Brother MFC-9160 Bedienungsanleitung
Version A
Press and slide
Load the paper
with the lever down
THANK YOU!
… FOR PURCHASINGYOUR BROTHER MACHINE.
WE ARE SUREYOU WILL BE IMPRESSEDWITHTHE
CONVENIENT WAYTHATYOUR NEW MACHINE PERFORMS SO
MANYTASKS WITH GREAT RESULTS!
Follow these simple instructions in numerical order.
For greater detail, consult your Owner’s Manual and CD-ROM.
Alternatively, if you cannot solve a problem:
Refer to Frequently Asked Questions (FAQ’s) on Brother Solutions
Web Site: URL: http://solutions.brother.com
Call Brother Customer Service at: 0161 931 2354
Packing List
Keep the packing materials for possible future transport. If you do not pack the machine properly, it may
void your warranty.
Drum Unit Assembly
Owner’s Manual
Brother Quick
Setup Guide
Paper Support
IEEE-1284 Compliant
Bi-directioned Cable
Mains Power Cord
CD-ROM
For USB Cable
Cable Tie
Starter Sheet
Do NOT remove
the Starter Sheet!
Mains Power Cord
(Example for
the U.K.)
A. Attach the paper support to
the multi-purpose sheet
feeder.
B. Pull out the paper tray and
the extension.
C. If your paper size is A4 or
Letter, extend the paper
stopper by pulling it toward
you.
(For A4 and Letter paper)
– 1 –
MFC-9160 Quick Setup Guide
23
1
4
Attach the Plastic Support
and Pull out the Paper Tray
Install the Drum Unit
Load Paper 5Install Mains Power Cord
A. Adjust the guides to the position for the paper
size you are using.
B. Fan the paper well.
A. Unpack the drum unit assembly, and gently
rock it from side to side five or six times to
distribute the toner evenly inside the
cartridge.
B. Open the top cover of the machine by pulling
the lever toward you and lifting the cover.
To prevent damage to the drum, do not
expose it to light for longer than a few
minutes.
Do NOT remove the clear plastic starter
sheet this will be ejected while the machine
is warming up.
C. Holding the drum unit by its handles, insert it
into the machine.
C. Push down the paper lever. Load the paper
(with the lever down). Make sure the print
side is toward the fax machine and the paper
level is stacked below the paper mark.The
feeder can hold up to 200 sheets of paper, or
up to 10 envelopes.
Turn the power switch ON.
Complete reading this guide before connecting the Parallel or USB
cables.
D. Close the top cover.
For Windows®95/98/98SE/Me/2000 Users
Setting Up the MFC and PC to Work Together
BeforeYou begin
•You must set up the hardware and install the Brother Drivers before you can use your MFC as a printer and scanner in any Windows®application.
•Please purchase the appropriate cable if you intend to use USB.
Use only a shielded parallel interface cable that is IEEE 1284-compliant and/or a USB cable that is no longer than 6 feet long (1.8 meters)
.
Follow the instructions in this guide for your operating system and interface.
Step 1.
Turn the MFC power switch OFF and disconnect your MFC from your computer if you
already connected an interface cable.
Step 2.
Turn on your computer.
For Windows®2000 Professional, you must be logged on as the Administrator.
Step 3.
Insert the CD-ROM into the CD-ROM drive.
*1 MFC Software Suite includes Printer Driver, Scanner Driver, ScanSoft™
PaperPort®, ScanSoft™Text Bridge®software, Remote Setup and True Type
fonts. PaperPort®is a document management application for viewing
scanned documents. ScanSoft™TextBridge®, which is integrated into
PaperPort®, is an OCR application that converts an image into text and
inserts it into your default word processor package.
3. Click Install Software.
8. When the Choose Destination
Location window displays the path
where the PaperPort®files will be
installed, either change or accept,
and then click Next.
12. The Connect Cable window will
appear.
4. Click MFC Software Suite in Main
Application. Please see Note*1.
9. When the Register Today screen
appears, click Next.This is
registration for Paper Port®. Follow
the instructions.
6. The InstallShield Wizard Setup
window will appear briefly, followed
by the PaperPort®Setup window.
Click Yes.
10. When the MFC Software Suite
Installation window appears, click
Next to begin installing the MFC
Software Suite. Please see Note*2.
1. Insert the MFC Software Suite CD-
ROM into your CD-ROM drive. If the
model name screen appears, click on
your model name.
7. When the PaperPort®Setup window
displays your Name and Company,
either change or accept them, and
then click Next.
11. When the Setup Type window
appears, select Standard, and then
click Next. The application files will
be copied to your computer.
*2 If an error message appears during the
installation process, or you have previously
installed MFC Software Suite or MFL Pro,
you will first have to uninstall it. From the
Start menu, select Programs, Brother,
Brother MFL Pro, Uninstall, and then
follow the instructions on the screen.
*3 Even if you select NO, later you will be able
to launch the Brother Control Centre to use
the Scan key. See
AutoLoad the Brother
Control Centre
, Chapter 5 in the Owner’s
Manual on the CD-ROM.
For Parallel
For USB
–2 –
2. Click your language.The CD-ROM
main menu will appear.
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234567890123456789012123456789012345678
1
234567890123456789012345678901212345678901234567
8
1
234567890123456789012345678901212345678901234567
8
1
234567890123456789012345678901212345678901234567
8
1
234567890123456789012345678901212345678901234567
8
1
234567890123456789012345678901212345678901234567
8
1
234567890123456789012345678901212345678901234567
8
1
234567890123456789012345678901212345678901234567
8
12345678901234567890123456789012123456789012345678
Please see NEXT PAGE
5. Click Install.
( For Windows®2000 Professional User )
For Parallel interface cable users
Step 4.
Connect the MFC to your PC with Parallel Cable.
A. Connect the parallel interface cable to the parallel interface port of the MFC and secure the wire clips.
B. Connect the interface cable to the printer port of the computer and secure it with the two screws. For the location of your
computer’s parallel printer port, see the User’s Guide for your computer.
Step 5.
Turn the MFC power switch ON.
Step 6.
The installation of the Brother driver will automatically start.
Follow the instructions on the screen.
1.
In the Connect Cable window,
click Next.
( For Windows®95/98/98SE/Me Users )
2.
When the above screen
appears, click Finish and
wait
as the PC restarts Windows
®
and continues the installation.
3.
Click Yes to have the Control
Centre loaded each time
Windows®is started.The
Control Centre will appear as
an icon in the task tray. If you
click No the Scan keys on the
MFC will be disabled.Please
see Note*3.
1.
In the Connect Cable window,
click Next.
2.
When the above screen
appears, Click Finish and
wait
as the PC restarts Windows®
and continues the installation.
3.
When the Digital Signature
Not Found dialog boxes
appear, click Yes to install the
driver.
4. Click Yes to have the Control
Centre loaded each time
Windows
®
is started.The Control
Centre will appear as an icon in
the task tray. If you click No the
Scan keys on the MFC will be
disabled. Please see Note*3.
Printer and Scanner drivers have been installed and the
installation is now complete.
Printer and Scanner drivers have been installed and the
installation is now complete.
( For Windows®2000 Users )
For USB interface cable users
Step 4.
Turn the MFC power switch ON.
Step 5.
Connect the Filter Core and Cable Tie to the USB cable,
and then connect the MFC to your PC with the USB cable.
(It will take a few seconds for the installation screen to appear.)
Step 6.
The installation of the Brother driver will automatically start.
Follow the instructions on the screen.
1.
In the Add Printer Wizard
window, select BRUSB:
USB Printer Port, and then
click Next.
( ForWindows®98/98SE/Me Users )
2.
Accept the default Printer
name by selecting Yes, and
then click Next.
4.
If the test page is printed
correctly, click Yes.
If you click No, follow the
prompts on the screen to
correct the problem.
1.
When the Digital Signature Not
Found dialog boxes appear, click
Yes to install the driver.
3.
Select Yes (recommended),
and then click Finish. A test
page will be printed so you
can check the print quality.
5.
Select Yes to restart your
computer, and then click
Finish.
Printer and Scanner drivers have been installed and the
installation is now complete.
2.
Select Finish to restart your
computer.
Printer and Scanner drivers have been installed and the
installation is now complete.
6.
Click Yes to have the Control
Centre loaded each time
Windows®is started.The
Control Centre will appear as
an icon in the task tray. If you
click No the Scan keys on
the MFC will be disabled.
Please see Note*3.
3.
Click Yes to have the Control
Centre loaded each time
Windows®is started.The Control
Centre will appear as an icon in
the task tray. If you click No the
Scan keys on the MFC will be
disabled.Please see Note*3.
–3 –
Version A
Install Software
You can install printer and scanner drivers and the various utility
items.
Manuals
View the Owner’s Manual and other documentation.
Brother Solutions Centre
Connect to the Brother Solutions Centre, the Service and Support
Web Site for your Brother Product.
Further information
Interactive Demonstration showing features of the Printer Driver.
You can get a variety of
information from this
CD-ROM
(For Windows®)
MFC Software Suite Installer
You can install the printer and scanner drivers and the various
utility items.
ReadMe!
You can get important information and troubleshooting tips.
Documents
View the Owner’s Manual and other documentation.
You can get a variety of
information from this
CD-ROM
(For Macintosh®)
Windows®Macintosh®
What is included on the CD-ROM
For Windows NT®Workstation Version 4.0 Users
Step 1.
Check that your computer is
turned on.
You must be logged on as the Administrator.
Step 2.
Connect the MFC to your PC
with the Parallel Cable.
A. Connect the parallel interface cable to the parallel interface port of the MFC and
secure the wire clips.
B. Connect the interface cable to the printer port of the computer and secure it with
the two screws. For the location of your computer’s parallel printer port, see the
User’s Guide for your computer.
12.
Select Yes to restart your computer, and
then click Finish.
13. Click Yes to have the Control Centre
loaded each time Windows is started.
The Control Centre will appear as an
icon in the task bar. If you click No,the
Scan keys on the MFC will be
disabled.Please see Note*3.
For Apple®Macintosh®
QuickDraw
®
Driver for OS 8.6/9.0/9.0.4/9.1 Users
Step 1.
Make sure your MFC power
switch is turned OFF and your
Macintosh is turned ON.
Make sure you do NOT connect your MFC to your Macintosh.
Step 2.
Insert the CD-ROM into your CD-
ROM drive.
Installing MFC Software Suite
Select your language
Step 3.
Restart your Macintosh so it
can recognize the new driver.
1. When the window appears, double-
click MFC Software Suite Installer.
Printer and Scanner drivers have been installed and the
installation is now complete.
Step 3.
Turn the MFC power switch ON.
Step 4.
Follow the instructions on the
screen.
(Same step as Windows 95/98/98SE/Me/2000 Users
Step 3.
, 1-11)
Step 4.
Connect the Filter Core and
Cable Tie to the USB cable.
Step 5.
Connect the MFC to your
Macintosh with the USB cable,
and then turn the MFC power
switch ON.
Step 6.
Select the Printer.
1.
From the Apple menu, open the
Chooser.
2. Click to highlight the printer driver icon
you installed.On the right side of the
Chooser, select the printer to which
you want to print. Close the Chooser.
–4 –
2. Click your language to install the
printer and scanner drivers. After the
installation is completed, the screen
prompts you to restart your Macintosh.
Printer and Scanner drivers have been installed and the
installation is now complete.
Andere Handbücher für MFC-9160
2
Inhaltsverzeichnis
Andere Brother Multifunktionsdrucker Handbücher
Brother
Brother DCP-8040 Bedienungsanleitung
Brother
Brother MFC-8500 Bedienungsanleitung
Brother
Brother DCP 165C - Color Inkjet - All-in-One Bedienungsanleitung
Brother
Brother 9840CDW - Color Laser - All-in-One Bedienungsanleitung
Brother
Brother MFC-J220 Bedienungsanleitung
Brother
Brother DCP-7030 Bedienungsanleitung
Brother
Brother MFC-5895CW Stücklistenhandbuch
Brother
Brother MFC-7840W Bedienungsanleitung
Brother
Brother MFC-J425W Bedienungsanleitung
Brother
Brother MFC-J3520 Installations- und Betriebsanleitung
Brother
Brother MFC-J615W Bedienungs- und Wartungshandbuch
Brother
Brother MFC 3100C - Inkjet Multifunction Bedienungsanleitung
Brother
Brother DCP-770W Bedienungsanleitung
Brother
Brother MFC 5890CN - Color Inkjet - All-in-One Bedienungsanleitung
Brother
Brother DCP-395CN Bedienungsanleitung
Brother
Brother MFC4450 Bedienungsanleitung
Brother
Brother MFC-J5910DW Bedienungs- und Wartungshandbuch
Brother
Brother MFC 8890DW - B/W Laser - All-in-One Bedienungsanleitung
Brother
Brother MFC-J625DW Bedienungs- und Wartungshandbuch
Brother
Brother MFC MFC-5440CN Bedienungsanleitung
Beliebte Multifunktionsdrucker Handbücher anderer Marken
Triumph Adler
Triumph Adler DC 2016 Handbuch
Epson
Epson WorkForce WF-2510 Benutzerhandbuch
Epson
Epson Stylus Scan 2000 Installations- und Betriebshandbuch
Epson
Epson PictureMate Snap PM 240 Bedienungsanleitung
Konica Minolta
Konica Minolta bizhub C35 Bedienungsanleitung
Konica Minolta
Konica Minolta BIZHUB 558 Bedienungsanleitung
