Brighter Smart 1000 Bedienungsanleitung

Smart 1000

Spot-Beam-Wash

This product manual contains important information about the

safe installation and use of this projector. Please read and follow

these instructions carefully and keep this manual in a safe place

User manual

Please read the instructions carefully before use

TABLE OF CONTENTS

1. Safety Instructions..........................................................................................................................................3

2. Unpacking.......................................................................................................................................................4

3. Features & Specifications ...............................................................................................................................4

5. Operating Instructions....................................................................................................................................5

6. Installation......................................................................................................................................................5

7. DMX-512 Control Connections.......................................................................................................................7

8. Menu Operations ...........................................................................................................................................7

9. DMX Channels ..............................................................................................................................................10

10. Maintenance and Cleaning.........................................................................................................................19

STATEMENT

The product has full capability and intact packing when it leaves factory. All the users

should comply with provided warnings and manual. Any damages caused by misuse are

not included in our guarantee. We cannot be responsible for any malfunctions & problems

owing to ignoring the manual.

1. Safety Instructions

Please keep this User Guide for future consultation. If you sell the unit to another user, be

sure that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

Make sure there are no flammable materials close to the unit while operating as it is fire

hazard.

Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but

always by taking its base.

Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is

higher than this Unit surface temperature may reach up to 85℃.

DO NOT touch the housing bare-hands during its operation. Turn off the power and allow

about 15 minutes for the unit to cool down before replacing or serving.

In case of serious operating problem, stop using the unit immediately. Never try to repair

the unit by yourself. Repairs carried out by unskilled people can lead to damage or

malfunction. Please contact the nearest authorized technical assistance centre. Always use

the same type spare parts.

DO NOT touch any wire during operation as high voltage might be causing electric shock.

Warning:

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

DO NOT open the unit within five minutes after switching off.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly

damaged.

Caution:

There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any

repairs by yourself. If your unit requires service, please contact your nearest dealer.

Installation:

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

fixed to avoid vibration and slipping while operating. And make sure that the structure to which you

are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Always

use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at the safe place where it is not

available for other people.

2. Unpacking

Please carefully unpack it when you receive the fixture and check whether it is damaged during the

transportation. And please check whether the following items are included inside the box:

1 x User manual

2 x bracket

1 x DMX cable

1 x power wire

1 x warranty card

3. Features & Specifications

Lamp: 280W (Colour temperature: 8000K)

Channel mode: 16 / 24 DMX512 Channel

Pan scan：540°(16bit) Electric correction

Tilt scan：270° (16bit) Electric correction

Amazing dot matrix, four tact switch, 180° turning show

Colour wheel: one colour wheel, 13 kinds of colour chips in one colour wheel

Static Gobo: 10 gobos

Rotation Gobo:9 gobos

Effect Wheel: one Rotation eight prism one Rotation six prism effect move , frost

0-100% mechanical dimming, mechanical dimming and free dimming available.

strobe macro control available.

Lens optical system mechanical focus, beam angle 3.8°-45°

Over heat protection

Power Input: 100-240V，50/60Hz

Power Dissipation: 420W

IP level: IP20zgd

Magnetic ballast and AC/Dc power supply

Packing Size: 523x337x570mm

Net weight：20 KG

5. Operating Instructions

The moving head is for spot effect for on-site decoration purpose.

Don’t turn on the fixture if it’s been through severe temperature difference like after

transportation because it might damage the light due to the environment changes. So make

sure to operate the fixture until it is in normal temperature.

This light should be keep away from strong shaking during any transportation or movement.

Don’t pull up the light by only the head, or it might cause damages to the mechanical parts.

Don’t expose the fixture in overheat, moisture or environment with too much dust when

installing it. And don’t lay any power cables on the floor. Or it might cause electronics shock

to the people.

Make sure the installation place is in good safety condition before installing the fixture.

Make sure to put the safety chain and check whether the screws are screwed properly when

installing the fixture.

Make sure the lens are in good condition. It’s recommended to replace the units if there are

any damages or severe scratch.

Make sure the fixture is operated by qualified personnel who know the fixture before using.

Keep the original packages if any second shipments is needed.

Don’t try to change the fixtures without any instruction by the manufacturer or the

appointed repairing agencies.

It is not in warranty range if there are any malfunctions from not following the user manual

to operate or any illegal operation, like shock short circuit, electronic shock, lamp broke, etc.

6. Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

fixed to avoid vibration and slipping while operating. And make sure that the structure to which you

are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Always

use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at the safe place where it is not

available for other people.

Rigging (Optional)

This equipment can be positioned and fixed by clamp in every direction of the stage. Locking

system makes it easy to fasten to the bracket.

Attention! Two clamps are needed to fix the equipment. Every clamp is locked by fastener of 1/4

kind. Fastener can only be locked clockwise.

Attention! Fasten a safety string to the additional hole of the side aluminium piece. The secondary

accessory cannot hang on the delivery handle. Nip the equipment on bracket.

Check if rigging clamp (not including the one inside) is damaged or not and if it stands ten

times weight as the equipment. Make sure the architecture can stand ten times weight as all

the equipment, clamps, wiring and other additional fixtures.

Screws for clamping must be fixed firmly. Take one M12 screw (Grade 8.8 or higher) to

clamp bracket, and then screw the nuts.

Level the two hanging points at the bottom of clamp. Insert fastener to the bottom, lock the

two levers by 1/4 rotating clockwise; then install another clamp.

Install on safety string which stands at least ten times weight as equipment. Terminal of the

accessory is designed for clamps.

Check if pan/tilt lock is unlocked or not. Keep the distance more than 1m from equipment to

flammable materials.

7. DMX-512 Control Connections

This product accepts the international standard DM 512 ( 1990) of the digital control signal.

Please use the 3 pin or 5pin XLR plugs&socket offed by factory to connect the first projector’s input to

the second projector output, and connect the second projectors output to the third projectors input

and so on. Eventually connect the last projectors output.

The projectors control signal output or input by using the 3 or 5 pin XLR pug and socket. If need to

lengthen the communication cable(standard meter is 2 meters),please make sure the both side of 3 or 5

pin plug is one to one.(one to one, two to two, three to three ).Otherwise ,the communication cable will

be interrupted. The communicate cable is 2-cord screened cable 75Ω resistance with each core having

at least a 0.5mm diameter.

It is highly recommend to use the DMX signal terminator for the installation to avoid the electronic noise

damage the digital control signal. Simply speaking, DMX terminator is an XLR CINNEXTOR WITH A 120Ω

1/2 W resistor connected across pin 2 and 3. Which is plugged into the output socket on the last projector

in the chain. See illustrations below:

8. Menu Operations

DMX Address

001-512

Run mode

DMX 16 Channel

DMX 24 Channel

Auto Run

Sound Control

Master/Slave mode

Light Switch

Sure

Channel Qty

Simple

expand

Display settings

Language

中文

English

Screen saver

Mode 1

Mode 2

Mode 3

Screen Rotation

Off

Touch rectify

Test

Pan

Tilt

Focus

Colour

Gobo

Prism

Frost

Strobe

Advanced setup

Pan invert

Off

Tilt invert

Off

P/T rectify on

Off

Pan Offset

Tilt Offset

Lamp up when

Reset done

Power on

Manual

Factory setting

Sure

Statue setup

Work mode

Address

Version

Elapse

Total

DMX clr

Sys Rst

Function Mode

1. Set DMX Address

Click and select the "ADDR", you can enter the page of DMX address setting, range from 1 to 512,

the address code should not be greater than 512- channels quantity, otherwise the light will not

been controlled.

Enter the page of DMX address, click the blank area in right side of display.

Pop-up diglog will appear, as in Fig. 4. Modify value, then click ‘ENTER’ to confirm and save DMX

address code.

2. Set Light work mode

Enter the page of ‘WORK MODE’ and modify settings. You can set light work mode, control lamp

and DMX channel mode.

Light includes 3 working modes: DMX MODE, AUTO RUN and SOUND MODE.

Parameters are defined as following:

DMX Mode：When using this mode, the light receives data from DMX controller and move.

AUTO RUN：When using this mode, light will run with inside code(data), ignoring data from

DMX controller.

SOUND Ctrl：When using this mode, light ignores data from DMX controller. When there is a

strong sound in stage, the light will run a scene, otherwise it will keep the last scene.

M/S Choose ：M/S Choose’ is available when light is in ‘AUTO RUN’ or ‘SOUND Ctrl’ mode. If

this item is set as ‘OFF’, the light don’t send data to other light via DMX Cable. When it is

‘ON’, the data will be sent to other slave light immediately.

Lamp control：Turns on lamp when this item is set ‘ON’, otherwise, turns off lamp. The gap

between operation is limited to 30 second.

Channel mode：Light support 2 DMX Channel mode: sample or extend。

3. Set display

Light supports 2 language, display rotation.

Language：Select display as simplified Chinese or English.

Screen Saver：when panel is idle ( there is no operation in 10 second ), display will enter

saver status. When it is set as ‘mode 1’，saver status is close display, as ‘mode 2’ saver

status will display DMX address code(DMX MODE) or display LOGO(AUTO RUN or SOUND

CTRL). As ‘OFF’, keep light up display and show main menu.

Screen Rotation：rotate display.

Touch enable：Disable or enable touch function, when disable, use encoder to operate light

and set parameter.

Touch adjust：adjust touch function, normally, not enter this item.

4. Test light

Enter the page , Light will go into test mode, in this mode, the light does not receive the data from

DMX controller.

PAN: range for 0 to 255;

TILT: range for 0 to 255

FOCUS: range for 0 to 255

COLOR: range for 0 to 255

GOBO: range for 0 to 255

PRISM: range for 0 to 255

FROST: range for 0 to 255

STROBE: range for 0 to 255

5. Set light run parameters

Enter the page, set the parameter of light:

Pan Invert: Reverse PAN move.

Tilt Invert: Reverse TILT mover.

Rectify enable：set as ‘OFF’, PAN or TILT will disable position rectify function.

As ‘ON’, when PAN or TILT lose steps, light will rectify auto.

Pan Offset: Set PAN original position.

Tilt Offset: Set TILT original position.

Lamp up when: Select lamp on mode, includes 3 mode: “power on”, “after reset done” and

“manual”.

Factory setting: restore all parameter to factory setting.

6. View status

View light current status, version；

DMXClr: Click to clear all DMX data to ‘0’.

SysRst：Click to reset light.

9. DMX Channels

CH NO

Name

value

Function

CH1

0-255

Pan movement by 540°

CH2

0-255

Tilt movement by 270°

CH3

XY speed

Max. speed (tracking mode)

1-255

Speed from max. to min. (vector mode)

CH4

power/macro

0-129

empty

130-139

Lamp On,reset(total reset except pan/tilt reset)

140-149

Pan/Tilt reset

150-189

Effect motor reset

190-199

Reserved

200-209

Total reset

210-229

Reserved

230-239

Lamp Off

240-255

Reserved

CH5

Color wheel

0-8

Open/white

9-17.

Deep Red

Inhaltsverzeichnis

Andere Brighter Leuchte Handbücher

Brighter

Brighter Eye 360 Led Bedienungsanleitung

Beliebte Leuchte Handbücher anderer Marken

Emos

Emos CLASSIC ZY1431T Bedienungsanleitung

Westinghouse

Westinghouse Outdoor Lighting Fixture Bedienungsanleitung

Hedler

Hedler C 12 silent Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Puck: CSI Bedienungsanleitung

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Bedienungsanleitung

Lightmaxx

Lightmaxx Shaft 5R Bedienungsanleitung

Triarch

Triarch 31083 Bedienungsanleitung

Philips

Philips 32614 Series Bedienungsanleitung

IKEA

IKEA TIVED Bedienungsanleitung

Lightolier

Lightolier LP200 Bedienungsanleitung

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Bedienungsanleitung

Martin

Martin MAC 250 Krypton Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo L3232E Bedienungsanleitung

Stageline

Stageline ODW-2410RGBW Bedienungsanleitung

Light Sky

Light Sky Tornado Series Bedienungsanleitung

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Bedienungsanleitung

Lightolier

Lightolier Lytespan 83ED17S Bedienungsanleitung

Lightolier

Lightolier Calculite CS8226 Bedienungsanleitung