Bullet tools EZ Shear 220 Bedienungsanleitung

Quick Start Guide

for EZ Shear Model #220

for EZ Shear Model #226

A. (4) M6 x 65mm PH Phillips Machine Screws

B. (4) M6 Star Washers

C. (6) M6 x 25mm PH Phillips Machine Screws

1. Power Assembly

1a. Safety Lock pin

2. Handle Assembly

3. Fence

4. Table The Hardware Kit is used in multiple models. Your Shear may not use all of the items listed.

5. Tail

6. Rails x 2

7. Hone Stone

8. Mounting Brackets x 4

9. Hardware Kit

D. (5) M6 x 16mm FH Phillips Machine Screws

E. (4) #10 x 1 FH Phillips Self Tapping Screws

F. (2) M8 x 50mm Hex Bolts

G. (2) M6 Wing Nuts

In the Box: In the Hardware Kit:

A. (8) M6 x 65mm PH Phillips Machine Screws

B. (8) M6 Star Washers

C. (8) M6 x 25mm PH Phillips Machine Screws

1. Power Assembly

1a. Safety Lock pin

2. Handle Assembly

3. Fence

4. Table The Hardware Kit is used in multiple models. Your Shear may not use all of the items listed.

5. Tail

6. Rails x 4

7. Hone Stone

8. Mounting Brackets x 4

9. Hardware Kit

D. (6) M6 x 16mm FH Phillips Machine Screws

E. (4) #10 x 1 FH Phillips Self Tapping Screws

F. (2) M8 x 50mm Hex Bolts

G. (1) M6 Allen Wrench

In the Box: In the Hardware Kit:

Tools needed: #2 & #3 Phillips head screwdrivers and a 1/2” (13mm) socket or wrench.

IMPORTANT! Start all screws BY HAND when assembling your shear. This will help avoid cross-threading.

ASSEMBLING YOUR SHEAR

1. AT TACH R AILS

Attach rails and mounting brackets to Power

Assembly base using Item A machine screws, ﬁtted

with Item B star washers.

2. AT TACH TAI L

Attach tail and mounting brackets to rails using

Item C machine screws. Make sure holes in tail are

facing up.

3. AT TACH TAB LE

A. Attach table to base starting

with front, start screws by

hand, use Item D screws.

B. Attach back of table to tail

using Item E self tapping screws.

Tighten with #2 Phillips.

Tail

4. ATTACH HANDLE:

For 220:

Insert Item F screws and tighten with 1/2”

wrench.

For 226:

Insert Item F screws through back stroke

stop and tighten with Item G hex wrench.

220 226

5. PLACE THE FENCE

For 220:

Your EZ Shear is equipped with an aluminum fence which may be

set to common roof pitches. (4/12, 6/12, 8/12, and 12/12) Simply

align with desired position and press pins into place.

Note: The fence is friction ﬁt (requires eﬀort to insert or remove).

For 226:

Slide ﬁxed clamp into the front quick alignment notch.

For 90° cuts, slide loose clamp into rear alignment notch

and tighten star knob.

For angle cuts:

1) Align edge of fence with the desired angle guide mark

in center of table.

2) Slide loose clamp to edge of table and tighten knob.

220

226

SST CUT GUIDE

Max Thickness = 1” or 25mm

Material List

Siding, Fiber Cement Board

Siding, Pressboard Lap

Siding, Vinyl

Siding, Wood

Trim, OSB

Trim, Fiber Cement

Trim, Vinyl

Shingles, Tar or Wood

For full manuals, warranty info,

accessories, & tips on using and

maintaining your EZ Shear, go to

BulletTools.com or scan

the QR code below.

MAKING CUTS

While gently pushing

handle down, pull Safety

Lock Pin out, lift handle.

Place product on table.

Bring handle down until

blade touches material.

Push handle down until

material is completely cut.

Hayden, ID USA • 208-772-0175

Dieses Handbuch passt für folgende Modelle

Andere Bullet tools Cutter Handbücher

Bullet tools

Bullet tools EZ Shear SST220 Bedienungsanleitung

Bullet tools

Bullet tools SHUT-N-CUT Bedienungsanleitung

Bullet tools

Bullet tools MAGNUM EDGE MS60-1613 Bedienungsanleitung

Bullet tools

Bullet tools CenterFire Shut-n-Cut Bedienungsanleitung

Bullet tools

Bullet tools Paladin MS93-1009 Bedienungsanleitung

Bullet tools

Bullet tools 113-FLR Bedienungsanleitung

Bullet tools

Bullet tools EZ Shear SST 20 Bedienungsanleitung

Beliebte Cutter Handbücher anderer Marken

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Bedienungsanleitung

Makita

Makita DCS552 Bedienungsanleitung

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Bedienungsanleitung

Makita

Makita 4112HS Bedienungsanleitung

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Bedienungsanleitung

Hitachi

Hitachi CM 4SB2 Fehlerbehebungshandbuch

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Bedienungsanleitung

GCC Technologies

GCC Technologies AFJ-24S Bedienungsanleitung

DeWalt

DeWalt XR LI-ION DCS350N Bedienungsanleitung

Baudat

Baudat ES1 Bedienungsanleitung

Mafell

Mafell ZAF 200 Leitfaden

Makita

Makita 4100NH Bedienungsanleitung

Formax

Formax FD 574 Bedienungsanleitung

EINHELL

EINHELL TE-MA 1500 Bedienungsanleitung

Husqvarna

Husqvarna Cut-n-Break K 760 Bedienungsanleitung

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Bedienungsanleitung

TRI tool

TRI tool 301A Bedienungsanleitung

Roller

Roller King 1 1/4 Bedienungsanleitung