Brocade Communications Systems 200E Series Bedienungs- und Wartungshandbuch

53-1001274-02

28 July 2009

Fixed Rack Mount Kit

Installation Procedure

Supporting Brocade 200E, 300, 4100, 4900, 5000, 5100, 5300, 7500 series,

7600, 7800, 8000, AP7420 and Encryption Switch

53-1001274-02

*53-1001274-02*

2 of 12 Fixed Rack Mount Kit Installation Procedure

53-1001274-02

Brocade, the B-wing symbol, BigIron, DCX, Fabric OS, FastIron, IronPoint, IronShield, IronView, IronWare, JetCore, NetIron, SecureIron, ServerIron,

StorageX, and TurboIron are registered trademarks, and DCFM, Extraordinary Networks, and SAN Health are trademarks of Brocade

Communications Systems, Inc., in the United States and/or in other countries. All other brands, products, or service names are or may be

trademarks or service marks of, and are used to identify, products or services of their respective owners.

Notice: This document is for informational purposes only and does not set forth any warranty, expressed or implied, concerning any equipment,

equipment feature, or service offered or to be offered by Brocade. Brocade reserves the right to make changes to this document at any time,

without notice, and assumes no responsibility for its use. This informational document describes features that may not be currently available.

Contact a Brocade sales office for information on feature and product availability. Export of technical data contained in this document may

require an export license from the United States government.

The authors and Brocade Communications Systems, Inc. shall have no liability or responsibility to any person or entity with respect to any loss,

cost, liability, or damages arising from the information contained in this book or the computer programs that accompany it.

The product described by this document may contain “open source” software covered by the GNU General Public License or other open source

license agreements. To find out which open source software is included in Brocade products, view the licensing terms applicable to the open

source software, and obtain a copy of the programming source code, please visit

http://www.brocade.com/support/oscd.

Brocade Communications Systems, Incorporated

Document History

The following table lists all published versions of the Fixed Rack Mount Kit Installation Procedure.

Corporate and Latin American Headquarters

Brocade Communications Systems, Inc.

1745 Technology Drive

San Jose, CA 95110

Tel: 1-408-333-8000

Fax: 1-408-333-8101

E-mail: inf[email protected]om

Asia-Pacific Headquarters

Brocade Communications Systems China HK, Ltd.

No. 1 Guanghua Road

Chao Yang District

Units 2718 and 2818

Beijing 100020, China

Tel: +8610 6588 8888

Fax: +8610 6588 9999

E-mail: [email protected]

European Headquarters

Brocade Communications Switzerland Sàrl

Centre Swissair

Tour B - 4ème étage

29, Route de l'Aéroport

Case Postale 105

CH-1215 Genève 15

Switzerland

Tel: +41 22 799 5640

Fax: +41 22 799 5641

E-mail: emea-inf[email protected]

Asia-Pacific Headquarters

Brocade Communications Systems Co., Ltd. (Shenzhen WFOE)

Citic Plaza

No. 233 Tian He Road North

Unit 1308 – 13th Floor

Guangzhou, China

Tel: +8620 3891 2000

Fax: +8620 3891 2111

E-mail: [email protected]

Title Publication number Summary of changes Date

Fixed Rack Mount Kit Installation

Procedure

53-0000244-03 Added 3250 and 3850

support and new

illustrations and format.

December 2003

Fixed Rack Mount Kit Installation

Procedure

53-0000244-04 Updated to include 3800

and 4100; minor editorial

changes.

July 2004

Fixed Rack Mount Kit Installation

Procedure

53-0000244-05 Updated to include 200E;

minor editorial changes.

January 2005

Fixed Rack Mount Kit Installation Procedure 3 of 12

53-1001274-02

Fixed Rack Mount Kit Installation

Procedure

53-0000244-06 Minor technical corrections. June 2005

Fixed Rack Mount Kit Installation

Procedure

53-1000244-07 Updated with minor

hardware changes; minor

editorial changes.

October 2005

Fixed Rack Mount Kit Installation

Procedure

53-1000244-08 Added support for 4900 and

7500.

February 2006

Fixed Rack Mount Kit Installation

Procedure

53-0000244-09 Added support for the 5000

switch.

December 2006

Fixed Rack Mount Kit Installation

Procedure

53-0000244-10 Rebranded to current

standards and changed title

and text of manual to

include “7500 series.”

January 2008

Fixed Rack Mount Kit Installation

Procedure

53-0000244-11 Added support for the

Brocade 300, 5100, and

5300 switches

March 2008

Fixed Rack Mount Kit Installation

Procedure

53-0000244-12 Added support for the

Brocade Encryption Switch

August 2008

Fixed Rack Mount Kit Installation

Procedure

53-1001274-01 Added support for the

Brocade 8000 Switch

March 2009

Fixed Rack Mount Kit Installation

Procedure

53-1001274-02 Added support for the

Brocade 7800 Switch

July 2009

Title Publication number Summary of changes Date

4 of 12 Fixed Rack Mount Kit Installation Procedure

53-1001274-02

Contents

This document provides instructions to install a 1U, 1.5U, or 2U switch (or SAN Router) in a 19-in. (48.3 cm) EIA

cabinet using the Fixed Rack Mount Kit. The document is organized as follows.

•Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

•Installation requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

•Tool requirements and parts list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

•Installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Introduction

The supported switches are listed in Table 1. The switch can be installed so that the port side is either flush with the

front rails or recessed from the front rails. A recessed position allows a more gradual bend in the fiber optic cables

connected to the switch.

TABLE 1 Supported switches

Switch Height Switch Model

1U Brocade 200E

Brocade 300

Brocade 4100

Brocade 5000

Brocade 5100

Brocade 7500 series

Brocade 7600

Brocade 7800

Brocade 8000

2U Brocade 4900

Brocade 5300

Brocade AP7420

Brocade Encryption Switch

Fixed Rack Mount Kit Installation Procedure 5 of 12

53-1001274-02

Installation requirements

Allow 15 to 30 minutes to complete this procedure. Note the following requirements to ensure correct installation

and operation:

•Provide space in a 19-in. (48.3 cm) EIA cabinet, as required for the switch type, with a minimum distance of

28.25 in. (71.76 cm) and a maximum distance of 29.88 in. (75.90 cm) between the front and back rails.

•Verify that the additional weight of the switch does not exceed the cabinet’s weight limits.

•Ensure that an electrical branch circuit with the following characteristics is available:

-Required voltage and frequency as indicated in the hardware reference manual. (200-230 VAC is always

preferred)

-Protection by a circuit breaker in accordance with local electrical codes.

-Supply circuit, line fusing, and wire size that conform to the electrical rating on the switch nameplate.

-Grounded outlet compatible with the power cord and installed by a licensed electrician.

•Ensure that all equipment installed in the cabinet is grounded through a reliable branch circuit connection. Do

not rely on a secondary connection to a branch circuit, such as a power strip.

•Ensure that the cabinet is mechanically secured to ensure stability.

•Ensure that the air temperature at the fan inlet is less than 104oFahrenheit (40oCelsius) during switch

operation.

•Ensure that the airflow available at the air vents meets the minimum requirements for the switch.

ATTENTION

Install the switch with the fan side facing the air-intake aisle. The chassis air intake is on the fan side and exhaust is

on the port side.

Tool requirements and parts list

The following items are required to install a switch using the fixed rack mount kit:

•Clamps or other means of temporarily supporting the switch in the cabinet.

•Phillips #2 screwdriver with torque capability.

•1/4 in. slotted-blade screwdriver with torque capability.

ATTENTION

Use the screws specified for use with the switch. Longer screws can damage the switch.

Ensure that the items listed in Table 2 and illustrated in Figure 1 are included in the kit.

TABLE 2 Parts list

Item Description Quantity

1 Bracket, front right 1

2Bracket,frontleft 1

3 Bracket, rear right 1

4 Bracket, rear left 1

6 of 12 Fixed Rack Mount Kit Installation Procedure

53-1001274-02

FIGURE 1 Items in Fixed Rack Mount Kit

5 Screw, 8-32 x 5/16 in., panhead Phillips (torque to 15 in.-lbs, 17 cm-kgs) 12

6 Screw, 6-32 x 1/4 in., flathead Phillips (torque to 9 in.-lbs, 10 cm-kgs) 8

7 Screw, 10-32 x 5/8 in., panhead Phillips (torque to 25 in.-lbs, 29 cm-kgs) 8

8Retainernut,10-32 8

1 Bracket, front right 5 Screw, 8-32 x 5/16 in., panhead Phillips

2 Bracket, front left 6 Screw, 6-32 x 1/4 in., flathead Phillips

3 Bracket, rear left 7 Screw, 10-32 x 5/8 in., panhead Phillips

4 Bracket, rear right 8 Retainer nut, 10-32

TABLE 2 Parts list

Item Description Quantity

scale: 3/16" = 1"

LEFT

RIGHT

#2-0002402-02REV.B

FOXCONN 01/03/2005

5678

(8x)(8x)(12x) (8x)

(10-32)(10-32 x 5/8 in.)(6-32 x 1/4 in.)(8-32 x 5/16 in.)

Fixed Rack Mount Kit Installation Procedure 7 of 12

53-1001274-02

Installation procedure

ATTENTION

The switch must be turned off and disconnected from the fabric during this procedure.

NOTE

Although this document describes how to install a 1U, 1.5U, and 2U switch, the illustrations show a 1U switch as a

typical configuration.

Complete these tasks to install the switch in a cabinet:

•“Attaching front brackets”

•“Installing the switch in the cabinet”

•“Attaching rear brackets to front brackets”

•“Attaching rear brackets to cabinet rails”

Attaching front brackets

Complete the following steps to attach the front brackets to the switch.

1. Position the right front bracket (Item 1) with the flat side against the right side of the switch (Figure 2).

2. Insert two 8-32 x 5/16 in. screws (Item 5) into one of the pairs of vertically aligned holes in the bracket and then

into the pair of holes on the side of the switch. To install the switch in a recessed position in the cabinet, use the

bracket holes that are set back from the end of the bracket.

3. Insert each 8-32 x 5/16 in. screw (Item 5) through the holes in the bracket and into the corresponding hole in

the switch.

4. Tighten all 8-32 x 5/16 in. screws to a torque of 15 in.-lbs (17 cm-kgs).

5. Repeat step 1 through step 5 to attach the left front bracket (Item 2) to the left side of the switch.

8 of 12 Fixed Rack Mount Kit Installation Procedure

53-1001274-02

FIGURE 2 Position the front bracket

Installing the switch in the cabinet

Complete the following steps to install the switch in the cabinet.

1. Position the switch in the cabinet (Figure 3), providing temporary support under the switch until the rail kit is

secured to the cabinet.

2. Attach the right front bracket (Item 1) to the right front rack rail using two 10-32 x 5/8 in. screws (Item 7) and

two retainer nuts (Item 8).

3. Repeat step 2 to attach the left front bracket (Item 2) to the left front rack rail.

4. Tighten all 10-32 x 5/8 in. screws (Item 7) to a torque of 25 in.-lbs (29 cm-kgs

1 Bracket, front right

5 Screw, 8-32 x 5/16 in., panhead Phillips

scale: 1/8" = 1"

IOIOI

SilkWorm4100

LNK

SPD

RIGHT

#2-0002402-02R

EV. B

FOXCONN01/03/2005

Fixed Rack Mount Kit Installation Procedure 9 of 12

53-1001274-02

NOTE

The figure above is shown with a recessed mounting configuration on the left and a flush mounting

configuration on the right. You can select either mounting option.

FIGURE 3 Position the switch in the cabinet

Attaching rear brackets to front brackets

Complete the following steps to attach the rear brackets to the front brackets.

1. Position the right rear bracket (Item 4) inside the right front bracket (Item 1) (Figure 4).

2. Attach the brackets using four 6-32 x 1/4 in. screws (Item 6).

3. Adjust the brackets to cabinet depth and tighten the Item 6 screws to a torque of 9 in.-lbs (10 cm-kgs).

1 Bracket, front right 7 Screw, 10-32 x 5/8 in., panhead Phillips

2Bracket,frontleft 8Retainernut,10-32

scale: 1/8" = 1"

LEFT

IOIOI

SilkWorm4100

LNK

SPD

RIGHT

#2-0002402-02REV.B

FOXCONN01/03/2005

10 of 12 Fixed Rack Mount Kit Installation Procedure

53-1001274-02

4. Repeat step 1 through step 3 to attach the left rear bracket (Item 3) to the left front bracket (Item 2).

FIGURE 4 Position the rear and front brackets

Attaching rear brackets to cabinet rails

Complete the following steps to attach the rear brackets to the cabinet rails.

1. Attach the right rear bracket (Item 4) to the right rear cabinet rail using two 10-32 x 5/8 in. screws (Item 7) and

two retainer nuts (Item 8) (Figure 5).

2. Repeat step 1 to attach the left rear bracket (Item 3) to the left rear cabinet rail.

3. Tighten the 10-32 x 5/8 in. screws (Item 7) to a torque of 25 in.-lbs (29 cm-kgs).

ATTENTION

Connect the power cords to a grounded outlet only. Ensure that any power cord is routed so that it is not exposed to

stress. Leave a minimum service loop of 6 in. in the power cord(s) at the connection to switch. This allows enough

freedom of movement to plug and unplug the power cord(s).

4. Provide power to the switch by connecting the power cord(s) to the power connectors on the switch and a power

outlet. Some switches require you to flip a power switch to be powered on.

NOTE

Do not connect the switch to the network until the IP address is correctly set. Refer to the appropriate hardware

reference manual for information on setting the IP address for the switch.

1 Bracket, front right 6 Screw, 6-32 x 1/4 in., flathead Phillips

4 Bracket, rear right

RIGHT

#2-0002402-02 REV.B

FOXCONN 01 /03/2005

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Brocade Communications Systems Schalten Handbücher