Bustec ProDAQ 3120 Bedienungsanleitung

Hardware Manual

ProDAQ 3120

Standard Motherboard

PUBLICATION NUMBER: 3120-XX-HM-0200

Bustec Production, Ltd.

World Aviation Park, Shannon, Co. Clare, Ireland

Tel: +353 (0) 61 707100, FAX: +353 (0) 61 707106

PROPRIETARY NOTICE

This document and the technical data herein disclosed, are proprietary to Bustec

Production Ltd., and shall not, without express written permission of Bustec Production

Ltd, be used, in whole or in part to solicit quotations from a competitive source or used for

manufacture by anyone other than Bustec Production Ltd. The information herein has been

developed at private expense, and may only be used for operation and maintenance

reference purposes or for purposes of engineering evaluation and incorporation into

technical specifications and other documents, which specify procurement of products from

Bustec Production Ltd.. This document is subject to change without further notification.

Bustec Production Ltd. reserves the right to change both the hardware and software

described herein.

-I -

Table of Contents

1. Introduction _______________________________________________________________________ 1

2. Installation________________________________________________________________________ 3

2.1 Unpacking and Inspection _______________________________________________________ 4

2.2 Reshipment Instructions ________________________________________________________ 4

2.3 Preparing the ProDAQ Module __________________________________________________ 5

2.4 Installing a ProDAQ Function Card_______________________________________________ 5

2.5 Removing a ProDAQ Function Card ______________________________________________ 8

2.6 Installing a ProDAQ Plug-in Module ______________________________________________ 8

3. Configuration______________________________________________________________________ 9

3.1 VXIbus Address Space__________________________________________________________ 9

3.2 VXIbus Logical Address _______________________________________________________ 10

4. Theory of Operation _______________________________________________________________ 11

4.1 Accessing the Motherboard _____________________________________________________ 12

4.1.1 Supported Access Types_____________________________________________________ 12

4.1.2 Address Map______________________________________________________________ 13

4.1.3 VXIbus Configuration Registers ______________________________________________ 14

4.2 VXIbus Configuration Registers_________________________________________________ 15

4.2.1 CONFIG _________________________________________________________________ 15

4.2.2 LOGADR ________________________________________________________________ 15

4.2.3 DEVID __________________________________________________________________ 15

4.2.4 STATUS _________________________________________________________________ 16

4.2.5 CONTROL _______________________________________________________________ 16

4.2.6 OFFSET _________________________________________________________________ 16

4.2.7 FCRESET ________________________________________________________________ 17

4.2.8 IRQH ___________________________________________________________________ 17

4.2.9 JTAG ___________________________________________________________________ 18

4.2.10 FCMASK ________________________________________________________________ 18

4.2.11 FCAVAIL________________________________________________________________ 19

4.2.12 FCMOD _________________________________________________________________ 19

4.2.13 FCBLOCK _______________________________________________________________ 19

4.2.14 FCADR__________________________________________________________________ 19

4.2.15 FCMASKOUT ____________________________________________________________ 19

4.2.16 VERSION________________________________________________________________ 19

4.3 Board Specific Registers _______________________________________________________ 20

4.3.1 VoltRefData ______________________________________________________________ 20

4.3.2 VoltRefID ________________________________________________________________ 20

4.3.3 TrigStatus ________________________________________________________________ 20

4.3.4 TrigRapid ________________________________________________________________ 20

4.4 Trigger System _______________________________________________________________ 21

4.5 Interrupt Handling____________________________________________________________ 22

-II -

List of Figures

Figure 1 - Components of a ProDAQ Modular Data Aquisition System ........................................... 3

Figure 2 - Removing the ProDAQ Module Cover............................................................................. 5

Figure 3 - The module assembly..................................................................................................... 7

Figure 4 - Location of Voltage Reference Plug-in............................................................................ 8

Figure 5 - Location of Jumper J1..................................................................................................... 9

Figure 6 - Logical Address Selection............................................................................................. 10

Figure 7 - Motherboard Simplified Schematic................................................................................ 11

List of Tables

Table 1 - Address Map.................................................................................................................. 13

Table 2 - Configuration Registers.................................................................................................. 14

ProDAQ 3120 Standard Motherboard Hardware Manual 3120-XX-HM

1. Introduction

This manual describes the ProDAQ 3120 Motherboard and explains how to install and configure

the ProDAQ 3120 Motherboard with any of the ProDAQ Plug-in Modules and ProDAQ Function

Cards.

The ProDAQ 3120 Motherboard provides a VXIbus interface and common resources like a voltage

reference module (optional), trigger routing capability and additional power regulators for up to

eight ProDAQ function cards. The ProDAQ 3120 Motherboard together with the ProDAQ Function

Cards can be configured to provide any function or combination of functions required for a specific

application.

The ProDAQ 3120 Motherboard is part of the ProDAQ Modular Data Aquisition System, which

consists of the following components:

AProDAQ Motherboard that installs into a VXI slot in a VXIbus chassis. A ProDAQ

Motherboard can be populated with a ProDAQ 3201 Voltage Reference Plug-in Module

(optional) and up to eight ProDAQ Function Cards.

The ProDAQ 3201 Voltage Reference Plug-in Module that installs into the Voltage Reference

Plug-in slot on a ProDAQ Motherboard.

The ProDAQ Function Cards which install into ProDAQ Bus slots on a ProDAQ Motherboard.

The ProDAQ Signal Conditioning Unit can be used together with the ProDAQ Modular Data

Aquisition System to provide various signal conditioning functions and allows for easy connection

to the existing installation.

3120-XX-HM ProDAQ 3120 Standard Motherboard Hardware Manual

Page 2of 28 Copyright, © Bustec Production Ltd.

ProDAQ 3120 Standard Motherboard Hardware Manual 3120-XX-HM

2. Installation

The ProDAQ 3120 Motherboard is shipped in a VXI module enclosure, ready to be installed in a

VXIbus chassis. The function cards can be factory-installed or field-installed later on. The front-

panel is populated with filler panels for each ProDAQ function card slot, which should be left in

place unless a ProDAQ function card is installed in the slot. The ProDAQ function card slots are

arranged in four stacks of two function cards each.

1 - Module Cover (Bottom) 2 - ProDAQ Motherboard 3 - ProDAQ Function Card

4 - ProDAQ Voltage Ref. Plug-in Module 7 - Single Filler Panel 8 - Double Filler Panel

Figure 1 - Components of a ProDAQ Modular Data Aquisition System

3120-XX-HM ProDAQ 3120 Standard Motherboard Hardware Manual

Page 4of 28 Copyright, © Bustec Production Ltd.

2.1 Unpacking and Inspection

Before unpacking the ProDAQ module, check the exterior of the shipping carton for any signs of

damage. All irregularities should be noted on the shipping bill.

The ProDAQ module is shipped in an antistatic package to prevent any damage from electrostatic

discharge (ESD). Proper ESD handling procedures must always be used when packing, unpacking

or installing any ProDAQ module, ProDAQ plug-in module or ProDAQ function card:

Ground yourself via a grounding strap or similar, e.g. by holding to a grounded object.

Discharge the package by touching it to a grounded object, e.g. a metal part of your VXIbus

chassis, before removing the module from the package.

Remove the ProDAQ module from its carton, preserving the factory packaging as much as

possible.

Inspect the ProDAQ module for any defect or damage. Immediately notify the carrier if any

damage is apparent.

2.2 Reshipment Instructions

Use the original packing material when returning a ProDAQ module to Bustec Production Ltd. or

calibration or servicing. The original shipping carton and the instrument's plastic foam will provide

the necessary support for safe reshipment.

If the original anti-static packing material is unavailable, wrap the ProDAQ module in anti-static

plastic sheeting and use plastic spray foam to surround and protect the instrument. Reship in either

the original or a new shipping carton.

ProDAQ 3120 Standard Motherboard Hardware Manual 3120-XX-HM

2.3 Preparing the ProDAQ Module

To install a ProDAQ Plug-in Module or a ProDAQ Function Card as well as to configure the

addressing mode of the ProDAQ 3120 Motherboard, you need to remove the modules top cover.

1 - Module Cover 2 - Cover Screws 3 - Cover Hooks

Figure 2 - Removing the ProDAQ Module Cover

To remove the top cover, remove the undercut flathead and two panhead screws that hold the

cover in place and remove the cover by sliding it out of its position towards the VXIbus connectors

and up. Take special care about the hooks holding it into place. Try not to lift the cover straight up.

See figure 2 for the location of the screws.

To re-install the cover, slide it back into its position by placing the small hooks over their holes and

moving the cover down and forward. Secure the top cover using the three undercut flathead

crews.

2.4 Installing a ProDAQ Function Card

The ProDAQ Function Cards are arranged inside the ProDAQ Module in four stacks of two cards

each. The function cards are mounted face down, e.g. the front-panel connector as well as the

motherboard connectors are underneath the PCB.

3120-XX-HM ProDAQ 3120 Standard Motherboard Hardware Manual

Page 6of 28 Copyright, © Bustec Production Ltd.

To install a ProDAQ Function Card in any of the possible positions, use the following procedure

(See figure 3 for reference):

Remove the top cover of the module as described earlier in this chapter (Fig. 3, Pos. 1).

Remove all screws on the front-panel holding installed function cards or double filler panels in

place (Fig. 3, Pos. 2). Screws holding single filler panels don't need to be removed.

Remove the two panhead screws that mount the front panel to the modules bottom cover (Fig.

3, Pos. 6).

Please take special care of the module handles and the rings (Fig. 3, Pos. 3 and 4), which are

also fixed by those screws. The mounting angle (Fig. 3, Pos. 5) stays fixed to the front panel.

Remove the front panel by moving it forward carefully so as to avoid bending the installed

function cards.

Choose the stack and position (lower or upper) where you want to mount the function card. If

the stack, in which the function card should be installed, is covered by a double filler panel, you

have to remove it before installing the function card.

Remove the three 2.5mm panhead screws and the crinkle washers from the stack's standoffs

(Fig. 3, Pos. 9 and 10 for example).

If you want to install a function card in the upper position of a stack without having a function

card in the lower position, you need to mount both spacers (Fig. 3, Pos. 11) on each standoff. If

the stack is already populated with a function card in the lower position, mount only the bigger

spacer (Fig. 3, Pos. 8) onto each standoff.

Place a bayonet (supplied) on each standoff. Align the function card over these and slide

carefully down. The function card should be held parallel to the modules bottom cover all the

time during its way down.

Fix the function card by mounting the three 2.5mm panhead screws and the crinkle washers

onto each standoff. If you install a function card in the lower position of a stack, you need first

to mount both spacers (Fig. 3, Pos. 11) onto each standoff.

Re-mount the modules front-panel. If there is only one function card mounted in a stack, cover

the remaining opening in the front panel by a single filler panel.

Re-mount the modules top cover.

Inhaltsverzeichnis

Andere Bustec Hauptplatine Handbücher

Bustec

Bustec ProDAQ 3150 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung