Bull NovaScale 9006 Bedienungsanleitung

NovaScale 9006 Server

VGA Kit

Service Sheet

NOVASCALE

REFERENCE

86 A7 82FB 00

September 2009

The following copyright notice protects this book under Copyright laws which prohibit such actions as, but not

limited to, copying, distributing, modifying, and making derivative works.

Printed in France

Trademarks and Acknowledgements

We acknowledge the right of proprietors of trademarks mentioned in this manual.

All brand names and software and hardware product names are subject to trademark and/or patent protection.

Quoting of brand and product names is for information purposes only and does not represent trademark misuse.

The information in this document is subject to change without notice. Bull will not be liable for errors contained

herein, or for incidental or consequential damages in connection with the use of this material.

Servicing the VGA Kit 1

Servicing the VGA Kit

The VGA Kit is located on the Dummy CSI Interconnect Board (DSIB) (E) inside the server

drawer. This kit allows the connection of a VGA Cable to the DSIB board.

Figure 1. Locating the VGA kit

WARNING

This component is NOT hot-swappable.

Note This intervention is performed with the server drawer in the Servicing Position, as

explained below.

Required Tools

M3 Torx screwdriver

Estimated Intervention Time

30 minutes

2 Product Name - Manual Type

Procedure

1. Unpack the new component on a clean ESD-protected work surface.

2. Open the cabinet front door.

3. Power down the server drawer.

4. Open the cabinet rear door.

5. Disconnect the related cables (rear).

6. Place the Server Drawer in the Servicing Position.

1. From the rear of the cabinet, check that all cables connected to the server drawer are

clearly labeled at both ends. Label any cables that lack identification.

2. Extend the two red cable hanger stop pins and turn 90° to lock them into position.

Figure 2. Extending cable hanger stop pins

Servicing the VGA Kit 3

3. From the front of the cabinet, release the two captive screws securing the server drawer

to the cabinet rack (A).

Figure 3. Server drawer rack fixture screws

4. Slowly pull the server drawer forward until the rails are fully extended and locked, taking

care not to snag or loosen connected cables.

Figure 4. Server drawer in the servicing position

4 Product Name - Manual Type

7. Unlock/Open the Front Cover.

1. Press the 2 locking studs (A) on each side of the server drawer to unlock the front cover.

2. Raise the front cover to an angle of 45°.

Figure 5. Front cover raised

8. Remove the Front Cover.

Slide the raised front cover upward and remove it.

Figure 6. Removing the front cover

Servicing the VGA Kit 5

9. Remove the Rear Cover.

1. Slide the rear cover backwards.

Figure 7. Removing the rear cover

2. Lift up and away from the server drawer to remove it.

6 Product Name - Manual Type

10. Disconnect the Rear Right Cable Bundle.

mportant Check that all cables are correctly labeled before disconnecting.

The rear right cable bundle comprises the following cables:

•ILB-PDB 3.3V STBY Cable

•ILB-HDX Signal Cable

•PDB_ILB 12V Cable

•PDB_MTB 12V Cable

1. Remove the PCI separator, if required.

Figure 8. Removing the PCI separator

Servicing the VGA Kit 7

2. Disconnect the cables from the boards:

-PDB_ILB 12V Cable (A) from the ILB

-ILB-PDB 3.3V STBY Cable (B) from the ILB

-ILB-HDX Signal Cable (C) from the ILB

-PDB_MTB 12V Cable (D) from the MTB

Figure 9. Disconnecting the rear right cables

3. Place the cables outside the server drawer. If necessary, free the cables by unclipping the

cable straps.

8 Product Name - Manual Type

11. Disconnect the Rear Left Cable Bundle.

mportant Check that all cables are correctly labeled before disconnecting.

The rear left cable bundle comprises the following cables:

•PDB_MTB 12V Cable

•ILB-PDB 3.3V STBY Cable

•LCP-ILB Mixed Cable

•ILB-HDX Signal Cable

•2 x ILB-HDX SATA Cable

1. Remove the PCI separator, if required.

Figure 10. Removing the PCI separator

Andere Handbücher für NovaScale 9006

Inhaltsverzeichnis

Andere Bull Server Handbücher

Bull

Bull Escala E1-700 Handbuch

Bull

Bull Escala Power7 Series Bedienungsanleitung

Bull

Bull NovaScale 9006 Bedienungsanleitung

Bull

Bull Escala EL260B Bedienungsanleitung

Bull

Bull NovaScale T810 F2 Bedienungsanleitung

Bull

Bull Escala Power5 Series Betriebsanleitung

Bull

Bull Escala EPC400 Kurzanleitung

Bull

Bull NovaScale 5 5 Series Bedienungsanleitung

Bull

Bull NovaScale R440 F2 Bedienungsanleitung

Bull

Bull Escala Power6 Bedienungsanleitung

Bull

Bull NovaScale T860 F2 Bedienungsanleitung

Bull

Bull Escala E5-700 Bedienungsanleitung

Bull

Bull Escala Power7 Series Bedienungsanleitung

Bull

Bull Escala PL 600T Bedienungsanleitung

Bull

Bull ESCALA PL860T/R Gebrauchs- und Pflegehandbuch

Bull

Bull Novascale R423-E2 Bedienungsanleitung

Bull

Bull NovaScale Blade 2040 Series Bedienungsanleitung

Bull

Bull escalata t430 Bedienungsanleitung

Bull

Bull NovaScale T810 E1 Bedienungsanleitung

Bull

Bull Escala Power7 Series Bedienungsanleitung

Bull

Bull Escala EPC400 Bedienungsanleitung

Bull

Bull Escala BL460 Bedienungsanleitung

Bull

Bull NovaScale 3005 Series Bedienungsanleitung

Bull

Bull NovaScale R410 F2 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung