Brunswick GS Series Bedienungsanleitung
1
GS-X v.III Guarding Safety Controller
Hold-to-Run Switch
Packaging
1 ea. 47-142117-000 Pkg. Hold-to-Run Cable Assembly
*1 ea. 47-142118-000 Pkg. Hold-to-Run Switch
1 ea. 47-902601-000 Installation Instructions
* One per Center Item
Tools Required
- Straight(at)ScrewDriver
- Phillips(cross)ScrewDriver
Hold-to-Run Cable Assembly 47-142117-000
TheHold-to-RuncableassemblyprovidesaconnectionontheSafetyControllerfortheHold-to-Run
switch.AcablemustbewiredintoeachsafetycontrollerwhereaHold-to-Runoperationisdesired.Re-
fertoFigure 1.
Figure 1
September 2012 47-902601-000
©BrunswickBowling&BilliardsCorp.2012.Allrightsreserved.
2
Hold-to-Run Cable Installation in the Safety Controller
WARNING! Turn off the main power to the pinsetter at the main electrical panel
and turn “OFF” the main power switch on the safety controller.
1. Removeanddiscardcoverplatefromsafetycontrollerandretainallscrewsforre-use.Referto
Figure 2.
Figure 2
IMPORTANT!: Save all screws.
2. Removethecoverfromthesafetycontroller.
WARNING! Verify all lights inside the safety controller are off before continuing.
3
3. Installhold-to-runcableassemblyintosafetycontrollerwiththe4screwsfromstep1.Referto
Figure 3.
Figure 3
4
4. Wirethehold-to-runcableassemblytosafetycontroller.RefertoFigure 4 and Schematic of
Hold-to-Run Cable Figure 1.
Figure 4
5. Securethecoverremovedinstep4tothesafetycontroller.
5
Hold-to-Run Switch 47-142118-000
The Hold-to-Run switch is a manually operated switch that allows work to be conducted in the GS-X
pinsetterareaswhilethemachineisoperating.RefertoFigures 5 & 6.
Figure 5
Figure 6
NOTE: When the Hold-to-Run switch is not in use, remove it from the safety controller and store in
a secure location.
6
TheHold-to-Runswitchhasthreepositionsthatprovidethreeoperatingmodes.Referto Figure 7.
Figure 7
7
Functional Test of the Hold-to-Run Switch
WARNING! The effectiveness of the Hold-to-Run switch must be tested before
use. Occupy a safe area, outside of the GS-X pinsetter and away from any
dangerous parts or areas that could cause injury.
1. Withthehold-to-runswitchconnectedtothesafetycontroller(refertopage4,Figure6)inposi-
tion1state(off,pushbuttonnotpressed,GS-Xpinsetternotoperating),checkalltheprotective
devices,interlocksandsensorsbeforeanyworkorthedangerousstateofthepinsetterisinitiated.
a. Completelycovereachlightbeamwithatestpiecethatisnottransparent(atleast30mm
[1-3/16”]diameter)atthefollowingpositions:
-Directlyinfrontofthesender
-Inthemiddlebetweensenderandreceiver
-Directlyinfrontofthereceiver
b. Open the rear pinsetter access door with the interlock switch.
c. Open the masking unit interlock switch.
d. Press the emergency stop button.
Eachoftheprecedingindividualtestsmustproducethefollowingresult:
- Duringthelightbeamtestthereceiverfortherelatedsafetyphotoelectricsafetyswitchmust
havenoLEDilluminated.
- Aslongasthelightbeam,interlockoremergencystopswitchisinterrupted,itmustnotbe
possibletoinitiatethedangerousstateofthepinsetter.
2. Operatethehold-to-runswitchandverifyallthreepositions(refertopage5,Figure7)operate
correctlywhiletheGS-Xpinsetterisinthedangerousstate:
Position 1 -Off,pushbuttonnotpressed,GS-Xpinsetternotoperating
Position 2 -Enabled,pushbuttonpressedtocenterposition,GS-Xpinsetteroperational
Position 3 -Disabled,pushbuttonpressedtofulldownposition,GS-Xpinsetternotoperating
3. Operatethehold-to-runswitchintheposition2state(enabled,pushbuttonpressedtocenterposi-
tion)andverifyalltheinterlocksandsensorswillNOT disablethedangerousstateofthepinset-
ter:
a. Completelycovereachlightbeamwithatestpiecethatisnottransparent(atleast30mm
[1-3/16”]diameter)atthefollowingpositions:
-Directlyinfrontofthesender
-Inthemiddlebetweensenderandreceiver
-Directlyinfrontofthereceiver
b. Open the rear pinsetter access door with the interlock switch.
c. Open the masking unit interlock switch.
d. Press the emergency stop button.
DuringeachoftheseteststhepinsettershouldstayoperationalinthedangerousstateWHILE the hold-to-
runswitchisintheposition2state(enabled,pushbuttonpressedtocenterposition).
Inhaltsverzeichnis
Andere Brunswick Controller Handbücher
