Brother P-Touch D600 Bedienungsanleitung

Read this User’s Guide before you start using your P-touch.

Keep this User’s Guide in a handy place for future reference.

Please visit us at http://support.brother.com/ where you can get product support and

answers to frequently asked questions (FAQs).

www.brother.com

INTRODUCTION

Thank you for purchasing the P-touch D600.

Your new P-touch is an easy to operate, feature packed labelling system that

makes creating professional, high quality labels a breeze.

This manual contains various precautions and basic procedures for using this

labeller. Read this manual carefully before using and keep in a handy place for

future reference.

Federal Communications Commission (FCC) Declaration of Conformity

(For USA Only)

Responsible Party : Brother International Corporation

200 Crossing Boulevard

Bridgewater, NJ 08807-0911, U.S.A.

TEL : (908) 704-1700

declares, that the products

Product Name : Brother P-touch Electronic Labeling System

Model Number : PT-D600

comply with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Important

• The enclosed interface cable should be used in order to ensure compliance

with the limits for a Class B digital device.

• Changes or modifications not expressly approved by Brother Industries, Ltd.

could void the user’s authority to operate the equipment.

International ENERGY STAR®Compliance Statement

The purpose of the International ENERGY STAR®Program is to

promote the development and popularisation of energy-efficient

office equipment. As an ENERGY STAR®Partner, Brother

Industries, Ltd. has determined that this product meets the

ENERGY STAR®guidelines for energy efficiency.

Compilation and Publication Notice

Under the supervision of Brother Industries, Ltd., this manual has been compiled

and published, covering the latest product’s descriptions and specifications.

The contents of this manual and the specifications of this product are subject to

change without notice.

If new versions of the D600 software become available, this manual may not reflect

the updated features. Therefore, you may find that the software and the contents

in this manual are different.

Any trade names and product names of companies appearing on Brother products,

related documents and any other materials are all trademarks or registered

trademarks of those respective companies.

BROTHER is either a trademark or a registered trademark of Brother Industries,

Ltd.

For Australia Only:

Support - For technical support of your Brother Product other than what you can

resolve through the User’s Guide, Please visit our Web Site or support Web Site

(see below) to find an answer to FAQs/Troubleshooting.

Alternatively, please contact the Product Support Centre for any customer care/

technical support enquiry.

To contact Brother International (Aust) Pty Ltd for support on a Brother

product

Please see the details listed below:

Product Support Centre: Australia

Brother International (Aust) Pty Ltd

Phone: 02 8875 6000

Fax: 02 9870 7223

Solutions Site: http://support.brother.com

Web Site: www.brother.com.au

Email: To submit an e-mail enquiry, visit www.brother.com.au, go to

Service and Support area and follow the prompts to contact technical support.

Our Technical Support Consultants are available 5 days a week by phone during

the hours of 8.30am to 5.00pm (EST/EDST) Monday to Friday.

INTRODUCTION

Contents

General Description ............................................................................................... 3

Safety Precautions................................................................................................. 4

General Precautions .............................................................................................. 6

GETTING STARTED.................................................................7

Unpacking Your P-touch ........................................................................................ 7

LCD Display & Keyboard ....................................................................................... 7

Power Supply and Tape cassette .......................................................................... 9

When using AC adapter (AD-E001) ............................................................... 9

When using six new AA alkaline batteries (LR6) or fully charged Ni-MH

batteries (HR6) ............................................................................................... 9

Insert a Tape Cassette ................................................................................. 10

Turning Power On/Off.......................................................................................... 10

Setting Language and Unit .................................................................................. 11

Language...................................................................................................... 11

Unit ............................................................................................................... 11

Turning Tape Colour Detection On/Off ................................................................ 11

Feeding Tape....................................................................................................... 11

Feed & Cut ................................................................................................... 11

Feed only...................................................................................................... 12

How to use the P-touch ....................................................................................... 12

Create a label with the P-touch .................................................................... 12

Create a label by connecting your labeller to a PC ......................................13

Setting Input Mode............................................................................................... 15

Label View Mode .......................................................................................... 15

Print Preview Mode ...................................................................................... 15

EDITING A LABEL ..................................................................16

Entering and Editing Text .................................................................................... 16

Entering Text from the Keyboard.................................................................. 16

Adding a New Line ....................................................................................... 16

Adding a New Block ..................................................................................... 16

Deleting Text ................................................................................................ 16

Inserting a Tab.............................................................................................. 17

Using Text Reminder.................................................................................... 17

Deleting Text Reminder Memory.................................................................. 18

Changing Text Reminder Setting ................................................................. 18

Entering Accented Characters............................................................................. 18

Setting Character Attributes ([Font]/[Size]/[Width]/[Style]/[Line]/[Align]) .............. 19

Setting Character Attributes by Label........................................................... 19

Setting Character Attributes by Each Line.................................................... 19

Setting Auto Fit Style .................................................................................... 21

Setting Frames .................................................................................................... 21

Entering Symbols................................................................................................. 23

INTRODUCTION

Entering Symbols Using the Symbol Function ............................................. 23

Setting Symbol History ................................................................................. 23

Setting Label Attributes ([Length]/[Cut Option]/[Tab Length]).............................. 24

Using Auto-Format Layouts ................................................................................. 25

Using Templates........................................................................................... 25

Using Block Layouts ..................................................................................... 29

Using Table Format ...................................................................................... 32

Printing Transferred Labels (For Windows®)................................................ 33

Creating a Barcode Label....................................................................................34

Setting Barcode Parameters and Entering Barcode Data............................ 34

Editing and Deleting a Barcode.................................................................... 36

Using Time & Date Function ................................................................................ 37

Clock Setting ................................................................................................ 37

Time & Date Format Setting ......................................................................... 37

Time Stamp Setting ...................................................................................... 38

Changing and Deleting the Time & Date Settings ........................................ 40

LABEL PRINTING ...................................................................41

Previewing Labels................................................................................................ 41

Printing Labels ..................................................................................................... 41

Single and Multiple Copy Printing................................................................. 41

Numbering Printing....................................................................................... 42

Mirror Printing ............................................................................................... 42

Setting Tape Cutting Options............................................................................... 42

[Large Margin]/[Small Margin]/[Chain]/[No Cut]/[Special tape] ..................... 42

Adjusting the Label Length .................................................................................. 44

Printing from the Label Collection........................................................................44

Printing a label from the label collection stored in the P-touch..................... 44

Downloading a new Label Collection Category ............................................ 45

USING THE FILE MEMORY ...................................................46

Saving Label Files ............................................................................................... 46

Printing, Opening, Deleting, or Marking a Saved Label....................................... 46

[Print] ............................................................................................................ 46

[Open]........................................................................................................... 46

[Delete] ......................................................................................................... 46

[Marking]....................................................................................................... 47

RESETTING & MAINTAINING YOUR P-TOUCH ...................48

Resetting the P-touch .......................................................................................... 48

Resetting the Data Using the home key ....................................................... 48

Resetting the Data to Factory Settings Using the P-touch Keyboard...........48

Maintenance ........................................................................................................ 49

Cleaning the Unit .......................................................................................... 49

Cleaning the Print Head ............................................................................... 50

Cleaning the Tape Cutter .............................................................................50

INTRODUCTION

General Description

TROUBLESHOOTING ............................................................51

What to do when.................................................................................................. 51

When an error message appears on the display ................................................. 52

APPENDIX ..............................................................................53

Specifications....................................................................................................... 53

System Requirements ......................................................................................... 54

General Description

Tape cassette compartment cover

Tape viewer

LCD display

Tape exit slot Print head

Keyboard

Tape cassette compartment

Tape cutter Release lever

Battery compartment cover

USB port

AC adapter socket

Battery compartment

INTRODUCTION

Safety Precautions

To prevent injury and damage, important notes are explained using various

symbols. The symbols and their meanings are as follows:

The symbols used in this manual are as follows:

WARNING Indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injuries.

CAUTION Indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injuries.

Action NOT allowed DO NOT touch a given portion of

the product.

Mandatory action Unplugging is required

DO NOT disassemble the product. Alerts to the possibility of

electrical shock

WARNING

Follow these guidelines to avoid the risk of fire, burns, injury, electric shocks,

rupture, overheating, abnormal odours or smoke.

Always use the specified voltage

and the suggested AC adapter

(AD-E001) for the P-touch to

prevent any damage or failure.

Do not touch the AC adapter and

P-touch during a thunder storm.

Do not use the P-touch/AC adapter

in places of high humidity such as

bathrooms.

Do not place heavy objects on, or

damage the power cord or plug. Do

not forcibly bend or pull the power

cord. Always hold the AC adapter

when disconnecting from the

power outlet.

Make sure that the plug is fully

inserted to the power outlet. Do not

use an outlet that is loose.

Do not allow the P-touch/AC

adapter/power plug/batteries to get

wet, for example, by handling them

with wet hands or spilling

beverages on to them.

Since loss of eyesight may result

when leaked fluid from batteries

gets into your eyes, immediately

rinse your eyes with a large amount

of clean water, and then seek

medical attention.

Do not disassemble or modify the

P-touch/AC adapter/batteries.

Do not allow a metal object to

contact both the plus and minus

ends of a battery.

Do not use sharp objects, such as

tweezers or a metallic pen, to

change the batteries.

Do not throw the batteries into fire

or expose to heat.

Disconnect the AC adapter and

remove batteries immediately and

stop using the P-touch if you notice

abnormal odour, heat,

discolouration, deformation or

anything unusual while using or

storing it.

INTRODUCTION

Safety Precautions

Do not use a damaged or leaking

battery as the fluid may get on your

hands.

Do not use a deformed or leaking

battery or one whose label is

damaged. There is a possibility of

generating heat.

Do not touch metal parts around

the print head immediately after

printing.

When the P-touch is not being

used, store it out of the reach of

children. In addition, do not allow

children to put the P-touch parts or

labels in their mouths. If any object

has been swallowed, seek medical

attention.

Do not use a damaged adapter

cord or power plug.

Do not use the P-touch when a

foreign object enters the P-touch. If

any foreign object enters the

P-touch, disconnect the AC

adapter and remove the batteries,

and contact Brother customer

service.

DO NOT touch the blade of the

cutter unit.

CAUTION

Follow these guidelines to avoid personal injury, liquid leakage, burns or heat.

If leaked fluid from batteries gets on

your skin or clothes, immediately

rinse them with clean water.

Remove the batteries and

disconnect the AC adapter if you do

not intend to use the P-touch.

Do not use a battery other than that

specified. Do not use combinations

of old and new batteries or

combinations of different types,

different charging levels, different

manufacturers or different models.

Do not insert a battery with the

polarity (+ and -) reversed.

Do not drop or hit the P-touch/AC

adapter.

Do not press on the LCD display.

Do not put your finger inside the

P-touch when you close the tape

cassette compartment cover or

battery compartment cover.

Before using Ni-MH rechargeable

batteries, carefully read the

instructions for the batteries and

battery charger, and be sure to use

them correctly.

When using Ni-MH rechargeable

batteries, charge the batteries with

a specialised battery charger

before using the batteries.

DO NOT open the tape cassette

compartment cover when

operating the cutter unit.

DO NOT apply excessive pressure

to the cutter unit.

WARNING

INTRODUCTION

General Precautions

• Depending on the location, material, and environmental conditions, the label may

unpeel or become irremovable, the colour of the label may change or be

transferred to other objects. Before applying the label, check the environmental

conditions and the material.

• Do not use the P-touch in any way or for any purpose not described in this guide.

Doing so may result in accidents or damage the P-touch.

• Use only Brother TZe tapes with the P-touch. Do not use tapes that do not have

the mark.

• Only use a soft, dry cloth to clean the labeller; never use alcohol or other organic

solvents.

• Use a soft wipe to clean the print head; never touch the print head.

• Do not put any foreign objects into the tape exit slot, AC adapter connector or

USB port, etc.

• Do not place the P-touch/batteries/AC adapter in direct sunlight or rain, near

heaters or other hot appliances, in any location exposed to extremely high or low

temperatures (e.g., on the dashboard or in the back of your car) or high humidity,

or in dusty locations.

• Do not try to print if the cassette is empty; it will damage the print head.

• Do not pull the tape while printing or feeding; it will damage the tape and the

P-touch.

• It is recommended that you use the USB cable supplied with the P-touch. Should

another USB cable need to be used, ensure it is of high quality construction.

• Any data saved in memory will be lost due to failure or repair of the P-touch, or if

the battery expires.

• The P-touch is not equipped with a charging feature for rechargeable batteries.

• The printed text may differ from the text that appears in the LCD.

• The length of the printed label may differ from the displayed label length.

• When power is disconnected for two minutes, all text, format settings and any text

files saved in the memory will be cleared.

• You can also use Heat Shrink Tube in this model. Check the Brother website

(http://www.brother.com/) for further information. You cannot print frames,

pre-set P-touch templates, or use certain font settings when using Heat Shrink

Tube. Printed characters may also be smaller than when using TZe tape.

• Be sure to read the instructions provided with Fabric Tape, Strong Adhesive Tape

or other special tapes and observe all precautions noted in the instructions.

•A protective clear plastic sticker is placed over the display during

manufacturing and shipping. This sticker should be removed prior to use.

Unpacking Your P-touch

GETTING STARTED

Unpacking Your P-touch

LCD Display & Keyboard

Carton Contents

P-touch

Starter Tape Cassette

AC adapter

USB Cable

User’s Guide

8113

87123456

11 12

Print Preview Mode Label View Mode

16 17 18 19 20 21

29 28 27 26 25

The default language is [English].

Andere Handbücher für P-Touch D600

Inhaltsverzeichnis

Andere Brother Etikettendrucker Handbücher

Brother

Brother P-touch PT-D410 Bedienungsanleitung

Brother

Brother P-Touch 580C Bedienungsanleitung

Brother

Brother TD-4000 Bedienungsanleitung

Brother

Brother P-touch PT-2030 Bedienungsanleitung

Brother

Brother VC-500W Bedienungsanleitung

Brother

Brother p900w Betriebsanleitung

Brother

Brother PT1090 - P-Touch - Labelmaker Bedienungsanleitung

Brother

Brother PT-9200 Bedienungsanleitung

Brother

Brother PT-30 Bedienungsanleitung

Brother

Brother P-touch Embellish Bedienungsanleitung

Brother

Brother P-touch 1759 Bedienungsanleitung

Brother

Brother P-touch 2030VP Bedienungsanleitung

Brother

Brother P-TOUCH CUBE XP Bedienungsanleitung

Brother

Brother Stampcreator PRO SC2000USB Bedienungsanleitung

Brother

Brother P-Touch PT-D210 Bedienungsanleitung

Brother

Brother P-touch BB4 Bedienungsanleitung

Brother

Brother PT 1900 - P-Touch Electronic Labeling System Bedienungsanleitung

Brother

Brother QL-1050 Versionshinweis

Brother

Brother P-touch PT-1290 Bedienungsanleitung

Brother

Brother P-Touch PT-D200 Betriebsanleitung

Brother

Brother PT-P750W Bedienungsanleitung

Brother

Brother SC-2000 Bedienungsanleitung

Brother

Brother TD-4650TNWB Bedienungsanleitung

Brother

Brother PT7100 - P-Touch B/W Thermal Transfer... Bedienungsanleitung

Beliebte Etikettendrucker Handbücher anderer Marken

newell

newell Dymo LabelManager 210D Bedienungsanleitung

U-Line

U-Line BROTHER H-8754 Bedienungsanleitung

Tharo Systems

Tharo Systems H-435+ Bedienungsanleitung

Godex

Godex RT700 SERIES Bedienungsanleitung

ID Technology

ID Technology 252 Bedienungsanleitung

Labelmate

Labelmate MC-11 Bedienungsanleitung

CAB

CAB XD4M/300 Bedienungsanleitung

Avery Dennison

Avery Dennison Pathfinder 6057 Service-Handbuch

TSC

TSC PEX1000 Series Bedienungsanleitung

Adkins

Adkins Label Master Bedienungsanleitung

Epson

Epson LabelWorks LW-400 Bedienungsanleitung

Primera

Primera 510212 Bedienungsanleitung

Brady

Brady BradyPrinter S3100 Bedienungsanleitung

DuraLabel

DuraLabel LabPRO Bedienungsanleitung

Novexx Solutions

Novexx Solutions XLP 604 Bedienungsanleitung

Epson

Epson LabelWorks LW-400 Bedienungsanleitung

Dymo

Dymo LabelManager 420P Bedienungsanleitung

Epson

Epson LW-PX400 Bedienungsanleitung