Broadxent Broadband Blaster 8012-V Bedienungsanleitung
User Manual
Broadband Blaster 8012-V
1
INTRODUCTION
Welcome to Broadband Blaster World! Your new Digital Subscriber Line (DSL) modem takes
you to a world of digital entertainment and exploration by giving you fast Internet connection
through existing telephone lines.
Creative Broadband Blaster DSL Bridge 8012-V uses the most advanced “splitterless”
Asymmetric DSL (ADSL) technology that transforms ordinary telephone lines into broadband
high-speed digital lines for fast Internet access. Broadband Blaster 8012-V is compliant with
both ITU G.Lite and G.DMT standards that provides downstream data transmission up to 8
Mbps and upstream data transmission up to 1 Mbps, depending upon your agreement with your
DSL service provider.
Broadband Blaster DSL Bridge 8012-V is equipped with an Ethernet interface
This User Manual will help you during hardware installation, as well as setting up the
computer's networking configurations. Utilizing the Windows plug-and-play feature.
This section provides you with safety instructions and information you should know before
using your Broadband Blaster DSL Bridge 8012-V:
❑Important Safety Instructions
❑Model and Serial Numbers
❑Minimum System Requirements
❑Package Contents
❑Getting Started
2
User Manual
Broadband Blaster 8012-V
Important Safety Instructions
This section provides basic safety information for your Creative Broadband Blaster DSL Bridge
8012-V modem.
Prior to using your modem, carefully read and understand the safety instructions. These
instructions must be followed to reduce the risk of fire, electric shock, or personal injury.
• Make sure that your modem is not exposed to direct sunlight or excessive heat
radiation.
• Keep your modem at a place where there is minimum risk of spilling any liquid.
• The surrounding ambient temperature must not exceed 400C (1040F).
• Avoid humid conditions. Do not place the product near a water source or outlet such as
a bath tub, sink, wash bowl, laundry tub, swimming pool, rain, wet or humid wall, and
so on.
• Never clean your modem with a damp cloth or use any liquid cleaner.
• Do not press, put any weight, or bend the power cord connected to telephone
equipment.
• To avoid risk of an electric shock during lightning, do not use any telephone equipment
that is connected to an electric socket.
• In case of a gas leak, do not use any electric switch that is located in the vicinity of the
leak.
• To report a gas leak, do not use any telephone equipment that is connected to an
electric power outlet in the vicinity of the leak.
• Do not use any electric product, electric cord, or power socket that is even partially
damaged.
• Do not expose yourself to dangerous voltages by opening the cover of your modem or
dismantling it.
• You must not access the internal assembly or circuit board of your modem — none of
its parts are user replaceable.
• Do not dispose off the batteries in fire — they may explode and cause injury. Besides,
you must follow the local codes for special disposal instructions.
• If your modem needs any service or repairs, only qualified service personnel must
handle it.
User Manual
Broadband Blaster 8012-V
3
Model and Serial Numbers
Your Broadband Blaster DSL Bridge 8012-V has model and serial numbers. You can find it on
the bottom of your modem. Note down the model and serial numbers for future reference.
Minimum System Requirements
For a proper operation of your Creative Broadband Blaster DSL Bridge 8012-V, refer to the
minimum system requirements listed below:
•Intel
®Pentium®100 MHz or equivalent processor
• Microsoft Windows®95
• 20 MB of free hard disk space
• 32 MB of RAM
• Installed Network Interface Card with an RJ-45 port
Package Contents
Before you begin hardware installation, check your Broadband Blaster 8012-V package to
ensure all the following items are available:
• Broadband Blaster DSL Bridge 8012-V unit
• One CD-ROM that contains
a) Diagnostic program ( BBUI )
b) User Manual (PDF)
c) Acrobat Reader
• Power adapter
• RJ-11 Phone cable
• RJ-45 Ethernet cable
4
User Manual
Broadband Blaster 8012-V
Getting Started
Before you begin hardware or software installation and configuration, read this section
carefully:
• You must sign up with ISP — your Internet Service Provider.
• Obtain the confirmation that the DSL Service has been enabled on your telephone line.
• For your computer connected to the Ethernet port of 8012-V, follow these steps :
“Hardware Installation”.
• If you ran into any technical issues or need clarification on certain technical terms,
please refer to the Appendix on Troubleshooting in this manual .
User Manual
Broadband Blaster8012-V
5
1. HARDWARE INSTALLATION
Creative Broadband Blaster DSL Bridge 8012-V modem is equipped with a 10/100 BaseT
Ethernet interface .
This chapter provides information about your Broadband Blaster 8012-V, as well as hardware
installation. To ensure the proper setup and performance, before you begin connecting cables
and devices to your Broadband Blaster 8012-V, you must carefully go through the following
sections:
❑Backside View of Broadband Blaster 8012-V
❑Connecting Microfilters
❑Hardware Installation
❑Indicator LEDs on Broadband Blaster 8012-V
6
User Manual
Broadband Blaster8012-V
Backside View of Broadband Blaster 8012-V
Located at the rear panel of your Creative Broadband Blaster DSL Bridge 8012-V (see Figure
1-1) are several connectors that allow you to attach your computer and a telephone equipment,
as shown in Figure 1-3.
DSL LINE jack
Using the RJ-11 phone cable, connect your DSL-enabled telephone line (the wall phone outlet)
to the DSL LINE jack located on your Broadband Blaster 8012-V.
Ethernet port
Using the RJ-45 Ethernet cable, the Ethernet port connects your Creative Broadband Blaster
8012-V to the Ethernet Network Interface Card in a PC.
Power socket
Use ONLY the supplied DC power adapter to power the Broadband Blaster 8012-V.
Reset Switch
This switch has no function during hardware installation. It is meant for restoring Broadband
Blaster 8012-V configuration settings to the default values.
Figure 1-1: Backside view of Broadband Blaster 8012-V
DSL LINE Jack Ethernet Port Reset Power Plug
User Manual
Broadband Blaster8012-V
7
Connecting Microfilters
Each analog device, such as a telephone equipment,
fax machine, or answering machine that you connect
on your DSL line requires a microfilter, as illustrated
in Figure 1-2.
1. Plug one end of a RJ-11 telephone cable into a
microfilter and connect the analog device to the
other end of this RJ-11 cable.
2. Plug the other end of this microfilter, the end that
has a RJ-11 connector, into a telephone wall
outlet.
Telephone
Microfilter
Wall Outlet
Figure 1-2
8
User Manual
Broadband Blaster8012-V
Hardware Installation
Connect your Broadband Blaster 8012-V :
Figure 1-3
Figure 1-3
User Manual
Broadband Blaster8012-V
9
Indicator LEDs on Broadband Blaster 8012-V
Indicator LEDs on Broadband Blaster 8012-V
Your Broadband Blaster DSL Bridge 8012-V features indicator LEDs which provides you with
your DSL connection status. Refer to the Figure 1-4 and Table 1-1 for the function of each LED.
Table 1-1: Description of LEDs
LED Description
POWER ON when your 8012-V is properly connected to a power source.
DIAGNOS-
TIC
ON when 8012-V performs self-test at the initial power up. Once the normal
operation is detected, the LED will remain off.
DSL Flashes for a few seconds and stays ON when a DSL connection is estab-
lished.
LAN ONwhen an Ethernet connection is detected between 8012-V Lan Port and
PC Ethernet card, Flashes when Data is transferring during access to Internet.
Broadband
Blaster
POWER DIAGNOSTIC DSL LAN
User Manual
Broadband Blaster 8012-V
10
TECHNICAL SPECIFICATIONS
This section provides certain technical specifications for the Broadband Blaster DSL Bridge
8012-V:
Data Encapsulation Protocol:
- RFC 1483 Multiprotocol Encapsulation over ATM Adaptation Layer 5
ADSL Line Interface:
- ANSI T1.413
- ITU G.992.1 (G.DMT)
- ITU G.992.2 (G.LITE)
Electrical:
- AC Adapter
Input 120 VAC, 60 Hz, 23 W
Output 16V AC, 750mA
Interface:
- Ethernet 10/100 Base-T (LAN)
- RJ-11 (WAN)
Dimensions:
- Length: 191 mm (7.5 in)
- Width: 165 mm (6.5 in)
- Height: 36 mm (1.4 in)
Inhaltsverzeichnis
Andere Broadxent Modem Handbücher
Beliebte Modem Handbücher anderer Marken
Davicom
Davicom DM562AP Bedienungsanleitung
EpiValley
EpiValley TATA indicom SXC-1080 Bedienungsanleitung
Zte
Zte WiMAX Bedienungsanleitung
Intelimax
Intelimax MA-2060 Bedienungsanleitung
SMC Networks
SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch
Telstra
Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung
US Robotics
US Robotics 3453C Bedienungsanleitung
MaxTech
MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung
Zte
Zte MF823 Bedienungsanleitung
Four-Faith
Four-Faith F1403 Bedienungsanleitung
Sierra Wireless
Sierra Wireless AIRLINK MP595W Bedienungsanleitung
Gemtek
Gemtek WiMAX WIXFBR-103 Bedienungsanleitung