Broan PM390SSP Gebrauchsanweisung

Power Module

Model number: PM390SSP

INSTALLATION,

USE & CARE INSTRUCTIONS

WWW.BROAN.COM WWW.BROAN.CA

Serial number: 99046069B

INSTALLATION, USE & CARE INSTRUCTIONS

SAFETY

!WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

• Use this unit only in the manner intended by the manufacturer. If you have questions, contact the

manufacturer at the address or telephone number listed in the warranty.

• Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

• Installation work and electrical wiring must be done by a qualified person(s) in accordance with all

applicable codes and standards, including fire-rated construction codes and standards.

• Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of

fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s guideline

and safety standards such as those published by the National Fire Protection Association (NFPA), and

the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the

local code authorities.

• When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

• Ducted fans must always be vented to the outdoors.

• Do not use this unit with any separate solid-state speed control device.

• To reduce the risk of fire, use only metal ductwork.

• This unit must be grounded.

• When installing, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves.

• When applicable local regulations comprise more restrictive installation and/or certification

requirements, the aforementioned requirements prevail on those of this document and the installer

agrees to conform to these at his own expense.

To register your product, please visit our website:

In the United States - Broan.com

In Canada - Broan.ca

For Technical Support, call:

In the United States - 800-637-1453

In Canada - 877-896-1119

Installer: Leave this manual with the homeowner.

READ AND SAVE THESE INSTRUCTIONS

Intended for domestic cooking only !!

INSTALLATION, USE & CARE INSTRUCTIONS

SAFETY

!CAUTION

!• For indoor residential use only.

• To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust air

into spaces within walls or ceilings or into attics, crawl spaces, or garages.

• Take care when using cleaning agents or detergents.

• Avoid using food products that produce flames under the Range Hood.

• For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.

• To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray,

construction dust, etc. off power unit.

• Your hood motor has a thermal overload which will automatically shut off the motor if it becomes

overheated. The motor will restart when it cools down. If the motor continues to shut off and restart,

have the hood serviced.

• The bottom of the hood MUST NOT BE LESS than 24” and recommended at a maximum of 30” above

the cooktop for best capture of cooking impurities.

• Two installers are recommended.

• Please read specification label on product for further information and requirements.

!WARNING

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

A. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers

that may ignite. Heat oils slowly on low or medium settings.

B. Always turn hood ON when cooking at high heat or when flambeing food (i.e. Crepes Suzette, Cherries

Jubilee, Peppercorn Beef Flambé).

C. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.

D. Use proper pan size. Always use cookware appropriate for the size of the surface element.

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING:*

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE

CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL

THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN - You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels - violent steam explosion will result.

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher and you already know how to operate it.

B. The fire is small and contained in the area where it started.

C. The fire department is being called.

D. You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

DIRECTIVES D’INSTALLATION, D’UTILISATION ET D’ENTRETIEN

INSTALLATION

INSTALL THE DUCTWORK

(DUCTED INSTALLATION ONLY)

NOTE: To reduce the risk of fire, use only metal ductwork.

1. Decide where the ductwork will run between the hood and

the outside. (Fig. 1)

2. A straight, short duct run will allow the hood to perform

most efficiently.

3. Long duct runs, elbows, and transitions will reduce the

performance of the hood. Use as few of them as possible.

Larger ducting may be required for best performance with

longer duct runs.

4. Install wall cap or roof cap (sold separately). Connect metal

ductwork tocap andwork backtowards thehood location.Use

2” metal foil duct tape to seal the joints between ductwork

sections.

OPTIONAL LINERS

For installations where the power module is less than 30”

above cook top, it is recommended that the power module be

mounted into a metal liner. This will allow easier cleaning and

provide protection to the cabinetry. Refer to table at righ to find

the liner model corresponding to the cabinet style and width.

Visit www.broan.com or www.broan.ca to view specific model

information.

PREPARE THE CABINET

NOTES: A. The power module has to be installed inside the

cabinet, at minimum 1” from the rear wall of the

cabinet. If installing with one of the optional liners,

use it as a template to cut the hole in the bottom

of the cabinet.

B. The internal height of cabinet has to be minimum 16”.

C. The hood should be mounted centered over the

cook top burners.

D.For cabinet without bottom, go to Alternate

mounting in INSTALL THE POWER MODULE

section on next page.

1. Cut a hole in the bottom of the cabinet, using the

dimensions shown (Fig. 2), or use the optional liner as a

template.

2. Secure 2 wood blocks having 2½” minimum height x 10¼”

long (not included) inside the cabinet, on left and right sides

of the hole, flush to the edges (Fig. 3).

3. Secure the liner (Fig. 4) using 4 mounting screws (included

with the liner).

24" MIN - 30" MAX

ABOVE COOKING SURFACE

POWER

MODULE 6" ROUND ELBOW

WALL CAP

ROOF CAP

6" ROUND DUCT

HOUSE WIRING

FIG. 1

LINER MODEL CABINET NOMINAL WIDTH

LB30 30"

LB36 36"

LB30SS 30"

LB36SS 36"

LT30 30"

LT36 36"

CUT A HOLE IN THE BOTTOM OF THE CABINET

FIG. 2

A = 10¼"

B = 19

9/16"

WOOD BLOCKS (MIN. HEIGHT: 2½")

ON LEFT AND RIGHT SIDES OF HOLE

IN BOTTOM CABINET

FIG. 3

CABINET INSIDE VIEW

METAL LINER FIG. 4

INSTALLATION, USE & CARE INSTRUCTIONS

INSTALLATION

INSTALL THE POWER MODULE

1. Remove the grease filter by pushing down on its latch tab

and tilting the filter downward (Fig. 5). Set aside the filter.

2. Remove the damper and the parts bag taped inside the

power module.

3. Disassemble the electrical cover (grey part in Fig. 6) from

inside the power module by removing both its retaining

screws. Slide the cover toward the blower in order to

disengage its hook (shown in dotted line in inset) from

the power module wall. Set aside the cover along with its

screws.

4. Run house power cable between service panel and power

module location. Stub out a 2-foot length of power cable

inside the cabinet. Attach the power cable to the power

module using an appropriate 7/8” diameter strain relief

(not included).

5. Ducted installation only: Slide the damper inside the

blower discharge opening on top of the power module

(Fig. 7).

6. Insert the power module in the cabinet (Fig. 8) and secure

to the wood blocks previously installed using (4) wood

screws included in parts bag (2 screws per side).

Alternate mounting:

7. For installation in a cabinet without bottom, insert the

power module in the liner. Install 2 wood blocks having

2½” minimum height x 10¼” long (not included), on

top of the liner and on left and right side of the power

module. Secure the power module to the wood blocks

using (4) wood screws included in parts bag (2 screws

per side) (Fig. 9).

CAUTION

Ensure the wood blocks rest completely on the

top of the liner, not on the liner flanges (Fig. 10)

NOTE: Liner apearance may vary.

8. Secure the liner (Fig. 11) using 4 mounting screws

(included with the liner).

SCREWS

FIG. 5

FIG. 6

HOOK

FIG. 7

DAMPER

CABINET INSIDE VIEW

FIG. 8

FIG. 9

LINER

LINER WITH

POWER MODULE

FIG. 11

YES NO

FIG. 10

INSTALLATION, USE & CARE INSTRUCTIONS

INSTALLATION

CONNECT DUCTWORK

Ducted Installation

Use 6” round metal duct to connect the blower discharge

to the ductwork above. Use metal foil tape to make all

joints secure and air tight.

Non-Ducted Installation

The 360NDK non-duct kit is required for this type of

installation (purchase separately). To install, follow the

intructions packed with this kit.

WIRING

WARNING

Risk of electric shock. Electrical wiring must be

done by qualified personnel in accordance with all

applicable codes and standards. Before connecting

wires, switch power off at service panel and lock

service disconnecting means to prevent power from

being switched on accidentally.

1. Using appropriate wire nuts (not included), connect house

power cable to power module wiring: BLACK to BLACK,

WHITE to WHITE and GREEN or bare wire to GREEN

ground wire (Fig. 12).

2. Reinstall wiring cover and attach it to the power module

using its retaining screws (Fig. 9). Ensure its hook (shown

in dotted line in inset) is well inserted in the power module

wall (Fig. 13).

CAUTION

Take care not to pinch wires while reinstalling wiring

cover.

INSTALL THE FILTER

Ducted Installation

Reinstall the grease filter.

Non-Ducted Installation

Attach the non-ducted filter (included with the 360NDK

non-duct kit) to the back of the grease filter using clips

(provided with non-ducted filter). To order a new non-

ducted filter, use service part number S99010464.

FIG. 12

WHITE WIRE

BLACK

WIRE

FIG. 13

HOOK

GREEN

GROUND

WIRE

HOUSE

POWER

CABLE

SCREWS

INSTALLATION AND USE & CARE INSTRUCTIONS

OPERATION, MAINTENANCE & CLEANING

OPERATION

ON/OFF Blower Push-Button: When blower is OFF,

push this button to turn ON the blower at the last selected

speed. Push this button again to turn OFF the blower.

NOTE: If there is no speed selected (all blower speed push

buttons up), the blower will not turn ON. In that case,

press on the desired speed level push button to activate

the blower.

Blower Speed Level Push Buttons: When

blower is ON, change the blower speed by pressing the

push button corresponding to the desired speed: one line

for LOW, two lines for MEDIUM and three lines for HIGH

speed.

ON/OFF Light Push Button: When lights are OFF,

push once on this button to turn ON the lights. Push this

button again to turn OFF the lights. The LED modules

in this product are the latest in LED cooktop illumination

technology - specially designed to operate in the elevated

temperatures of cooking. They offer bright lighting and last

up to 25 times as long as a standard bulb - with greater

reliability than typical replacement LED bulbs.

Non-Ducted Recirculation Filter

The Non-Ducted Recirculation filter should be

changed every 3 to 6 months. Replace more often

if your cooking style generates extra grease, such as

frying and wok cooking.

STAINLESS STEEL CLEANING

Do:

• Regularly wash with clean cloth or rag soaked

with warm water and mild soap or liquid dish

detergent.

• Always clean in the direction of original polish

lines.

• Always rinse well with clear water (2 or 3 times)

after cleaning. Wipe dry completely.

• You may also use a specialized household

stainless steel cleaner.

Don’t:

• Use any steel or stainless steel wool or any

other scrapers to remove stubborn dirt.

• Use any harsh or abrasive cleansers.

• Allow dirt to accumulate.

• Let plaster dust or any other construction

residues reach the unit. During construction/

renovation, cover the unit to make sure no dust

sticks to the stainless steel surface.

Avoid when choosing a detergent:

• Any cleaners that contain bleach will attack

stainless steel.

• Any products containing: chloride, fluoride,

iodide, bromide will deteriorate surfaces

rapidly.

• Any combustible products used for cleaning

such as acetone, alcohol, ether, benzol,

etc., are highly explosive and should never be

used close to a range.

HEAT SENTRY™

Your hood is equipped with a HEAT SENTRY™ thermostat.

This thermostat is a device that will turn on or speed up the

blower if it senses excessive heat above the cooking surface.

1) If blower is OFF - it turns blower ON to HIGH speed.

2) If blower is ON at a lower speed setting - it turns blower

up to HIGH speed.

When the temperature level drops to normal, the blower will

return to its original setting.

WARNING

The HEAT SENTRY thermostat can start the blower

even if the hood is turned OFF. When this occurs, it

is impossible to turn the blower OFF with its switch.

If you must stop the blower, do it from the main

electrical panel.

MAINTENANCE

ALWAYS SWITCH OFF THE ELECTRICITY SUPPLY

BEFORE CARRYING OUT ANY OPERATIONS ON THE

APPLIANCE.

Grease Filter

The grease filter should be cleaned frequently. Use a warm

dishwashing detergent solution. Grease filter is dishwasher safe.

Clean filter in the dishwasher using a non-phosphate

detergent. Discoloration of the filter may occur if using

phosphate detergents, or as a result of local water conditions

- but this will not affect filter performance. This discoloration

is not covered by the warranty. To minimize or prevent

discoloration, hand wash filter using a mild detergent.

INSTALLATION AND USE & CARE INSTRUCTIONS

SAFETY

INSTALLATION AND USE & CARE INSTRUCTIONS

WIRING DIAGRAM

R (Low)

O (Medium)

Motor Speeds

Motor

On/Off

Lights

On/Off

12 3

5421 6

Line

Neutral

Ground

120 VAC

Supply

BL LED driver

Heat Sentry

Thermostat

Motor

Capacitor

LED

2 1

LED

2 1

FAN MOTOR

COLOR CODE

BLACK

BLUE

BROWN

GREEN

ORANGE

RED

WHITE

YELLOW

ref: 990729775_REV-A

BK (High)

INSTALLATION, USE & CARE INSTRUCTIONS

SERVICE PARTS

KEY NO.PART NUMBER DESCRIPTION QTY.

1 SB08088378 6”ROUND DAMPER ASSEMBLY 1

2 S97018559 PARTS BAG 1

3 SB06002013 BLOWER ASSEMBLY 1

4 S99400090 STRAIN RELIEF BUSHING 1

5 S97020447 LED DRIVER WITH SCREWS 1

6 S99271659 HEAT SENTRY THERMOSTAT 1

7 S98012052 GRILLE 1

8 S97020444 LED MODULE ASSEMBLY (PAIR)1

9 S99010464 CHARCOAL FILTER WITH CLIPS (NOT ILLUSTRATED)

(FOR NON-DUCTED INSTALLATIONS ONLY, MODEL NO. 360NDK) 1

10 S99010400 GREASE FILTER 1

11 S99271674 CAPACITOR 20 μF1

12 S99030378 MECHANICAL PUSH-BUTTON CONTROL HS (5 BUTTONS) WITH SCREWS 1

13 S99770207 WIRING HARNESS 1

INSTALLATION, USE & CARE INSTRUCTIONS

WARRANTY

Limited Warranty

Warranty Period and Exclusions: Broan-NuTone LLC and Venmar Ventilation ULC (either being the “Company”) warrants to the original consumer

purchaser of its product (“you”) that the product (the “Product”) will be free from material defects in the Product or its workmanship for a period of

one (1) year from the date of original purchase (or such longer period as may be required by applicable law). For Range Hood Product that includes

built-in LED modules, the Company warrants the LED modules and driver to be free from material defects for a period of three (3) years from the date of

purchase. The limited warranty period for any replacement parts provided by the Company and for any Products repaired or replaced under this limited

warranty shall be the remainder of the original warranty period (or such longer period as may be required by applicable law).

This warranty does not cover fluorescent lamp starters, tubes, halogen, incandescent and LED bulbs, fuses, filters, ducts, roof caps, wall caps

and other accessories for ducting that may be purchased separately and installed with the Product. This warranty also does not cover (a) normal

maintenance and service, (b) normal wear and tear, (c) any Products or parts which have been subject to misuse, abuse, abnormal usage, negligence,

accident, improper or insufficient maintenance, storage or repair (other than repair by the Company), (d) damage caused by faulty installation, or

installation or use contrary to recommendations or instructions, (e) any Product that has been moved from its original point of installation, (f) damage

caused by environmental or natural elements, (g) damage in transit, (h) natural wear of finish, (i) Products in commercial or nonresidential use, or (j)

damage caused by fire, flood or other act of God or (k) Products with altered, defaced or removed serial numbers. This warranty covers only Products

sold to original consumers in the United States and Canada by the Company or its U.S. and Canadian distributors authorized by the Company.

This warranty supersedes all prior warranties and, subject to applicable law, is not transferable from the original consumer purchaser.

No Other Warranties: This Limited Warranty contains the Company’s sole obligation and your sole remedy for defective products. The foregoing

warranties are exclusive and in lieu of any other warranties and conditions, express or implied. THE COMPANY DISCLAIMS AND EXCLUDES ALL

OTHER EXPRESS WARRANTIES AND CONDITIONS, AND DISCLAIMS AND EXCLUDES ALL WARRANTIES AND CONDITIONS IMPLIED

BY LAW, INCLUDING WITHOUT LIMITATION THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent

that applicable law prohibits the exclusion of implied warranties or conditions, the duration of any applicable implied warranty or condition is limited to

the period specified for the express warranty above. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above

limitation may not apply to you. Any oral or written description of the Product is for the sole purpose of identifying it and shall not be construed as an

express warranty.

Whenever possible, each provision of this Limited Warranty shall be interpreted in such manner as to be effective and valid under applicable law, but if

any provision is held to be prohibited or invalid, such provision shall be ineffective only to the extent of such prohibition or invalidity, without invalidating

the remainder of such provision or the other remaining provisions of the Limited Warranty.

Remedy: During the applicable limited warranty period, the Company will, at its option, provide replacement parts for, or repair or replace, without

charge, any Product or part thereof, to the extent the Company finds it to be covered by and in breach of this limited warranty under normal use and

service. The Company will ship the repaired or replaced Product or replacement parts to you at no charge. You are responsible for all costs for removal,

reinstallation and shipping, insurance or other freight charges incurred in the shipment of the Product or part to the Company. If you must send the

Product or part to the Company, as instructed by the Company, you must properly pack the Product or part—the Company is not responsible for

damage in transit. The Company reserves the right to utilize reconditioned, refurbished, repaired or remanufactured Products or parts in the warranty

repair or replacement process. Such Products and parts will be comparable in function and performance to an original Product or part and warranted

for the remainder of the original warranty period (or such longer period as may be required by applicable law).

Company reserves the right, in its sole discretion, to refund the money actually paid by you for the Product in lieu of repair or replacement. If the

Product or component is no longer available, replacement may be made with a similar product of equal or greater value, at Company’s sole discretion.

This is your sole and exclusive remedy for breach of this limited warranty.

Exclusion of Damages: THE COMPANY’S OBLIGATION TO PROVIDE REPLACEMENT PARTS, OR REPAIR, REPLACE OR REFUND, AT

THE COMPANY’S OPTION, SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY AND THE COMPANY’S

SOLE AND EXCLUSIVE OBLIGATION. THE COMPANY SHALL NOT BE LIABLE FOR INCIDENTAL, INDIRECT, CONSEQUENTIAL OR

SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE PRODUCT, ITS USE OR PERFORMANCE. Incidental damages

include but are not limited to such damages as loss of time and loss of use. Consequential damages include but are not limited to the cost of repairing

or replacing other property which was damaged if the Product does not work properly.

THE COMPANY SHALL NOT BE LIABLE TO YOU, OR TO ANYONE CLAIMING UNDER YOU, FOR ANY OTHER OBLIGATIONS OR

LIABILITIES, INCLUDING, BUT NOT LIMITED TO, OBLIGATIONS OR LIABILITIES ARISING OUT OF BREACH OF CONTRACT OR

WARRANTY, NEGLIGENCE OR OTHER TORT OR ANY THEORY OF STRICT LIABILITY, WITH RESPECT TO THE PRODUCT OR THE

COMPANY’S ACTS OR OMISSIONS OR OTHERWISE.

Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply

to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from jurisdiction to jurisdiction. The disclaimers,

exclusions, and limitations of liability under this warranty will not apply to the extent prohibited by applicable law.

This warranty covers only replacement or repair of defective Products or parts thereof at the Company’s main facility and does not include the cost of

field service travel and living expenses.

Any assistance the Company provides to or procures for you outside the terms, limitations or exclusions of this limited warranty

will not constitute a waiver of such terms, limitations or exclusions, nor will such assistance extend or revive the warranty.

The Company will not reimburse you for any expenses incurred by you in repairing or replacing any defective Product, except for those incurred with

the Company’s prior written permission.

How to Obtain Warranty Service: To qualify for warranty service, you must (a) notify the Company at the address or telephone number stated below

within seven (7) days of discovering the covered defect, (b) give the model number and part identification and (c) describe the nature of any defect in

the Product or part. At the time of requesting warranty service, you must present evidence of the original purchase date. If you cannot provide a copy

of the original written limited warranty, then the terms of the Company’s most current written limited warranty for your particular product will control.