Brother Schulze PRETREATmaker III Bedienungsanleitung

PRETREATmaker III

Initial Setup

1. Do not install the nozzles until the very end of the initial setup listed below.

2. Place Deposit Tank (waste tank) on floor behind machine. Attached the hose provided.

Trim the hose so it has no loops or kinks in the hose.

3. Fill the Bottle Distilled Water tank with 1 gallon of distilled water (This is located on the

right hand side of the unit behind the removable door)

4. Put two parts distilled water and one part pretreat in the Precoating tank and swirl

around to fully mix for approximately 1 minute. You may wish to take a paper towel and

cover the breather hole at the back of the tank when doing this to minimize any liquid

coming out of the tank.

5. On the LCD Panel turn on all 4 nozzle zones. Attach the black hose (precoating hose) to

the Distilled Water tank. Press and hold the Precoating button until the distilled water fills

all 4 lines. This needs to be done to remove any air bubbles or containments from the

lines.

6. To load the pretreat reconnect the black line to the precoating tank and pressing the pre-

coating button until the line is full of white solution. This normally will take about 30

seconds for the line to become filled.

7. Insert nozzles into the yellow quick exchange caps placing the rubber washer over the

nozzle. Connect each of the quick exchange/rubber washer/nozzle assemblies onto the

bottom of the black spray valves. They get secured by turning 90 degrees to lock into

place.

Calibration

1. Ensure that the unit is setup in inches by going to maintenance and touching the

American flag if the unit is not currently setup in this manner.

2. Setup conditions as follows. These are a starting points and adjustments may be

necessary. Adjust the pressure and/or volume until you achieve correct gram value.

Condition

Volume

Pressure

Passes

Begin

Length

F1 (Dark)

125% (+25%)

Bidirectional

(Med)

90% (-10%)

Bidirectional

F3 (Light)

125% (+25%)

Unidirectional

GT DIGITAL GARMENT PRINTERS

For Technical Assistance Please Call Toll Free

1-877-4BROTHER or Enter a Support Ticket

3. Weigh a dry shirt and zero it out on a gram scale (press the Tare button), then spray with

each of the above conditions and reweigh the shirt. The goal is to get following coverage

on each shirt

Condition

Volume

F1 (Dark)

31g

F2 (Med)

24g

F3 (Light)

15g

4. After the desired grams are achieved using the chart as a starting point move forward

and change all of the presets again adjusting only the beginning and length. Normally

this would be for example begin 8 and length of 16. This would give full coverage of the

spray area.

Items customer needs to purchase separately

1. 3 gallons distilled water (important - do not use filtered water, must be distilled)

2. Can of silicon spray (LB5). This is a controlled burst type spray so it will no spray

excessive amounts.

3. Ultrasonic jewelry cleaner

4. concentrated jewelry cleaning fluid (ex: Blitz Gem & Jewelry Cleaner)

5. Gram scale

Evening Maintenance

1. Press Water button for 6 seconds to flush nozzles out with distilled water

2. Remove nozzles and follow the instructions to clean the nozzles using a jewelry cleaning

solution and a sonic cleaner.

3. Wipe down inside of machine with paper towels to remove any buildup of pretreat.

4. Power off the machine and gently push the spray carriage back to access the rails, then

clean the rails using a micro fiber swab and apply spray silicon lubricant on each rail that

the carriage travels along being sure to clean the tracks inside of it as well. Once

complete move the spray carriage back to its original position.

Morning Maintenance

1. Agitate the tank of precoating fluid for approximately one minute.

2. Check the waste tank and empty as needed.

3. Check the volume of distilled water and the precoating tank and refill as needed.

4. Reassemble the nozzles and install them in machine.

5. Press Precoating button until the lines turn white and the precoating has reached the

nozzles.

Maintenance Every 2-4 Weeks

1. Switch the pretreat line to the water tank and then press and hold the Precoating button

on the front panel until the lines are filled with distilled water. Once the line is flushed

reattach the black tube to the Precoating tank and attach the clear line to the Water tank.

Maintenance as needed

1. Remove nozzles and place in ultra-sonic cleaner with jewelry cleaning solution and

follow the instructions on the jewelry cleaning bottle.

2. If you notice that the spray pattern becomes weak then it is suggested to replace the

precoating tank filter (2 spares are included).

Your dealer(s)-distributor(s) are your first line of support, please contact them for prompt

assistance. If you do not have a dealer(s)-distributor(s) refer to our website http://www.brother-

usa.com. For additional information contact Technical Support at 1-877-427-6843 or Support

Ticket. Any information within this document is subject to change.

Inhaltsverzeichnis

Andere Brother Drucker Handbücher

Brother

Brother HL-3140CW Installations- und Betriebsanleitung

Brother

Brother HL-1070 Bedienungsanleitung

Brother

Brother HL 1850 - B/W Laser Printer Bedienungsanleitung

Brother

Brother LASER PRINTER HL-2140 Bedienungsanleitung

Brother

Brother P-Touch 2700 Handbuch

Brother

Brother MFC-1810 Bedienungsanleitung

Brother

Brother HL-2220 Bedienungsanleitung

Brother

Brother DCP-7010 Bedienungsanleitung

Brother

Brother HL-2600CN Series Bedienungsanleitung

Brother

Brother HL-1670N Bedienungsanleitung

Brother

Brother MFC-T920DW Bedienungsanleitung

Brother

Brother HL-5240 Bedienungsanleitung

Brother

Brother MFC-L8690CDW Bedienungsanleitung

Brother

Brother MFC-8870DW Bedienungsanleitung

Brother

Brother HL-1070 - B/W Laser Printer Gebrauchs- und Pflegehandbuch

Brother

Brother HL-B2080DW Technisches Handbuch

Brother

Brother HL-L9200CDW Bedienungsanleitung

Brother

Brother HL-1850 Bedienungsanleitung

Brother

Brother MFC-L8900CDW Bedienungsanleitung

Brother

Brother HL-1850 Bedienungsanleitung

Brother

Brother MFC-T920DW Bedienungsanleitung

Brother

Brother HL-2170W Bedienungsanleitung

Brother

Brother DCP-J525W Bedienungs- und Wartungshandbuch

Brother

Brother GT-3 Series Montageanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung