Bush Hog PHDHF15 Bedienungsanleitung

PHDHF SERIES PHDHC SERIES

PHDHF-2 SERIES

PHDHF15, PHDHF20, PHDHF30

PHDHF15-2, PHDF20-2

PHDHF30-2, PHDHF35

PHDHC20, PHDHC30, PHDHC35

Published 03/20 Part No. 50074550

OPERATOR’S MANUAL

BUSH HOG®

2501 Griffin Ave.

Selma, AL 36703

334-874-2700

www.bushhog.com

HYDRAULIC PLANETARY

DRIVE DIGGER

This Operator's Manual is an integral part of the safe operation of this machine and must

be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety

and Operation Instructions contained in this manual before operating the equipment. C01-

Cover

$0.00

To the Owner/Operator/Dealer

All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded

operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has

designed this implement to be used with all its safety equipment properly attached to minimize the chance of

accidents.

BEFORE YOU START! Read the safety messages on the implement and shown in your manual. Observe the rules

of safety and common sense!

WARRANTY INFORMATION:

Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration

Form in full and return it to within 30 Days. Make certain the Serial Number of the Machine is recorded on the

Warranty Card and on the Warranty Form that you retain

TABLE OF CONTENTS

SAFETY SECTION .............................................................................................................. 1-1

General Safety Instructions and Practices .........................................................................................................1-2

Operator Safety Instructions and Practices .......................................................................................................1-3

Equipment Operation Safety Instructions and Practices ....................................................................................1-5

Connecting or Disconnecting Implement Safety Instructions and Practices ......................................................1-8

Transporting Safety Instructions and Practices .................................................................................................1-8

Maintenance and Service Safety Instructions and Practices .............................................................................1-9

Storage and Parking Safety Instructions and Practices ...................................................................................1-11

Concluding Safety Instructions and Practices ..................................................................................................1-11

Decal Location - PHDHF Series ......................................................................................................................1-12

Decal Location - PHDHC Series ......................................................................................................................1-13

Decal Location - PHDHF-2 & PHDHF35 Series ...............................................................................................1-14

Decal Location PHDHF, PHDHF-2, PHDHF35, PHDHC Skid Steer Mounts ...................................................1-15

Decal Description .............................................................................................................................................1-16

FEDERAL LAWS AND REGULATIONS ..........................................................................................................1-18

INTRODUCTION SECTION ................................................................................................. 2-1

ASSEMBLY SECTION ........................................................................................................ 3-1

LOADER BUCKET HITCH MOUNT ASSEMBLY (PHDHF & PHDHC) .............................................................3-2

SKID STEER HITCH ASSEMBLY (PHDHF & PHDHC) ....................................................................................3-2

LOADER BUCKET HITCH MOUNT ASSEMBLY (PHDHF-2 & PHDHF35) ......................................................3-3

SKID STEER HITCH ASSEMBLY (PHDHF-2 & PHDHF35) ..............................................................................3-3

ATTACHING AUGER TO GEARBOX OUTPUT SHAFT ...................................................................................3-4

ATTACHING DRIVE MOTOR TO HITCH MOUNT ............................................................................................3-4

BACKHOE HYDRAULIC DRILL UNIT ...............................................................................................................3-4

OPERATION SECTION ....................................................................................................... 4-1

Standard Equipment and Specifications ............................................................................................................4-3

OPERATOR REQUIREMENTS .........................................................................................................................4-5

POWER UNIT REQUIREMENTS ......................................................................................................................4-6

ROPS and Seat Belt ..........................................................................................................................................4-6

Power Unit Safety Devices ................................................................................................................................4-7

Auxiliary Hydraulics ............................................................................................................................................4-7

GETTING ON AND OFF THE POWER UNIT ....................................................................................................4-8

Boarding the Power Unit ....................................................................................................................................4-8

Dismounting the Power Unit ..............................................................................................................................4-9

STARTING THE POWER UNIT .........................................................................................................................4-9

PRE-OPERATION INSPECTION AND SERVICE ...........................................................................................4-10

Power Unit Pre-Operation Inspection/Service .................................................................................................4-11

Digger Pre-Operation Inspection/Service ........................................................................................................4-11

OPERATING THE POWER UNIT AND IMPLEMENT .....................................................................................4-14

Digger Operating Instructions ..........................................................................................................................4-15

Auger Selection Based on Drilling Application .................................................................................................4-16

IMPLEMENT STORAGE .................................................................................................................................4-17

TRANSPORTING THE POWER UNIT AND IMPLEMENT ..............................................................................4-17

Transporting on Public Roadways ...................................................................................................................4-18

Hauling the Power Unit and Implement ...........................................................................................................4-20

TROUBLESHOOTING GUIDE ........................................................................................................................4-21

MAINTENANCE SECTION .................................................................................................. 5-1

LUBRICATION INFORMATION .........................................................................................................................5-2

AUGER MAINTENANCE ...................................................................................................................................5-3

MACHINE INSPECTION ...................................................................................................................................5-3

STORAGE .........................................................................................................................................................5-3

HYDRAULIC LINES, COUPLERS & ADAPTERS .............................................................................................5-4

PROPER TORQUE FOR FASTENERS ............................................................................................................5-4

Safety Section 1-1

SAFETY SECTION

SAFETY

PHDHF / PHDHC 03/20 Safety Section 1-2

SAFETY

General Safety Instructions and Practices

A careful operator is the best operator. Safety is of primary importance to the manufacturer and should be to

the owner/operator. Most accidents can be avoided by being aware of your equipment, your surroundings, and

observing certain precautions. The first section of this manual includes a list of Safety Messages that, if

followed, will help protect the operator and bystanders from injury or death. Read and understand these Safety

Messages before assembling, operating or servicing this Implement. This equipment should only be operated

by those persons who have read the manual, who are responsible and trained, and who know how to do so

responsibly.

The Safety Alert Symbol combined with a Signal Word, as seen below, is used throughout this

manual and on decals which are attached to the equipment. The Safety Alert Symbol means:

“ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!” The Symbol and Signal Word

are intended to warn the owner/operator of impending hazards and the degree of possible injury

faced when operating this equipment.

Indicates an imminently hazardous situation that, if not avoided, WILL result in DEATH OR

VERY SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, COULD result in DEATH

OR SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, MAY result in MINOR

INJURY.

Identifies special instructions or procedures that, if not strictly observed, could result in

damage to, or destruction of the machine, attachments or the environment.

NOTE: Identifies points of particular interest for more efficient and convenient operation or repair.(SG-1)

Practice all usual and customary safe working precautions and above all---remember safety is

up to YOU. Only YOU can prevent serious injury or death from unsafe practices.

READ, UNDERSTAND, and FOLLOW the following Safety Messages. Serious injury or

death may occur unless care is taken to follow the warnings and instructions stated in the

Safety Messages. Always use good common sense to avoid hazards. (SG-2)

Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las

medidas de seguridad. (SG-3)

SAFETY

PHDHF / PHDHC 03/20 Safety Section 1-3

SAFETY

Operator Safety Instructions and Practices

Never crawl under a raised Implement supported solely by the Power Unit boom. Release

of the control lever or mechanical failure will result in the Implement falling and possible

injury or death. Always securely block up the Implement before crawling underneath to

perform repairs and service. (SPU-33)

Never operate the Power Unit or Implement until you have read and

completely understand this Manual, the Power Unit Operator’s Manual,

and each of the Safety Messages found in the Manual or on the Power

Unit and Implement. Learn how to stop the Power Unit engine suddenly

in an emergency. Never allow inexperienced or untrained personnel too

operate the Power Unit and Implement without supervision. Make sure

the operator has fully read and understood the manuals prior to

operation. (SPU-36)

Always maintain the safety signs in good readable condition. If the safety signs are missing,

damaged, or unreadable, obtain and install replacement safety signs immediately. (SG-5)

The operator and all support personnel should wear hard hats, safety

shoes, safety glasses, and proper hearing protection at all times for

protection from injury including injury from items that may be thrown by

the equipment. (SG-16)

PROLONGED EXPOSURE TO LOUD NOISE MAY CAUSE

PERMANENT HEARING LOSS! Tractors with or without an Implement

attached can often be noisy enough to cause permanent hearing loss.

We recommend that you always wear hearing protection if the noise in

the Operator’s position exceeds 80db. Noise over 85db over an

extended period of time will cause severe hearing loss. Noise over 90db

adjacent to the Operator over an extended period of time will cause

permanent or total hearing loss. NOTE: Hearing loss from loud noise

[from tractors, chain saws, radios, and other such sources close to the

ear] is cumulative over a lifetime without hope of natural recovery. (SG-I7)

Always read carefully and comply fully with the manufacturer’s

instructions when handling oil, solvents, cleansers, and any other

chemical agent. (SG-22)

SAFETY

PHDHF / PHDHC 03/20 Safety Section 1-4

SAFETY

Never run the Power Unit engine in a closed building or without adequate ventilation. The

exhaust fumes can be hazardous to your health. (SPU-23)

KEEP AWAY FROM ROTATING ELEMENTS to prevent entanglement

and possible serious injury or death. (SPHD-2)

NEVER put hands on the Post Hole Digger Auger, Gearbox, or Boom to locate the Auger

when there is any sign of rotation of the Driveline or Auger. Post Hole Diggers are

operated by one person from the tractor seat. Keep all bystanders and/or coworkers away

from the Post Hole Digger. (SPHD-4)

Never use body weight to try to push Auger into the ground to prevent entanglement and

possible serious injury or death. (See Operating Instructions for advice on drilling in hard

ground or rocky conditions.) (SPHD-8)

There are obvious and hidden potential hazards in the operation of this Post Hole Digger.

REMEMBER! This machine can be operated on hillsides and slopes and in other rough

conditions which require increased care and increased awareness of the potential hazards

on both the operator’s and any bystander's part. Serious injury or even death may occur

unless care is taken to insure the safety of the operator, helpers, and any bystanders. (SPHD-11)

Always keep a careful lookout and use extreme care when working around overhead

obstructions. Never allow the Auger within 10 feet of any power line. When working close

to overhead power lines exercise caution and consult your electric company for a safe code

of operation. (SPHD-13)

Dig holes only while seated in the Operator’s seat with the seatbelt securely fastened.

Keep all other persons a minimum distance of 10 feet away from the Tractor and Digger.

Always engage the Tractor parking brakes and set the transmission in park when operating

the digger. (SPHD-14)

Never allow children to play on or around Power Unit or Implement. Children can slip or fall

off the Equipment and be injured or killed. Children can cause the Implement to shift or fall

crushing themselves or others. (SPU-24)

SAFETY

PHDHF / PHDHC 03/20 Safety Section 1-5

SAFETY

Equipment Operation Safety Instructions and Practices

NEVER use drugs or alcohol immediately before or while operating the

Power Unit and Implement. Drugs and alcohol will affect an operator’s

alertness and coordination and therefore affect the operator’s ability to

operate the equipment safely. Before operating the Power Unit or Implement,

an operator on prescription or over-the-counter medication must consult a

medical professional regarding any side effects of the medication that would

hinder their ability to operate the Equipment safely. NEVER knowingly allow

anyone to operate this equipment when their alertness or coordination is

impaired. Serious injury or death to the operator or others could result if the

operator is under the influnce of drugs or alcohol. (SPU-25)

Prolonged operation may cause operator boredom and fatigue affecting safe operation.

Take scheduled work breaks to help prevent these potentially impaired operating

conditions. Never operate the Implement and Tractor in a fatigued or bored mental state

which impairs proper and safe operation. (SG-32)

Use extreme caution when getting onto the Implement to perform repairs, maintenance and

when removing accumulated material. Only stand on solid flat surfaces to ensure good

footing. Use a ladder or raised stand to access high spots which cannot be reached from

ground level. Slipping and falling can cause serious injury or death. (SG-33)

Avoid contact with hot surfaces including hydraulic oil tanks, pumps, motors, valves and

hose connections. Relieve hydraulic pressure before performing maintenance or repairs.

Use gloves and eye protection when servicing hot components. Contact with a hot surface

or fluid can cause serious injury from burns or scalding. (SG-34)

Avoid contact with hot surfaces of the engine or muffler. Use gloves and eye protection

when servicing hot components. Contact with a hot surface or fluid can cause serious injury

from burns or scalding. (SG-38)

Do not operate the implement while wearing loose fitting clothing. Entanglement of the

clothing with the rotating elements can result in serious injury or even death. Stay clear of

all rotating elements at all times. (SSP-03)

Never leave the Tractor and Implement unattended while the Implement is in the lifted

position. Accidental operation of lifting lever or a hydraulic failure may cause sudden drop

of unit with injury or death by crushing. To properly park the implement when disconnecting

it from the tractor, lower the stand and put the retaining pin securely in place, or put a secure

support under the A-Frame. Lower the implement carefully to the ground. Do not put hands

or feet under lifted components. (S3PT-1)

SAFETY

PHDHF / PHDHC 03/20 Safety Section 1-6

SAFETY

Be sure you have adequate knowledge of the property you will be working on. Take time to

make yourself aware of any area underwater or underground lines or cables. Contact with

buried lines or cable could result in serious injury or death. (STL-1)

Operate this Equipment only with a Power Unit equipped with an

approved operator Roll-Over Protective Structure (ROPS). Always

wear seat belts. Serious injury or even death could result from falling

off the Power Unit--particularly during a turnover when the operator

could be pinned under the Operator Protective Structure. (SPU-14)

BEFORE leaving the Power Unit seat, always engage the brake and set the Power Unit

transmission in parking gear, disengage the auxiliary hydraulics, stop the engine, remove

the key, and wait for all moving parts to stop. Place the Power Unit shift lever into a low

range or parking gear to prevent the tractor from rolling. Never dismount a Power Unit that

is moving or while the engine is running. Operate the Power Unit controls from the

operator seat only. (SPU-15)

Never allow children to operate or ride on the Power Unit or Implement.

(SPU-17)

Never allow children to operate, ride on, or come close to the Tractor or

Implement. Usually, 16-17 year-old children who are mature and

responsible can operate the implement with adult supervision, if they

have read and understand the Operator’s Manuals, been trained in

proper operation of the tractor and Implement, and are physically large

enough to reach and operate the controls easily. (SG-11)

Do not mount the Power Unit while the Power Unit is moving. Mount the

Power Unit only when the Power Unit and all moving parts are

completely stopped. (SPU-18)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bush Hog Elektrowerkzeuge Handbücher

Bush Hog

Bush Hog PHD2401 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch