BriteLite M2000 Bedienungsanleitung

OPERATIONS MANUAL –M2000

Professional ABS Molded Loudspeaker

Introduction:

Congratulations on your purchase of an M-2000 powered loudspeaker, engineered and

manufactured by BriteLite Enterprises. The M-2000 includes a high-output compression driver,

and 15” woofer to produce an even, smooth studio quality sound in a sound reinforcement

speaker. Our design goal was to build a speaker with accurate playback, smooth dispersion of

mid and high frequencies and an ergonomic design for easy transport and setup. The result is a

sound reinforcement system dynamic enough to use at home, in the studio, parties or in home

theater.

Features:

2-way Bi-amplified Active Speaker

15” Long-throw woofer with high-

temperature voice coil

Ultra-wide, smooth dispersion of

high and mid frequencies

Mic/Line input and pass-thru

connector

USB & SD Card input supports

.wav & MP3

Bluetooth Compatible

Includes FM Radio w/Antenna

Multi-function remote control

Stand/Pole-mountable

Cautions:

1. All Operating Instructions should be read before using this equipment.

2. To reduce the risk of electrical shock, do not open this unit. There are NO

REPLACEABLE PARTS INSIDE. Please refer servicing to a qualified service technician.

3. Do not expose this unit to direct sunlight or to a heat source such as a radiator or stove.

4. This unit should only be cleaned with a damp cloth. Avoid solvents or other cleaning

detergents.

5. When moving this equipment, it should be placed in its original carton and packaging.

This will reduce the risk of damage during transit.

6. DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

7. DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY CONTROLS OR

SWITCHES

8. Make sure all of your equipment is completely OFF and lower ALL VOLUME, LEVEL &

GAIN controls before connecting a sound source.

9. Only LINE LEVEL SIGNALS SHOULD BE SENT TO YOUR SPEAKER.

Failing to adhere to the cautions above will void the manufacturer warranty!

OPERATIONS MANUAL –M2000

Professional ABS Molded Loudspeaker

Functions:

1. USB Port

2. SD/MMC Port

3. LCD Display

4. Press this button to PAUSE. Press for 2-3 seconds to return to the

5. Press this button to return to the start of the previous track

6. Press this button to skip to the beginning of the next track.

7. Mode button, to switch between USB/SD or FM/Bluetooth function. Press

for two to three seconds to select EO/PLAY MODE/LANGUAGE. When

paused in USB/SD mode, press button for two or three seconds to select

a folder, then select the audio file.

8. Press to raise the Digital Audio Player’s volume. In folder mode, press to

skip to the previous page.

9. Press to lower the Digital Audio Player's volume. In folder mode, press to

skip to the previous page.

10. MIC IN: Use XLR or 1/4" jack connector balanced or unbalanced.

11. LINE IN: Use RCA or XLR connector balanced or unbalanced.

12. LINE OUT: Use this connector to daisy-chain several active speakers

together from the same signal source.

13. MIC LEVEL: Control the output volume when using a microphone.

14. LINE LEVEL: Control the output volume for LINE level inputs.

15. MASTER: Controls the output volume.

16. TREBLE: Raise or attenuate highs at 12dB @ 12 KHz frequency.

17. BASS: Raise or attenuate lows at 12dB @ 80Hz frequency.

18. PEAK: LED illuminates when a clipped signal is present. Reduce volume

to avoid distorted sound.

19. Power Indicator

20. Power Supply Switch

21. Voltage Selector: Adjust AC Power between 115V and 230V

22. Power Supply Input Connector: Use with power cord.

23. FM RADIO with antenna.

24. Remote Control

Warning:

Make sure speaker is off and all LEVEL controls are down (counterclockwise) before every

use.

Connections:

1. Connect the output from your signal source (mixing console, microphone, preamp, or other mic- or

line-level source) directly to the INPUT connector on the back of the speaker. It accepts balanced

line-level signals from mixers, preamplifiers, CD players, tape decks, etc., and accepts direct

connections from dynamic microphones through the MIC input.

2. There is also a 1/4” and XLR Output connector labeled LINE OUT. This allows you to connect more

than one M-2000 to the output of your sound source. Simply plug a ¼” or XLR cable from the Line

Out connector of one speaker to the input connector of another speaker, and so on, daisy-chaining

multiple speakers.

3. Turn on your signal source. (Make sure volume is turned down) Turn on M-2000. Start signal

source and adjust volume controls on the signal source and M-2000 speaker.

OPERATIONS MANUAL –M2000

Professional ABS Molded Loudspeaker

Bluetooth Connection

1. Make sure device (iPod, MP3 player, etc.) Bluetooth function is enabled. Remove SD Card or USB

stick from speaker before enabling Bluetooth.

2. On the speaker, press and hold menu (4) button for 2-3 seconds to call up main menu. Press

NEXT (6) button to select Bluetooth function and press MENU (4) button again to activate

Bluetooth. Your device and speaker should now be connected.

3. Make sure to choose BLUETOOTH from your device to complete the connection

4. Only one Bluetooth device can be connected to the M2000 speaker at a time.

5. To connect a new device; turn off the M2000 speaker for 10 seconds and turn on again and begin

with step one above.

Placement Tips

Avoid placing loudspeakers in the corners of a room. This increases the low-frequency output and can

cause the sound to be muddy and indistinct.

Avoid placing loudspeakers against a wall. This, too, increases the low frequency output, though not as

much as corner placement. However, if you do need to reinforce the low frequencies, this is a good way

to do it.

Avoid placing the active speakers directly on a hollow stage floor. A hollow stage can resonate at

certain frequencies, causing peaks and dips in the frequency response of the room. It’s better to place

the speakers on a sturdy table or tripod stands.

Position the speakers so the high-frequency drivers are two to four feet above ear level to the audience

to maintain high frequency quality.

Troubleshooting

No Power

First check to make sure the speaker is plugged in to a live AC outlet.

Make sure the POWER switch is on.

No Sound

Make sure input LEVEL control turned up.

Make sure signal source is working and the connecting cables are in good shape and securely

connected at both ends. Make sure the output volume control on the mixing console is turned up.

Make sure the preamp or mixer does not have a Mute button engaged.

Bad Sound –Noise - Humming

If the sound is loud and distorted, verify that the levels are set properly on the speaker and mixing

console.

Make sure all connectors are secure and they are plugged in to the proper connecter (i.e., Mic cable

plugged in to MIC input, Line level source plugged in to Line Level Input.

It is a good idea to periodically clean all electrical connections with a non-lubricating electrical contact

cleaner.

OPERATIONS MANUAL –M2000

Professional ABS Molded Loudspeaker

Make sure none of the signal cables are routed near AC cables, power transformers or other electrical

power cords.

If humming occurs, turn the LEVEL control of the speaker all the way down. If the noise disappears, it’s

coming from the signal source. If not, try disconnecting the cable connected to the INPUT jack. If the

noise disappears, it could be a “ground loop,” Try the following ideas:

oUse balanced connections throughout your system for best noise rejection. (XLR cables,

balanced ¼” jacks; RCA cables are not balanced)

oWhenever possible, plug all the audio equipment’s power cords into the same outlet.

oThe hum may appear when using an unbalanced source (CD player, iPod, etc.). You

can use an RCA to XLR adapter to turn an unbalanced cable to a balanced cable.

oIf the hum persists, try removing components one at a time from the back of the mixer

and check each for hum. Reducing the Bass or Treble levels (16 and 17) may reduce

humming.

Care and Maintenance

Your active speakers will provide many years of reliable service if you follow these guidelines:

Avoid exposing the loudspeaker to moisture. If they are set up outdoors, be sure they are under

cover if you expect rain.

Avoid exposure to extreme cold. If you must operate loudspeakers in a cold environment, warm

up the voice coils slowly by sending a low-level signal through them for about 15 minutes prior

to high-power operation.

Use a dry cloth to clean the cabinets. Only do this when the power is turned off. Avoid getting

moisture into any of the openings of the cabinet, particularly where the drivers are located.

Limited Warranty

This Limited Product Warranty is provided by BriteLite Enterprises. BriteLite warrants to

Customer that the product is free from defects in materials and workmanship under normal use

during the Warranty Period (the dealer that sold the speaker can provide the warranty period

information). If the product fails to conform to the warranty then BriteLite or its authorized

service will either repair or replace any nonconforming product, provided that Customer gives

notice of noncompliance within the Warranty Period to BriteLite by emailing [email protected]

or calling 310-363-7110 (Mexico customers can call 0155 4624 0251). Please retain the original

dated receipt as evidence of proof of purchase.

Inhaltsverzeichnis

Andere BriteLite Sprecher Handbücher

BriteLite

BriteLite HC-1202F Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung