Buzzaudio REQ-2.2 Bedienungsanleitung

REQ-2.2 Resonance Equalizer

Users Manual

REQ

2.2

USERS MANUAL VERSION

4, MAY 2014

. CONTEN

TS COPYRIGHT BUZZ AUDIO LTD 2008

PO BOX 6677, TE ARO. WELLINGTON, NEW ZEALAND. PH. +64-4-472-3084

www.buzzaudio.com email management@buzzaudio.co.nz

Welcome…

Thank you for choosing the Buzz Audio REQ-2.2 Resonance Equalizer. In this

manual you will find important information regarding the use of the REQ

and we suggest you do read it before using the unit to become familiar

with all the controls and their function.

If after unpacking the REQ you find any damage to the unit you should

contact your dealer or supplier immediately for advice on what to do.

We also suggest you retain the original packaging at least during the

warranty period in case you need to return the unit for service, however we

are confident this will not be necessary!

Contents…

Page

1] Installation Precautions.......................................................3

2] The Mains Input ..................................................................3

3] Audio Connections.............................................................4

4] Overview............................................................................5

5] Controls..............................................................................6

6] Specifications.....................................................................8

7] Warranty/Service Information..............................................9

8] Recall Sheets ...................................................................10

9] Graphs ............................................................................12

1] Installation Precautions

The REQ-2.2 uses discrete Class A audio amplifiers and these along with the

power supply generate a fair amount of heat. Whilst the casing has many

ventilation holes, care should be taken to avoid racking the REQ along side

other units that run hot. If possible, allow ventilation space between the

REQ and other hot running boxes.

If the REQ becomes too hot, internal parameters may change and this may

show up as clicks when switching the EQ bands in and out.

The REQ also uses wound chokes (inductors) and because these are coils of

wire with many turns, they are prone to picking up mains hum and other

noise in the environs. The REQ chokes are contained within steel housings

to minimize hum induction, however avoid mounting the REQ next to

devices with large unshielded power transformers or switching power

supplies.

2] The Mains Input

As a safety precaution your REQ maybe shipped without a mains fuse fitted.

Before use, you must select the correct mains voltage for your local supply

on the rear panel and fit the correct mains fuse type into the fuse draw for

that voltage.

The factory or your dealer may have already set all this up for you but it

pays to check it before powering up the REQ.

Setting the Voltage Selector…

You will need a medium size flat blade screwdriver.

If your local mains voltage is 100V to 120V set the rear panel voltage

selector to 110V.

If your local mains voltage is 220V to 240V set the rear panel voltage

selector to 220V.

PLEASE NOTE - POWERING UP THE REQ WITH THE WRONG VOLTAGE SETTING

MAY CAUSE SEVERE AND PERMANENT INTERNAL DAMAGE!

Selecting the Correct Fuse…

In the supplied accessories bag you will find;

2x 1 Amp slow blow fuses, FIT for 220V to 240V.

2x 2 Amp slow blow fuses, FIT for 110V to 120V.

Slide out the fuse draw below the IEC power inlet using a small flat blade

screwdriver and insert the appropriate fuse into the carrier clip. Note there

is also a position in the carrier for a spare fuse (the square tube bit) and we

suggest you store the second supplied appropriate fuse here.

Fitting the wrong fuse may result in the fuse blowing on power up or

inadequate protection. Fitting a fast blow type fuse may also result in the

fuse blowing on power up.

3] Audio Connections

All the XLR connectors on the rear of the REQ-2.2 are balanced and wired

as follows;

Pin 1 = Chassis Ground

Pin 2 = Signal Hot (+)

Pin 3 = Signal Cold (-)

The REQ will accept both balanced and unbalanced inputs, however we

do recommend the use of balanced lines where ever possible. The REQ

has a “looping” input, allowing you to daisy chain it with another device. It

also has two output connectors (paralleled) enabling you to feed two

separate devices if desired.

The REQ output is designed to

drive balanced loads and

each output leg is driven

directly. If you wish to drive

an unbalanced load, you will

need to use a special

connection whereby only Pin

2 and Pin 1 are used and Pin

3 is left floating, ie, no

connection. In this mode the

signal will be 6dB lower than

in balanced mode.

Alternatively an external

audio transformer could be

used to match the REQ into

the unbalanced load.

PLEASE NOTE: A LONG TERM SHORT CIRCUIT ON PIN 2 AND/OR 3 MAY CAUSE

DAMAGE TO THE REQ OUTPUT STAGE.

4] Overview

The REQ-2.2 is a stereo audio equalizer with four “eq” bands per channel

plus a high pass filter and unique “saturation” module. Front panel controls

allow you to adjust each eq band centre frequency, filter bandwidth (or Q)

and the amount of cut/boost. Each element has it’s own on/off switch

which removes it from the signal path when off.

The high and low bands can be switched from a bell filter to a shelving

filter, and the bandwidth control reverts to a shelf slope control when in

shelf mode. The mid bands can be switched between two frequency

ranges as indicated on the front panel.

There are two versions of the REQ, the standard version and a mastering

version. The differences between the two versions are the high pass filter

turn over frequencies (see graphs at the end of this manual), and the

cut/boost controls. The mastering version utilizes a 23 position stepped

attenuator (+/-8dB range) for the cut/boost control, whilst the standard

version offers a continuously variable +/-16dB range with centre detent.

The REQ uses real chokes and capacitors in a parallel resonant circuit

configuration to generate the eq shapes, and this is why it is called the

Resonance Equaliser. Whilst difficult to implement with adjustable

bandwidth, the sound of these passive resonate circuits is far superior to

that of electronically simulated filters.

Unique to the REQ-2.2 is the saturation module which when engaged, adds

subtle amounts of harmonic distortion to the signal and also alters the low

frequency response (see graphs for detail). The saturation module utilizes a

steel core transformer driven by a “single ended” amplifier to achieve this

effect, and is useful in creating a more “vintage” sound. The effect of the

saturation is dynamic in that the higher the signal level, the greater the

effect will be.

5] Controls

EQ Band Controls

FREQUENCY – each band has a 12 position frequency control which sets

the centre frequency of the filter. The two mid bands have two ranges of

frequency, and the blue lettering applies when the FREQ x2.5 switch is

illuminated. Please note that if the FREQUENCY switch is parked between

clicks (or detents) the ON and FREQ x2.5 pushbuttons will not function.

BANDWIDTH (low mid and high mid) – a 12 position switch to set the width of

the bell filters ranging from 2 octaves to 0.25 octaves wide. See the graphs

at the end of this manual for more detail.

BANDWIDTH/SLOPE (low and high bands) – the low and high bands can be

switched into shelf mode (BELL/SHELF switch illuminated), and the bandwidth

control reverts to a shelf slope control in this mode. Position 2 is a steep

slope whilst position 13 is a more gentle curve. See the graphs at the end

of this manual for more detail.

CUT/BOOST – adjusts the amount of eq applied to the signal. The above

drawing shows the standard version with +/-16dB range. The mastering

version of the REQ has a stepped +/-8dB range.

ON – when this switch is illuminated, the associated eq band is engaged

into the signal path. When switched off, the eq band is completely

removed from the signal path.

PEAK – this red LED will illuminate when levels within the REQ circuitry

approach +22dBu warning of possible internal overload. Levels are

monitored at critical points throughout the REQ signal path.

Master Section Controls

HIGH PASS FILTER – a 6 position switch to select roll off frequency of the high

pass filter (HPF). The associated ON switches engages the filter when

illuminated. The drawing above shows the HPF frequency choices for the

standard version. The mastering version has a different set of frequencies

optimized for stereo program equalisation. See the graphs at the end of

this manual for more detail.

SYSTEM – these switches are used to completely bypass the REQ. When not

illuminated, the REQ input XLR connectors are directly connected to the

output XLR connectors providing a hard wire bypass. Note that the REQ still

does receive signal at it’s input when bypassed.

SATURATION – this 6 position switch selects the type of saturation applied to

signal. The associated ON switches engages the saturation circuit when

illuminated. The saturation control changes the low frequency response of

the REQ as well as introducing low frequency harmonics generated by the

steel audio transformer. See the graphs and specifications for detail.

SWITCH LINKING – from REQ serial number Q1115, a new system control

board has been fitted which allows the HIGH PASS FILTER, SYSTEM and

SATURATION in/out switches to be linked. Once linked, you only need to

push either the A or B channel switches to change both channels together.

To link the functions, press and hold down any of the six switches for 4

seconds. To un-link, press and hold down again any of the six switches.

6] Specifications

Frequency Response

Measured with all eq bands ON set flat, Saturation and HPF OFF........5Hz to 125kHz +0.2/-3dB

See graphs for typical eq and HPF frequency response measurements.

Harmonic Distortion

At +10dBu, Saturation OFF .......100Hz 0.007%...1kHz 0.004%...10kHz 0.007%...100kHz 0.013%

Saturation ON POS-1 ........................................20Hz 1.5%...100Hz 0.07%...1kHz and up 0.01%

Saturation ON POS-2 ........................................20Hz 1.5%...100Hz 0.14%...1kHz and up 0.01%

Saturation ON POS-3 ........................................20Hz 1.5%...100Hz 0.16%...1kHz and up 0.01%

Saturation ON POS-4 ........................................20Hz 1.6%...100Hz 0.17%...1kHz and up 0.01%

Saturation ON POS-5 ........................................20Hz 1.7%...100Hz 0.18%...1kHz and up 0.01%

Saturation ON POS-6 ........................................20Hz 2.0%...100Hz 0.22%...1kHz and up 0.01%

Maximum Input Level.....................................................................................................+25dBu

Input Impedance ...........................................................................................approx 20k ohms

Maximum Output Level............................................+32dBu balanced…+26dBu unbalanced

Output Impedance...........................................................................................approx 70 ohms

Input Common Mode Rejection (ref 0dBu) .................100Hz -65dB…1kHz -65dB…10kHz -60dB

Noise all bands ON set flat........................................-110dB below max input level A weighted

General

Power requirements .......................................................... 115V/230V selectable on rear panel

Dimensions...................................................................................4U rack mount, 300mm deep

0dBu = 0.775V RMS in these specifications. Specifications are typical of a production unit, and subject to change if

we improve something.

7] Service Information

We are confident that you will receive many years of trouble free operation

from your unit. If however you experience any technical problem with your

REQ, contact your dealer or Buzz Audio for recommendations on what to

do. The modular nature of the REQ construction means most electronic

faults can be easily repaired by swapping out the circuit boards.

For on line support visit our web site; www.buzzaudio.com

Buzz Audio, PO Box 6677, Wellington 6141, New Zealand.

Phone +64+4+472-3084. Email; [email protected]

8] Product Warranty

Disclaimer

Buzz Audio is not liable for any damage to microphones, amplifiers,

consoles, speakers or any other equipment and/or electric shock to

humans that is caused by negligence or improper installation and/or use of

the REQ-2.2 Resonance Equalizer.

Standard Product Warranty

Buzz Audio guarantees the REQ-2.2 Resonance Equalizer to be free of

defective materials and/or workmanship for a period of 1 year (12 months)

from the date of sale, and will replace defective parts and repair

malfunctioning products under this warranty when the defect occurs under

normal installation and use – provided the unit is returned to our factory (or

duly authorised service centre) via prepaid transportation with a copy of

the proof of purchase, ie, sales receipt. This warranty provides that

examination of the returned product must indicate, in our judgement, a

manufacturing defect. This warranty does not extend to any product that

has been subjected to misuse, neglect, accident, improper installation, or

where the date code has been removed or defaced. The standard

warranty is NOT transferable.

Product Warranty Extension

The above Warranty may be extended to a period of 2 years (24 months)

from date of sale provided the enclosed Warranty Registration card is

completed and returned to the office of Buzz Audio within 4 weeks (28

days) from purchase date. Alternatively, you may Register your purchase

on-line at our web-site www.buzzaudio.com. The Extended Warranty is

transferable.

Inhaltsverzeichnis

Andere Buzzaudio Stereo-Equalizer Handbücher

Buzzaudio

Buzzaudio Zodiak Tilt-n-Filter Bedienungsanleitung

Beliebte Stereo-Equalizer Handbücher anderer Marken

Pioneer

Pioneer DEQ-P90 Bedienungsanleitung

Roland

Roland E-660 Bedienungsanleitung

elysia

elysia mpressor Bedienungsanleitung

Free The Tone

Free The Tone PA-1QG Bedienungsanleitung

Kenwood

Kenwood KRC-999II Bedienungsanleitung

AudioBahn

AudioBahn AEX250X Bedienungsanleitung

Onkyo

Onkyo EQ-08 Bedienungsanleitung

Samson

Samson D3500 Bedienungsanleitung

TDM-Audio

TDM-Audio 30GE-2 Bedienungsanleitung

Me WM8 Bedienungsanleitung

Rob Papen

Rob Papen RP-EQ Bedienungsanleitung

Kenwood

Kenwood GE-4030 Bedienungsanleitung

Rane

Rane RE 27 Service-Handbuch

SPL

SPL SX2 Bedienungsanleitung

Rane

Rane MQ 302S Bedienungsanleitung

Aphex

Aphex 9901 Bedienungsanleitung

Klark Teknik

Klark Teknik DN370 Bedienungsanleitung

Behringer

Behringer Ultragraph Pro FBQ6200 Bedienungsanleitung