Bronica SQ-B Bedienungsanleitung
Operating Guide for the
BRONICA SQ-B
6 cm x 6 cm Format, Manual SLR Camera with 80mm lens and 120 Film Back
PROFICIENCY REQUIRED
LOADING THE FILM
To open the back—squeeze the film holder release buttons (#'s 13 and 14), located on top right behind the viewfinder
(#8), toward each other; the back will spring open and the film holder might fall out, be prepared! Remove the film
holder. Gently push the top left side spool holder shaft (#27) out (a little trap door will
fall open). Insert right end of film onto the right side shaft. Close the little trap door (the
left side shaft) and the film spool should be engaged. Draw the
leading end across the top roller (see diagram) and in front of
the pressure plate, emulsion side out. Pull across the bottom
roller and insert the leading end into the take up spool. Wind
slightly with film back winding knob (#20) until securely
engaged. Place film holder on back of camera, making sure it
sits snugly. Wind film winding crank (#18) until starting
point or arrow mark is lined up with red triangle on the left
side of top spool holder. Close back until it latches securely.
Don't Force It! If it will not easily close the film holder is
not snug against the camera. Re-adjust it and try again. Wind
film crank and release shutter until you see the “1” in the
exposure counter (#15).
FILM ADVANCE AND SHUTTER COCKING
Rotate the film winding crank (#18) forward (clockwise) one time; the film will advance
one frame and the shutter will be cocked. You will feel resistance as the crank begins the
wind; don’t panic, that’s the shutter being cocked.
SETTING THE APERTURE AND SHUTTER SPEED
Use the aperture ring (#4) to set the F-stop. The shutter speed dial (#10) is located on the left side. You can view the
speed setting by checking the shutter speed scale (#11).
DISTANCE AND DEPTH OF FIELD SCALE
Rotate the focus ring (#3) and line up the distance (the two rows of numbers circling the ring next to the focus ring) with
the orange index line that reads 2.8. The depth of field scale (#5) is made up
of identical pairs of numbers on either side of the index number. These pairs
indicate the distance that will be in focus at these lens openings. The depth of
field preview button (#23) is located on the left side of the lens. Media Loan
does not have any other lenses or film backs for the Bronica so there is no
need to use the lens release button (#24) or the
film back release button (#31).
VIEWING & FOCUSING
Open the focusing hood by
pushing up on the catch (#9)
at the rear of the folded finder.
The magnifier (#12) is flipped into position by sliding the release (located
inside the focusing hood on the right front) to the left, indicated by arrow.
The lens is focused by rotating the focus ring (#3) in either direction, while
checking the image in the split-image spot in the center of the focusing
screen. A cable release can go into #28, the cable release socket.
READ ALL INSTRUCTIONS AND BECOME FAMILIAR WITH THE BRONICA BEFORE USE
Recycled & Recyclable BronicaOpGuide/8/01wdc
Media Loan The Library Group (360)867-6253
The Evergreen State College Olympia, WA 98505
http://www.evergreen.edu/media
BRONICA SQ-B
Right Side
Left Side
Front
The Bronica is a very expensive and delicate piece of professional equipment. Treat it with great care—remember, you
the borrower assume full responsibility for loss or damage. The Bronica SQ-B does not have a built-in exposure meter so
you will need to check out a light meter from Media Loan.
SHUTTER RELEASE
The release (#1) is located below the lens on the right. If the red dot is lined up with the red L,
the shutter is locked; rotate counter clockwise to unlock. The red LED light will light up when
you depress the release and the camera is loaded to indicate an exposure has been made.
The LED will not light if:
• The shutter release is locked
• Film is not advanced or between “S” and “1”
• Shutter is not cocked
• Lens release button is depressed
• All frames have been exposed (i.e., 12 for 120)
The shutter blades will close, under-exposing the film if the winding crank is accidentally rotated
before the exposure is completed, as in the case of a slow shutter speed setting.
FLASH PHOTOGRAPHY
Plug a flash cord into the flash plug (#2). Do not twist; straight in - straight out. The lens will automatically synchronize all
shutter speed settings up to 1/500 of a second.
FILM UNLOADING
After completely exposing one roll of film (12 exposures), continue winding until the leader paper
is completely wound up, or approximately eight full turns of the advance crank. Then, open the
back cover and take out the film holder. Remove the take-up spool from the film holder while
holding the exposed film so that it will not unwind. Seal the exposed film.
BATTERY CHECK
A red LED is located inside the viewfinder. It lights up when the
battery check button (#25), located on the left side behind the film
speed dial, is pressed and when an exposure is made. Indicates battery
is OK.
MULTIPLE EXPOSURE
To make multiple exposures, rotate the film winding crank (#18) to
advance the film and cock the shutter. Rotate the multiple exposure
lever (#17) clockwise, from 12 o’clock to 3 o’clock. It will lock in that position and the shutter can
be cocked any number of times without the film advancing. Don’t forget to return the lever to its 12
o’clock position when your multiple exposure is finished.
MIRROR LOCK-UP
The mirror lock-up switch (#21) is located in front of the winding crank. It has 3 settings; N
(normal—for shooting without locking up the mirror), S (single frame) or C (continuous—for
shooting with the mirror locked up). Rotate the lock-up lever in a counter clockwise direction and line up N, S, or C with the
dot. The lens shutter will close completely and the mirror will swing up.
INFRARED PHOTOGRAPHY
The red line next to the orange distance index line on the lens barrel is the infrared index. After focusing in the normal manner,
reset the distance to the red index line by shifting the distance ring. This will retain focus of the longer infrared rays.
IMPORTANT PRECAUTIONS WITH THIS CAMERA:
•PROTECT FROM EXTREME TEMPERATURE CHANGES
• PROTECT FROM IMPACT AND VIBRATIONS
• PROTECT FROM DIRT, SAND, WATER, VOLCANIC ASH ETC.
• ALWAYS PROTECT THE LENS WITH ITS LENS COVER
• DO NOT OVER TIGHTEN ANYTHING
• DO NOT USE SILICONE-COATED CLOTH ON THE LENS OR VIEWING SCREEN
• HAVE MEDIA LOAN CLEAN CAMERA IF LENS IS DIRTY
PLEASE RETURN THE CAMERA TO MEDIA LOAN IF YOU EXPERIENCE ANY PROBLEMS.
DO NOT ATTEMPT TO FIX IT YOURSELF!
Andere Handbücher für SQ-B
1
Inhaltsverzeichnis
Andere Bronica Digitalkamera Handbücher
