cooking plates.

• The sandwich press is not

intended to be operated by

means of an external timer or

separate remote control system.

• Do not place the sandwich press

in direct sunlight. Colour fading

and discolouration may occur

when the sandwich press is

consistently exposed to UV light.

• Keep the exterior housing and

the non-stick cooking plates

clean. Follow the cleaning

instructions provided in this

book. Refer to Care, Cleaning

and Storage (Page 9).

CAUTION

• Do not touch hot surfaces. The

accessible surfaces will be hot

when the sandwich press is

operating and for some time

after use.

This appliance is marked with a

hot surface symbol.

WARNING

Fully unwind the power cord

from the cord wrap on base

before use.

IMPORTANT

SAFEGUARDS FOR

ALL ELECTRICAL

APPLIANCES

• Fully unwind the power cord

before use.

• Connect only to a 230V or

240V power outlet.

• Do not let the power cord hang

over the edge of a bench or

table, touch hot surfaces or

become knotted.

• To protect against electric shock,

do not immerse the power

cord, power plug or appliance

in water or any other liquid

or allow moisture to come in

contact with the part, unless it is

recommended in the cleaning

instructions.

• Children should be supervised

to ensure that they do not play

with the appliance.

• It is recommended to regularly

inspect the appliance. To

avoid a hazard do not use the

appliance if power cord, power

plug or appliance becomes

damaged in any way. Return the

entire appliance to the nearest

authorised Breville Service

Centre for examination and/or

repair.

• The appliance is not

intended for use by persons

(including children) with

reduced physical, sensory

or mental capabilities, or

lack of experience and

knowledge, unless they have

been given supervision or

instruction concerning use

of the appliance by a person

responsible for their safety.

• Any maintenance other than

cleaning should be performed

at an authorised Breville

Service Centre.

• This appliance is for household

use only. Do not use this

appliance for anything other

than its intended use. Do not

use in moving vehicles or

boats. Do not use outdoors.

Misuse may cause injury.

• The installation of a residual

current device (safety switch)

is recommended to provide

additional safety protection

when using electrical

appliances. It is advisable that

a safety switch with a rated

residual operating current

not exceeding 30mA be

installed in the electrical circuit

supplying the appliance. See

your electrician for professional

advice.

• During electrical storms,

the appliance should be

disconnected from the power

source at the wall socket to

prevent any electrical surges

that may arise during the storm

and which may inadvertently

cause damage to the appliance

and its electronic componentry.

• Always turn the appliance to

the off position by switching

off at the power outlet and

unplugging from the power

outlet

• Before cleaning, always turn the

appliance to the off position,

switch off at the power outlet,

unplug at the power outlet

and remove the power cord, if

detachable, from the appliance

and allow all parts to cool.

• Do not place this appliance on

or near a heat source, such as

hot plate, oven or heaters.

• Position the appliance at a

minimum distance of 20cm

away from walls, curtains and

other heat or steam sensitive

materials and provide adequate

space above and on all sides for

air circulation.

FOR HOUSEHOLD USE ONLY

SAVE THESE INSTRUCTIONS

Components

A. 2000W of power (LSG525)

2200W of power (LSG545)

For fast heat up and quick and even

toasting.

B. Heavy-duty stainless-steel arms

For durability and strength.

C. ‘Power’ and ‘Ready’ lights

Indicate when the sandwich press is

heating or ready to use.

D. ‘Floating hinge’ top plate

Automatically adjusts to thick or

thin sandwiches.

E. Flat, non-stick cooking plates

Premium non-stick coating for a quick

cleaning.

F. Height-adjustable control with 4 settings

(LSG525) or 7 settings (LSG545)

To accommodate open sandwich melts,

toasted sandwiches, artesian breads & wraps,

and everything in between.

G. Safety storage lock

To lock the plates closed for upright storage.

H. Non-slip feet with convenient cord wrap

on base.

LSG525 pictured

Functions

BEFORE FIRST USE

Remove any promotional materials and

packaging materials before use. Check that

the cooking plates are clean and free of dust.

If necessary, wipe over the plates with a damp

cloth.

HEIGHT-ADJUSTABLE CONTROL

Your sandwich press features a height-

adjustable control located on right-side arm

which allows the top plate to sit one of the

4 (LSG525) or 7 (LSG545) different height

positions above the bottom plate. This allows

your sandwich press to be used to toast a variety

of bread sizes and thicknesses, and also works

for open sandwich melts (see Fig 1).

Fig 1

TOASTED SANDWICH

1. Move the locking clip from the LOCK to

OPEN position, but leave the lid closed.

2. Insert the power plug into a 230V or 240V

power outlet and then turn the power ON.

The orange ‘POWER’ light will illuminate.

3. Allow the sandwich press to pre-heat with

the top cooking plate in the closed position

until the green ‘READY’ light illuminates.

4. Whilst the sandwich press is pre-heating

prepare the sandwich. When the sandwich

press has pre-heated, the 'READY' light

will illuminate. Open the top plate and

place using the handle the sandwich onto

the bottom cooking plate. Always place

sandwiches towards the rear of the bottom

cooking plate.

5. Adjust the height-adjustable control to the

setting of choice for the sandwich being

toasted. Close the top cooking plate using

the handle. Do not press down. The top

cooking plate has a ﬂoating hinge that

is designed to evenly press down on the

sandwich (see Fig 2).

Fig 2

6. Toasting should take approximately

3-5minutes. Exact toasting time will be a

matter of personal taste. It will also depend

on the type of bread and ﬁlling used.

7. When the sandwich is cooked, use the

handle to raise the top cooking plate.

Remove the sandwich with the help of a

plastic, silicone or wooden spatula. Never

use metal tongs or a knife as these can

cause damage to the non-stick coating.

8. When ﬁnished using, turn the sandwich

press off at the power outlet and allow

to cool before cleaning. See cleaning

instructions found in this book.

NOTE

• Always allow the sandwich press to pre-heat

until the green ‘READY’ light illuminates.

• The safety storage lock should not be used to

clamp down the top cooking plate when the

sandwiches are in the sandwich press. The

weight of the top cooking plate will gradually

press down the sandwich during the cooking

process.

• When using the sandwich press for the

ﬁrst time you may notice a ﬁne smoke haze.

This is caused by the heating of some of the

components. There is no need for concern.

WARNING

HOT SURFACE - The accessible surfaces

will be hot when the sandwich press

is operating and for some time after use.

NOTE

Fully unwind the cord from the cord wrap on the

base before use.

OPEN MELT SANDWICH

1. Unlock the sandwich press and turn on at the

power outlet. Allow the sandwich press to

pre-heat until the green ‘READY’ light

illuminates.

2. Open the top plate using the handle and

place the open sandwich with topping to be

melted on the bottom plate.

3. Move the height-adjustable control to a

higher height whereby the top plate sits

above, but not touching the sandwich.

4. Slowly lower the top plate until it rests on the

height-adjustable control.

5. The top plate will radiate the heat to melt

ingredients for the open melt, such as cheese.

6. Toasting melts should take approximately

6-8minutes, however, exact toasting time will

vary depending on the toppings used.

Hints & Tips

BREAD

Most types of bread can be used; white,

wholemeal, wholegrain, raisin loaf and so on.

The sandwich press is also ideal for toasting

artisan breads such as focaccia, Turkish bread,

baguettes as well as bread rolls. Raisin bread,

brioche or other sweet breads which contain a

higher sugar content will tend to brown quicker.

FILLINGS

If using fruit as a ﬁlling, try to use canned or

pre-cooked fruit as fresh fruit may produce

excessive liquid during cooking. Be careful when

biting into sandwiches that contain ﬁllings such

as cheese and tomato or jam as they retain heat

and may cause harm if eaten too quickly.

FAT-FREE TOASTING

Due to the non-stick ﬂat plate design, it is not

necessary to use butter or margarine on the

outside of your toasted snacks.

Care, Cleaning

& Storage

Before cleaning, ensure the power is switched

off and then remove the power plug from the

power outlet.

Allow your sandwich press to mostly cool before

cleaning however, the sandwich press is easier

to clean when still slightly warm.

Always clean your sandwich press after each

use to prevent a build-up of baked-on foods.

Wipe cooking plates with a soft, damp cloth to

remove food residue.

WARNING

Do not immerse any part of the Breville

sandwich press or the power cord in the

dishwasher, in water or in any other liquid.

PFOA-FREE NON-STICK COATING

Cooking on a non-stick surface minimises the

need for oil as food does not stick and cleaning

is easier. Any discolouration that may occur

will only detract from the appearance of the

sandwich press and will not affect the cooking

performance. When cleaning the non-stick

coating, do not use metal (or other abrasive)

scourers. Wash with warm soapy water and dry

thoroughly. Remove stubborn residue using a

damp cloth.

SEASON THE PLATES

Seasoning the plates occasionally, although not

necessary, may help to prevent sticking and

to make cleaning easier. To season, brush the

cooking plates with a little vegetable oil and

rub off the excess with absorbent paper. Do this

after preheating the unit.

NOTE

The cooking plates and hinges are coated with a

non-stick surface; do not use abrasive cleansers

or scourers.

WARNING

Allow the unit to cool down before attempting

to move.

STORAGE

To store your sandwich press:

1. Switch off at power outlet and unplug power

cord from the wall.

2. Allow the sandwich press to mostly or fully

cool, then clean as directed.

3. For storing, lock the cooking plates together

by sliding the height-adjustable control to

the front LOCK position (see Fig 3).

Fig 3

4. Wrap the power cord in the cord storage

area on the base (see Fig 4).

Fig 4

5. Store on a ﬂat, dry, level surface. The

sandwich press is designed to be stored

standing on its edge for space saving.

NOTE

The storage lock should not be used to clamp

down the top plate when sandwiches are in the

sandwich press.

WARNING

Do not immerse any part of your sandwich

press or the power cord in water or any other

liquid.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Breville Küchengerät Handbücher

Breville

Breville vtp130 Bedienungsanleitung

Breville

Breville 3X Bluicer Pro BJB815 Bedienungsanleitung

Breville

Breville Perfect Press BSG600 Bedienungsanleitung

Breville

Breville the Tea Maker BTM800XL Bedienungsanleitung

Breville

Breville the Hot Wok Pro BEW600 Bedienungsanleitung

Breville

Breville 800JEXL series Bedienungsanleitung

Breville

Breville Light and Fluffy LEG250GRY Bedienungsanleitung

Breville

Breville Muffin Magic MFM50XL Bedienungsanleitung

Breville

Breville FoodCycler LWR550 Bedienungsanleitung

Breville

Breville VST004 Bedienungsanleitung

Breville

Breville One Precision Poacher BEG800 Bedienungsanleitung

Breville

Breville BSG520XL Bedienungsanleitung

Breville

Breville VHB060 Bedienungsanleitung

Breville

Breville the Juice Fountain JE95 Bedienungsanleitung

Breville

Breville LMC600 Bedienungsanleitung

Breville

Breville BIA500 Bedienungsanleitung

Breville

Breville Juice Fountain JE900 Kurzanleitung

Breville

Breville Smart Oven Pizzaiolo Bedienungsanleitung

Breville

Breville ikon BKT500 Bedienungsanleitung

Breville

Breville PolyScience the HydroPro Bedienungsanleitung

Breville

Breville VHB083 Bedienungsanleitung

Breville

Breville the HydroPro Bedienungsanleitung

Breville

Breville JUICE & BLEND BJB840XL Bedienungsanleitung

Breville

Breville VST098 Bedienungsanleitung

Beliebte Küchengerät Handbücher anderer Marken

Tayama

Tayama TYG-35AF Bedienungsanleitung

AEG

AEG 43172V-MN Bedienungsanleitung

REBER

REBER Professional 40 Benutzerhandbuch

North American

North American BB12482G / TR-F-04-B-NCT-1 Bedienungsanleitung

Presto

Presto fountain popper Bedienungsanleitung

Westmark

Westmark 1035 2260 Bedienungsanleitung

Zanussi

Zanussi ZCG64396XA Bedienungsanleitung

HOFFEN

HOFFEN SM-9302M Bedienungsanleitung

Philips

Philips HD3133 Bedienungsanleitung

Ronco

Ronco Beef Jerky Bedienungsanleitung

Hendi

Hendi 470411 Bedienungsanleitung

Livoo

Livoo MEN386 Bedienungsanleitung

croydon

croydon WR-10313-700 Bedienungsanleitung

Chefman

Chefman RJ43-SQ Series Bedienungsanleitung

Vacmaster

Vacmaster VP680 Bedienungsanleitung

Jetmaster

Jetmaster 900HG Bedienungsanleitung

Küppersbusch

Küppersbusch EEH 610.0 Kurzanleitung zur Einrichtung

HURAKAN

HURAKAN HKN-F10 Bedienungsanleitung