BROOD DRNX BRW Bedienungsanleitung

DRNX BRW BY BROOD

MANUAL

DRNX BY BROOD

CONTENTS

SAFETY REGULATIONS 3

GENERAL INFORMATION 4

COMPONENTS 5

INSTALLATION 6

OPERATION 7

ADJUSTABLE SETTINGS 8

CARE 9

TROUBLESHOOTING 10

FAQ 11

WARRANTY 12

DECOMMISSIONING 13

CONTACT 14

DRNX BY BROOD

SAFETY REGULATIONS

NEVER ALLOW WATER TO COME INTO CONTACT WITH ANY OF THE ELECTRICAL PARTS OF

DRNX BRW: THERE IS A DANGER OF CREATING A SHORT CIRCUIT.

INTENDED USE

DRNX BRW is intended to be used in cafes, restaurants, and pantries. It dispenses liquid from its internal

reservoir, infusing it with atmospheric nitrogen and chilling it to 2°C. Do not pour liquids that are above room

temperature or that are unﬁltered. It must only be operated by a trained person. The appliance is not to be used

by persons (including children) with reduced physical, mental or sensory abilities or with scarce experience and/or

expertise, unless they are supervised by a person responsible for their safety, or they are instructed by this person

on how to properly use DRNX BRW.

POWER SUPPLY

DRNX BRW must be connected to the power supply in accordance with its speciﬁcations. Only connect it with

the speciﬁed supply voltage.

POWER CORD

Never use DRNX BRW if the power cord is defective. Report any defects in the cord and/or plug to the service

provider immediately. Do not pass the power cord around corners, over sharp edges or over hot objects and keep

it away from oil. Do not use the power cord to carry or pull the machine. Do not pull out the plug by the power

cord nor touch it with wet hands. Do not let the power cord hang freely from tables or shelves.

FOR THE SAFETY OF OTHERS

Ensure that children cannot play with DRNX BRW and/or the packaging materials. Observe the warning and

safety instructions on the electrical components and in this manual. Improper use of DRNX BRW such as

opening it during operation, incorrectly operating it, or not following standard guidelines for operating electrical

equipment may lead to injury.

FIRE SAFETY PRECAUTIONS

In case of ﬁre, use carbon dioxide (CO2) extinguishers. Do not use water or dry powder extinguishers.

SUITABLE LOCATION FOR OPERATION AND MAINTENANCE

DRNX BRW should be installed in accordance with the safety regulations in force at the time of installation.

Operate it in an environment between 13°C and 32°C. Make sure it is a dust-free environment. Avoid placing

open ﬂames and/or incandescent objects near it to avoid melting or other damage to the dispenser housing. If the

dispenser has been exposed to such conditions, alert the service provider who will carry out a safety check.

STORING DRNX

If DRNX BRW is to remain inactive for a long time, turn it o and unplug it. Store it in a dry place, out of reach

of children. Make sure the storage area is between 13°C and 40°C. Keep it protected from dust and dirt.

DRNX BY BROOD

SAFETY REGULATIONS

GENERAL INFORMATION

REPAIRS / MAINTENANCE

In case of failure, problems or a suspected fault resulting from a fall, immediately remove the plug from the

power socket and alert the service provider or specialized technician. Never attempt to operate it if it is faulty.

Please report any fault to your service provider. Only the service provider and/or technician may carry out

servicing operations and repairs on DRNX BRW, unless otherwise informed. Any repair of the dispenser must

be done only when it is switched o and it is ascertained that there is no electric current. All spare parts must be

obtained from your service provider. Follow the service and maintenance instructions in this operation manual.

USE

DRNX BRW pulls any ﬁltered liquid from an internal reservoir. The liquid can be poured directly into the

reservoir, or it can be housed in a soft-walled Bag-in-Box (BiB) bladder. The reservoir is refrigerated such that

the liquid is dispensed at 2°C. It can be infused with atmospheric nitrogen, or it can be poured still.

VISCOSITY OF LIQUID

Ensure that your beverage has been ﬁltered. Thick liquids risk slowing down the liquid pump inside. DRNX BRW

comes with a pre-ﬁlter that is already ﬁtted into the machine.

DRNX BY BROOD

COMPONENTS

1 — Tap Handle

2 — Tap Body

3 — Nozzle

4 — Exterior

5 — Inlet Connector

6 — Main ON/OFF Switch

7 — Legs

8 — Forward Plate

9 — Rear Plate

10 — Side Panel(s)

11 — Infuser Dial

12 — Power Plug

13 — Vents/Exhaust

14 — Pre-Filter

15 — Thermostat

16 — Calibration Knob

17 — Pump ON/OFF Switch

18 — Ventilation Valve

19 — Internal Reservoir

20 — Internal Reservoir Collar

21 — Magnetic Stir Bar

22 — BiB bladder Adapter

23 — BiB bladder Adapter Inlet

SPECIFICATIONS

Width: 10.25in Power Supply: 100-120V/60Hz; 200-240V/50Hz

Height: 14.75in Nominal Power: 334W

Depth: 20.00in

Weight: 73lbs

Dispensing Capacity: 1.5L/min (0.4gpm)

Coee Temp at Tap: 2°C (36°F)

DRNX BY BROOD

INSTALLATION

1. Install on a clean and dry surface.

Allow no less than 20 centimetres of space from the back.

2. Assemble the tap handle.

Tilt the machine slightly if you need to.

3. For use with a BiB bladder, screw the BiB bladder adapter into the BiB

bladder inlet.

Place your BiB bladder adapter towards the bottom of the reservoir. This will

allow the contents of the BiB bladder to ﬂow through the machine with ease.

Never use a BiB bladder that has a sti wall.

SETUP

THE CENTER IS THREADED.

THE BiB BLADDER ADAPTER IS FASTENED INSIDE

THIS THREADED HOLE.

MAGNETIC STIRRER

DRNX BY BROOD

1. Switch on the main ON/OFF button at the bottom of the machine.

There will be a red light when the switch is on.

2. Switch on the pump ON/OFF button located at the top of the machine.

There will be a red light when the switch is on.

Pour the beverage into the reservoir and pull the tap forward to

prime the pump.

The pump will automatically turn o if it runs dry for one minute.

This will notify the operator that the beverage container is empty.

Simply switch the pump o, then on again to reset.

3. Place the magnetic stir bar at the bottom of the internal reservoir.

4. Pour your beverage into the internal reservoir.

Make sure not to pour above the internal reservoir collar.

Make sure not to dislodge the magnetic stirrer when pouring.

5. Place your cup beneath the stout at an angle. To pour a STILL beverage,

turn the infuser dial counter-clockwise. To pour a NITRO beverage, turn

the infuser dial clockwise.

Please note, if the last pour was nitro cold brew and the operator wants

the next pour to be still cold brew, there will be less than 10 mL (0.34

oz) of nitro cold brew in the tap that will come out. Every subsequent

still cold brew pour will come out fully still, until the next nitro cold

brew pour.

6. Return the tap to the start position when you have completed the pour.

Ensure that the coee is ﬁltered with a ﬁneness of at least 100 μm (microns).

OPERATION

STEPS

MAIN ON/OFF SWITCH

ON BOTTOM OF MACHINE

PUMP ON/OFF SWITCH

ON TOP OF MACHINE

!WARNING: Never run hot liquid above 30°C (86°F) through DRNX BRW.

DRNX BY BROOD

ADJUSTABLE SETTINGS

Locate the infuser dial at the front of the machine. Turn the dial counter-clockwise towards the 9 o’clock

position to pour a still drink. Turn the dial clockwise towards the 12 o’clock position to pour a nitrogenated

drink.

If the level of nitrogen infusion is too high at the maximum (12 o’clock) position, then follow the steps below to

decrease the level of nitrogen infusion. This is a one-time calibration process to adjust the amount of infusion

at the maximum position only.

1. Locate and remove the ten screws on the left panel.

2. Locate the calibration knob at the forefront section. Turning it clockwise will decrease the amount

of nitro.

3. Return the side panel and screw it securely.

MODIFCATION OF DESIRED TEMPERATURE VALUE

Press button for at least half second, to display the setpoint value.

By keeping button pressed, use button or to set the desired value.

When button is released, the new value is stored.

If the operator sets the temperature at freezing, it runs the risk of freezing the Cold Brew. If this happens, turn

o the fridge as described in step 2. Keep o for 2 hours.

Info / Setpoint button.

Manual defrost / Decrease button.

Increase / Manual Activation button.

Exit / Stand-by button.

TEMPERATURE CONTROL

NITROGEN CALIBRATION

DRNX BY BROOD

CARE

Follow the cleaning procedures below as it is essential to both extend the life of the DRNX BRW, and to

achieve the desired ﬂavor of cold brew. It must be cleaned twice week as described in the steps below.

Never use hot water during the cleaning procedure.

BROOD recommends the following cleaning detergent: 1-2-COLD BREW Cleaner by Urnex

1. Empty the reservoir by pouring out all liquid through the tap.

If using a BiB bladder, then unscrew the BiB bladder adapter and remove

both the adapter and the bladder from the reservoir.

2. Remove the magnetic stir bar and put in a bath of cleaning detergent.

3. Fill the reservoir with room temperature water.

4. Prepare the cleaning solution.

Dissolve any espresso cleaning detergent in the water to create a

cleaning solution.

5. Unscrew the nozzle from the tap by turning it counter-clockwise. Wash

the nozzle with clean water.

After washing, please reassemble it onto the tap.

6. Connect a 1/4 inch tube to the ventilation port.

Drop the other end of the tube into the cleaning solution inside

the reservoir.

7. After 30 minutes have passed pull the tap downward to run the solution

through DRNX BRW.

Keep pouring until all the solution has been ﬂushed through the dispenser.

8. Wipe down the inside of reservoir with a clean paper towel.

9. Disconnect the 1/4 inch tube from the ventilation port.

10. Return the magnetic stir bar to the bottom of the reservoir.

CLEAN & MAINTAIN

BIWEEKLY CLEANSE

DRNX BY BROOD

TROUBLESHOOTING

QUICK SOLUTIONS

There is too much nitro The calibration knob is not

set correctly.

Follow steps in to decrease the level of infusion

outlined in section “Nitrogen Calibration”

There is no nitro even though it's set to

maximum.

There is a block in the spout Unscrew the spout and check to see if there is

any sediment. Remove the components inside

the spout and wash thoroughly.

Too many large bubbles BiB bladder is not facing

downward.

Place the outlet of the bladder at the bottom of

the reservoir. The pump will only pull liquid. It

will prevent it from sucking in air that is in the

bladder

Product is not cold enough. The temperature setting is

too high.

Check to see if the main switch underneath the

machine is on. Follow the instructions in the

manual to change the temperature setting.

The cold brew in the

container hasn’t chilled yet.

After pouring room temperature liquid inside

the reservoir, it will take approximately 25

minutes to reach 2°C.

DRNX BRW is not pouring cold brew. The pre-ﬁlter is clogged. Unscrew the left panel, and located the pre-

ﬁlter. Unscrew the cap and remove the internal

mesh. Clean and return the mesh. Screw the cap

back on.

There is no electrical power

connected to the machine

Check to see if the main switch underneath

DRNX BRW is on. Then check to see if the

pump switch on the top of the machine is on. If

either one is o, please switch them on. If the

pump switch is ﬂashing, switch it o then on to

reset the pump.

The pump ON/OFF switch

needs to be reset.

When your container is empty, the pump turns

o and the ON/OFF switch ﬂashes red. Switch

it o then on to reset the pump.

Inhaltsverzeichnis

Andere BROOD Kaffeemaschine Handbücher

BROOD

BROOD Nitro V2PX Bedienungsanleitung

Beliebte Kaffeemaschine Handbücher anderer Marken

Taurus

Taurus Livorno 6 Bedienungsanleitung

Delta-q

Delta-q QUICK Bedienungsanleitung

Bunn

Bunn LCA-1 Fehlerbehebungshandbuch

Black & Decker

Black & Decker BLACK DECKER HOME DE790 Montageanleitung

Saeco

Saeco Vienna Plus Sup 018M Bedienungsanleitung

DeLonghi

DeLonghi DC300 Bedienungsanleitung

INCAPTO

INCAPTO BXCO1470E Bedienungsanleitung

Bosch

Bosch TASSIMO finesse TAS16B Series Bedienungsanleitung

Exido

Exido 245-072 Bedienungsanleitung

Animo

Animo OptiVend Choco Bedienungsanleitung

Siemens

Siemens TQ505DF Series Bedienungsanleitung

DeLonghi

DeLonghi ECI341 Bedienungsanleitung

Krups

Krups KT406511 Bedienungsanleitung

Cimbali

Cimbali M32 Classic Bedienungsanleitung

Philips

Philips HL3844N Bedienungsanleitung

Bosch

Bosch TES 515 SERIES Bedienungsanleitung

Tekmatix

Tekmatix TMFM - 65 Bedienungsanleitung

Scarlett

Scarlett SC-CM33005 Bedienungsanleitung