BA201.Breadcrumber 5/17
Description
The OMABG80 is constructed of stainless
steel and anodised aluminium. Designed
to crumb bread up to 80kg per hour.
The machine is made up of 3 main
components.
1. Product cylinder
2. Output chute
3. Motor housing (base)
Before using the OMABG80
WARNING: Before using the OMABG80
please read the operator manual.
1. Before using the OMABG80 we
recommend that you clean all exposed
surfaces with a soft cloth that has
been placed in clean warm water and
light detergent and squeezed dry.
This will remove any traces of
machine oil, dirt or grit picked up
during manufacture or storage.
2. Ensure that the OMABG80 is
positioned on a solid and flat surface,
and at a height that allows the
operator to load the product cylinder.
3. Ensure that the product cylinder and
output chute are locked in place.
4. Ensure that a suitable container
or dish is positioned beneath the
machine to collect the breadcrumbs.
Operating the OMABG80
WARNING: Before using the OMABG80
check the electrical connections are not
damaged.
1. Connect to power using the powercord
supplied.
2. Lift the product cylinder lid and insert
bread (day old bread is recommended)
then lower lid.
3. Turn the switch to the 1 position to
activate operation.
4. Once crumbing has concluded turn the
switch back to the 0 position to turn
the machine off.
Note: No.1 position on the left is anti-
clockwise and No.1 position on the
right is clockwise. Should a blockage
occur simply turn the switch to the
opposite No.1 position to unblock.
Using and maintaining the OMABG80 Breadcrumber
OMABG80 Overload Switch
Note: The machine is equipped with an
overload switch located under the base
of the motor housing the protects the
motor in the event of undue stress.
1. If the overload switch is activated
the machine will stop. To restart the
machine it is necessary to disconnect
the machine from the main power
supply.
2. Reposition the switch to 0.
3. Using protective gloves carefully
remove the cause of the blockage
(this may involve disassembling the
breadcrumber).
4. Once blockage is cleared wait
approximately 10 seconds.
5. Push the overload switch to
re-activate the motor protector.
6. Plug machine back into power source
and re-load product into the product
cylinder and recommence operation.
Cleaning the OMABG80
Note: All cleaning and maintenance
operations must be carried out wearing
protective gloves.
1. Disconnect the machine from the
main power supply (we recommend
that you check the electrical cable
at regular intervals for wear or
damage).
2. Disassemble the product cylinder
and the output chute from the motor
housing by unscrewing the knobs
either side of the product cylinder.
Unscrew knobs either side of the
product chute to release.
3. Clean all exposed surfaces with a soft
cloth that has been placed in clean
warm water and light detergent and
squeezed dry.
4. The machine must be cleaned once a
day or more frequently if necessary.
You should never hose down
or spray with water any
component of this machine or
its environment.
You should never immerse the
machine into water.
OMABG80 Components
OMABG80 ON/OFF Switching
1. ON/OFF Switch
2. Overload Switch (under Motor Housing)
3. Product cylinder release knobs (either side)
4. Product chute release knobs (either side)
5. Product cylinder lid
6. Product cylinder
7. Output chute
8. Motor housing (base)
1
2
3
5
6
7
8
4
1 1
0
1
3
2
1. Product cylinder
2. Output chute
3. Motor housing (base)
SPECIFICATIONS
Motor 240V, 50Hz, 850w
Dimensions (mm)
Width 250
Depth 250
Height 580
Net weight (kg) 17
BRICE HEAD OFFICE:
11 Holloway Drive,
Bayswater, Victoria 3153 Australia
Ph: 1300 664 880
www.briceaust.com.au
Brice Australia Pty. Ltd. ABN 71 413 589 669
100% Australian owned and operated
Copyright ©2017 Brice Australia Pty. Ltd.
