Broadcast Tools SS 16.16 Bedienungsanleitung

Installation and Operation Manual

Due to the dynamic nature of product design, the information contained in this

document is subject to change without notice. Broadcast Tools, Inc., assumes no

responsibility for errors and/or omissions contained in this document. Revisions

of this information or new editions may be issued to incorporate such changes.

Broadcast Tools® is a registered trademark of Broadcast Tools, Inc.

No part of this document may be reproduced or distributed without permission.

Visit www.broadcasttools.com for important product update information.

Firmware Version 1.1 or greater

Manual Revised 03/25/08

SS 16.16

Sixteen Input, Sixteen Output Stereo Audio Routing Switcher

INC

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742

SS 16.16 Installation and Operation Manual

Table of Contents

Section Title Page #

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Who to Contact for Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Product Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Audio Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Audio Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

ACT Audio Activity Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

PIP Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Open Collector Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Serial Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

User Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Operation Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Front Panel Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Selecting Input/Output channel . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Power-Up Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Macro Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Monitoring audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

CONTENTS

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742

SS 16.16 Installation and Operation Manual

Table of Contents – cont’d

Installation Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Setting Operation “Dip” Switches . . . . . . . . . . . . . . . . . . . . . . . . 11

Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Power Supply Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Connecting Inputs/Outputs/Open Collectors . . . . . . . . . . . . . . . . 13

Adjusting Input and Output Levels . . . . . . . . . . . . . . . . . . . . . . . 13

Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Connecting the RS-232 Serial Port. . . . . . . . . . . . . . . . . . . . . . . . 14

Connecting Two Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Serial Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Menu Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Serial Burst Mode Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Set-up Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Real Time Control Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Open Collector Output Port Control. . . . . . . . . . . . . . . . . . . . . . . 17

Audio Switch Control Commands . . . . . . . . . . . . . . . . . . . . . . . . 17

Information Retrieval Commands . . . . . . . . . . . . . . . . . . . . . . . . 17

Open Collector Status Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

“PIP” with Programmable Pulse Stretcher . . . . . . . . . . . . . . . . . . 18

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

CONTENTS

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742

SS 16.16 Installation and Operation Manual

INTRODUCTION

Thank you for your purchase of a Broadcast Tools® SS 16.16 Sixteen Input,

Sixteen Output Stereo Audio Routing Switcher (referred to as the SS 16.16

throughout this manual). We’re confident that this product will give you many

years of dependable service. This manual is intended to give you all the infor-

mation needed to install and operate the Broadcast Tools® SS 16.16.

SAFETY INFORMATION

Only qualified personnel should install Broadcast Tools® products. Incorrect or

inappropriate use and/or installation could result in a hazardous condition.

WHO TO CONTACT FOR HELP

If you have any questions regarding your product or you need assistance, please con-

tact your distributor from whom you purchased this equipment.

If you would like more information about Broadcast Tools® products, you may

reach us at:

Broadcast Tools, Inc.

131 State Street

Sedro-Woolley, WA 98284 USA

Voice: 360.854.9559

Fax: 866.783.1742

Internet Home Page: www.broadcasttools.com

E-mail: [email protected]

THANK YOU FOR CHOOSING

BROADCAST TOOLS® BRAND PRODUCTS!

CAUTION!

Broadcast Tools®

Products, as with any

electronic device, can

fail without warning.

Do not use this product

in applications where a

life threatening condition

could result due to failure.

NOTE:

This manual should be

read thoroughly before

installation and operation.

WEBSITE:

Visit our web site for

product updates and

additional information

Broadcast Tools is a Veteran Owned Business

Designed, Assembled and Supported in WA State, USA

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742

SS 16.16 Installation and Operation Manual

DESCRIPTION

The Broadcast Tools® SS 16.16 provides audio routing of 16 stereo inputs to 16

stereo outputs. This type of switching allows any one stereo input to be assigned to

any or all stereo outputs. The SS 16.16 may be controlled via front panel encoder

controls and/or multi-drop RS-232 serial port. A 40 x 4 LCD back lit display pro-

vides for input descriptions and macro setup. A 16 x 16 GPIO port is provided when

used with automation systems. FREE MS Windows “NetSwitch/II remote control

software is available for download. Two versions are provided, serial/USB and

Ethernet. Installation is simplified with removable screw terminals (Euro).

PRODUCT FEATURES

• Stereo routing of any one input to any or all outputs.

• Headphone amplifier with front panel 1/4” jack and level control.

• Front panel monitor speaker with mute switch and level control.

• 40 x 4 LED back lit LCD display with user programmable nine character

input descriptions.

• Internal audio activity/silence sensor monitors output channel sixteen. A front

panel “ACT” indicator and rear panel open collector are provided. Trigger

set at -30dbu.

• Two front panel encoder controls are provided. One each for input / output

channel selection.

• Power-up selection of channel configuration, mute or last source selected.

• Sixteen user configured macros.

• Most configuration options may be set via the easy access rear panel dip-

switches.

• 16 input GPI port (PIP) with LED indicator.

• 16 open collector channel status outputs or programmable via burst com-

mands.

• Multi-turn input level controls and single turn output level controls.

• Electronically balanced stereo inputs and outputs.

• Multi-drop RS-232 serial port with data activity LED.

• Multiple unit inputs may be cascaded to expand outputs.

• Depluggable screw (EURO) terminals for ALL connections.

• Logic functions via microprocessor with non-volatile memory.

• External tri-voltage universal switching power supply.

• 2-RU chassis.

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742

SS 16.16 Installation and Operation Manual

DESCRIPTION

PRODUCT DESCRIPTION

Front Panel:

The SS 16.16 is a 2 - RU device (19”w x 3.50”h x 10”d). The front panel supports

two encoder controls, five function switches, 5 LED indicators, 1/4” headphone

jack, monitor speaker, mute switch and level control.

Rear Panel:

Installation is simplified with pluggable screw terminal connectors. The SS 16.16

may be pre-wired and installed in minutes. The multi-drop RS-232 modular con-

nector is provided for serial operation. The 5-pin “DIN” power connector is pro-

vided along with a universal switching tri-voltage power supply. Two power LED’s

indicate +/-15 & 5 Vdc power supply operation.

Switches:

Five pushbutton switches (The “PGM” switch is hidden) that may be used to mute

or take selected audio configurations. Sixteen macros may also be programmed and

selected.

LED Indicators:

The SS 16.16’s 5 front panel LED indicators provide operational display of the fol-

lowing information:

• PGM LED, illuminates when the unit is in (menu) program mode.

• Power and serial data activity. This LED flashes when serial data is active.

• Macro indicator will light when in macro record or recall mode.

• “PIP” Parallel Input Port LED will flash indicating any change with the 16 input

“Pulse Stretcher” GPI ports.

• One audio activity LED. Monitors output channel sixteen and lights when lev-

els are above –30dbu.

Controls:

Audio Inputs: Each of the 16 stereo inputs are balanced bridging (20KΩ) at a

nominal line level of +4dBu. Multi-turn level controls are provided for each stereo

channel. Odd numbered input level controls are left of the designated connector,

while even numbered controls are right of the connector. The double-decker input

connectors are configured with the odd numbered inputs on the bottom and the even

numbered inputs on the top. If required, 600 Ωterminating resistors may be added

to the connector.

Audio Outputs: The SS 16.16 provides sixteen balanced stereo outputs. Nominal

line level at 100 ohms is set for +4dbm. Sixteen left and right output level controls

are inside the unit and are labeled “OUT#LT or OUT#RT”. Controls are single turn

and provide approximately 2db of trim. The double-decker output connectors are

configured with the odd numbered outputs on the bottom connectors, while the even

numbered outputs are on top. If required, 600 Ωterminating resistors may be added

to the connector.

WEBSITE:

Visit our web site for

product updates and

additional information

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742

SS 16.16 Installation and Operation Manual

DESCRIPTION

“ACT” Audio Activity Sensor:

The SS 16.16 contains one audio activity sensor, which may be used as a silence sen-

sor. The sensor monitors output channel sixteen. The factory default has a fixed sig-

nal threshold of -30dbu. Upon silence detection, the “ACT” indicator is extinguished

for the duration of silence and the rear panel open collector switches to ground.

When audio returns, the front panel “ACT” LED will illuminate and the open col-

lector will go into a high impedance state.

PIP Input:

The Parallel Input Port (GPI) with the Programmable Pulse Stretcher provides 16

pulse-stretched parallel 5-volt TTL/CMOS compatible inputs. The inputs are pulled

high to 5 volts through a 20KΩresistor and are activated by pulling the input to

ground. Inputs supply status to any serial polling device (when the unit ID is set

to 0, no polling of inputs is required). For all PIP inputs, a pulse of 50ms or greater

is required to go true. The pulse stretch width may be varied between 50ms and 2.55

seconds. This allows the polling computer more time to detect an input change.

Open Collector Outputs:

The SS 16.16 provides sixteen open collector status outputs. The status outputs may

be configured to operate in one of three modes:

1. The status output follows the associated channel.

2. The status outputs a one-second pulse when the associated channel is selected.

3. Software burst mode control

Serial Communication:

The SS 16.16’s serial communication may be configured for multi-drop RS-232,

allowing up to 8 - SS 16.16’s on the same computer’s serial port. Burst mode allows

a computer or ASCII terminal to control and interrogate the unit. This section

defines all burst mode commands. Each burst mode command starts with an aster-

isk (“*”). Next is a single decimal digit that corresponds to the unit (ID) address 0-

7. Following that are one or more ASCII characters specifying the command. No

carriage-return or line-feed is required to terminate the command except for those

few commands of variable length, if the maximum length is not sent. If acknowl-

edgements are enabled, successful commands are responded to with “RRR” while

errors get an “EEE” response. The syntax of each command is given in the instal-

lation section of this manual.

User Programming:

The SS 16.16 programming is stored in non-volatile memory. Configurations are set

with selection dipswitches and computer commands.

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742

SS 16.16 Installation and Operation Manual

OPERATION

OPERATION GUIDELINES

Front Panel Indicators

WEBSITE:

Visit our web site for

product updates and

additional information

Front Panel

LED’s Number

Of LED’s

Activation

Event/Mode Activation

Behavior

Pwr/Ser 1 Green Valid Power or serial

data activity On with power or

flashing with serial

data activity

“PGM” 1 Red Menu mode On if in program or

menu mode

Macro 1 Green Macro selection On if active

“PIP” Active 1 Yellow Any valid “PIP” input Blinking if active

“ACT” 1 Yellow Audio Activity for OP

16 On if active audio

“PGM” and

“MACRO” Red/Green Alternately flashing

when the front

panel is locked

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742

SS 16.16 Installation and Operation Manual

OPERATION

Front Panel Controls:

Selecting an Input/Output channel:

1. Turn the “Output Select” encoder knob until the flashing asterisk is at the

desired output channel.

2. Turn the “Input Select” encoder knob until the desired input channel is dis-

played.

3. When ready to select, press the “TAKE” button.

4. The display will stop flashing, indicating the selection has been made.

Power-Up Feature, user programmable:

1. Verify that dipswitch SW1-7 is OFF.

2. Select the desired input/output channel configuration.

3. Press the hidden “PGM” button with a non-metallic object. Macro number

will be displayed in the output-1 slot on the LCD.

4. Rotate the “INPUT SELECT” encoder knob until macro number 0 displayed.

5. Press the “TAKE” button to save.

6. Your power up configuration is saved.

Power-Up Feature, last source selected:

1. Verify that dipswitch SW1-7 is ON.

2. The SS 16.16 will power up with whatever channel configuration was present

at power off.

Controls: Function:

Input Encoder By turning this control, each input

description is displayed on the

LCD at the desired output channel.

Output Encoder By turning this knob, the cursor will

move through the output channels.

Take Switch Stores your selection

Mute Switch Mutes the selected output

Macro Either selects a macro or allows

the programming of a macro

Hidden “PGM”

Note: This switch (hole) is between

the Macro switch and PGM LED Special programming functions

Monitor/Headphone control Used to adjust the level of the

headphones and/or monitor

speaker

Speaker switch Turns the monitor speaker on/off

e-mail: [email protected] voice: 360.854.9559 fax: 866.783.1742

SS 16.16 Installation and Operation Manual

OPERATION

Macro “RECORD” Feature:

1. Select the desired input/output configuration.

2. Press the hidden “PGM” button with a non-metallic object. Macro number

will be displayed in the output-1 slot on the LCD.

3. Rotate the “INPUT SELECT” encoder knob until the desired macro number

is displayed.

4. Press the “TAKE” button to save.

Macro “RECALL” Feature:

1. Press the macro button: Macro number will be displayed in the output-1 slot

on the LCD.

2. Rotate the “INPUT SELECT” encoder knob until the desired macro number

is displayed.

3. Press the “TAKE” button.

To monitor audio with the headphone or Monitor amplifier

1. Select output 16 and the desired input.

2. Press the SPKR switch in the turn on the monitor speaker.

3. Adjust level with the Hdph/Spkr control.

WEBSITE:

Visit our web site for

product updates and

additional information

Inhaltsverzeichnis

Andere Broadcast Tools Schalten Handbücher

Broadcast Tools

Broadcast Tools AES Switcher Sentinel 2+1 Bedienungsanleitung

Broadcast Tools

Broadcast Tools SS 2.1 MLR/TERM Bedienungsanleitung

Broadcast Tools

Broadcast Tools DMS-III Bedienungsanleitung

Broadcast Tools

Broadcast Tools SS 4.2 Bedienungsanleitung

Broadcast Tools

Broadcast Tools Audio Sentinel 4 Web Bedienungsanleitung

Broadcast Tools

Broadcast Tools SS 8.1 MLR Bedienungsanleitung

Broadcast Tools

Broadcast Tools RM-3 Bedienungsanleitung

Broadcast Tools

Broadcast Tools 38511 Bedienungsanleitung

Broadcast Tools

Broadcast Tools ROS-16 Bedienungsanleitung

Broadcast Tools

Broadcast Tools Universal 4.1 MLR/Serial Bedienungsanleitung

Broadcast Tools

Broadcast Tools SS 16.2 Bedienungsanleitung

Broadcast Tools

Broadcast Tools SS 8.1 MLR Bedienungsanleitung

Broadcast Tools

Broadcast Tools Sentinel 3 Bedienungsanleitung

Broadcast Tools

Broadcast Tools ACS 8.2 Plus Bedienungsanleitung

Broadcast Tools

Broadcast Tools DAS 8.4 Plus Bedienungsanleitung

Broadcast Tools

Broadcast Tools SS 2.1 BNC Bedienungsanleitung

Broadcast Tools

Broadcast Tools Universal 4.1 MLR Bedienungsanleitung

Broadcast Tools

Broadcast Tools AES Switcher Sentinel 4 XLR Bedienungsanleitung

Broadcast Tools

Broadcast Tools ROS Bedienungsanleitung

Broadcast Tools

Broadcast Tools SS 8.1 II Bedienungsanleitung

Broadcast Tools

Broadcast Tools SS 4.1 Plus Bedienungsanleitung

Broadcast Tools

Broadcast Tools 8 x 2A Bedienungsanleitung

Broadcast Tools

Broadcast Tools SS 4.1 III Bedienungsanleitung

Broadcast Tools

Broadcast Tools AES Switcher Sentinel 4 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch