BWT Domestic R.O. System RO300 Montage- und Wartungsanleitung

1300 720 299

Installation and Service Guide

Domestic R.O. System | RO300

N1UG05

N1IS35

1. 2.

RO300

N1IS35

1. 2.

RO300

N1IS35

1. 2.

RO300

Please read this manual carefully before attempting installation.

[email protected]

www.bwtaustralia.com.au

1300 720 299

CHECKLIST

1RO300 R.O. System

2FCT-4 Faucet

3PA-E-132 Tank - 14 Litre

4CI3212U7S Fitting for faucet connection

5PPSV500822W Ball Valve - 1/4” x 1/4” Speedt (For Tank connection)

6PPSV040808W Ball Valve - 1/4” x 1/4” Tube

7RODC2.5 Drain Clamp

8H0830425 Grey adaptor

9VAZ550 PLV (550kPa)

10 FRCT-800 Flow Restrictor

Qty 1 Teon Tape

Qty 1 Locking Clip 1/4”

Qty 1 Locking Clip 3/8”

Qty 1 Tube Cutter

Congratulations on purchasing the RO300 Reverse Osmosis system,

which delivers superb quality drinking water.

Faucet

Tap connector

Bench top

Sink

Typical RO300 Installation

and Checklist

N1IS35

Cold water tap

To use quick connect ttings: See Fig. D

See Fig. B

See Fig. C

See Fig. A

Drain

1/4” x 1/4”

Ball Valve

(Speedt)

Hydro Pneumatic

Storage Tank

Grey adaptor

Water Flow

Cold water

Stop valve

Cold

water

Inlet

S.S. braided hose

Drain Clamp

Flow Restrictor

Out

White 1/4”

Ball Valve

Please note: Drain line runs along back of RO300

Yellow 1/4”

PLV

1. 2.

Post

Filter

RO300C

Pre

Filter

RO300C

RO Membrane

RO waste tube

connecting to drain

must be straight and

have adequate fall

[email protected]

www.bwtaustralia.com.au

1300 720 299

Correctly maintained, the RO300 will provide many years of

reliable service.

Before you start installation:

1. Water pressure at the installation point should be minimum 350kPa or the RO performance is compromised. Speak

with WFS if mains water pressure is less than 350kPa.

2. Space required; The R.O. assembly requires 500mm high (allowing for cartridge change out) 330mm wide and

140mm deep. The space required often requires any existing shelf to be modied or removed.

3. The storage tank used with the RO300 measures 350mm high and 280mm in diameter and should be located near

or within 2 meters from the RO300.

4. Tools required;

For stone benchtops: we recommend contacting a benchtop company or suitably qualied tradesperson to drill the

stone benchtop.

For stainless steel sinks/laminate benchtops, you will require:

1. Power drill and drill bits

2. Phillips head screwdriver

3. Adjustable wrench

4. Hammer and center punch

Installing the Faucet

1. Ensure the faucet location is suitable for your kitchen. A 2” diameter foot print is required

2. Mark the centre with centre punch for the 1/4” pilot hole.

3. Drill the pilot hole.

4. Continue to enlarge hole with larger size drill bit until it is 1/2” (12mm).

5. Clean up any sharp edges.

Mounting the Faucet: FIGURE A

1. Chrome base plates and the rubber washer

slide up the shank to the faucet body.

2. Feed threaded shank through the sink/

benchtop hole and orient the faucet. From

below sink, slide lock washer and hex nut

over threaded shank and tighten with a

wrench.

Note: It is best to have someone hold the

faucet from above the sink to keep it from

moving out of place when tightening the

nut.

3. Fit the faucet connector to the base of the

shank

Metal washer

Bench top

Metal washer

Hex nut

Faucet connector

Rubber washer

Chrome base plate

1/2” (12mm)

Figure A

[email protected]

www.bwtaustralia.com.au

1300 720 299

R.O. Unit and Tank Installation

Drain Clamp Installation: FIGURE B

The R.O. unit is normally mounted to the right or left sink cabinet sidewall, depending on where supply tank is to be

located. Generally the unit is installed at the front of the cabinet and the tank at the rear.

To mount the unit, elevate it at least 75mm off the oor, level it and mark the location of mounting holes needed. Drill

hole for mounting screws and install screws allowing the mounting bracket slots to slip over them.

Locate the tank in a suitable location under the sink.

RO300 Tubing

BLUE 3/8” From – Product water from R.O. tank To – Faucet or point of use

WHITE 1/4” From – Cold water supply To – Inlet LHS of pre lter to R.O.

YELLOW 1/4” Supplied water to and from tank.

BLACK 1/4” From – Waste outlet of R.O. membrane To – Drain Connection.

A Drain Clamp is used to make a wastewater connection with the drain under the sink, which is designed to t around

a standard 1-1/2” OD drainpipe. The drain clamp should always be installed before (above) the p-trap and on a vertical

or horizontal drain. Do not install the drain clamp near a garbage disposal to avoid clogging the drain line with debris.

1. Position the drain clamp at selected location and mark for the opening.

2. Drill 1/4” hole at mark through one side of pipe.

3. Position the drain clamp on the drain pipe so the opening aligns with drilled hole. Use a small drill bit to verify that drain

clamp is properly aligned.

4. Secure drain clamp rmly onto the drain pipe.

5. Connect the black drain line of the R.O. into the attached drain clamp assembly.

Drain line

Drain clamp

Use screwdiver

to tighten

Figure B

Upon installation of the RO300, it will take up to one hour

for the tank to ll and the RO300 drain system to shut off

(drain ow to stop)

We recommend draining the rst full tank of R.O. water to

ush the tank and tubing. After this the water will be ready

for use.

Note: If the cabinet sidewalls are not solid, unit may sit on

the oor with screws used just to keep it against the cabinet

in a vertical position

Fit the 1/4” ball valve (speedt) to the top of the tank (use

Teon tape). Do not overtighten.

[email protected]

www.bwtaustralia.com.au

1300 720 299

Ball Valve and Tubing Installation: FIGURE C

Final tubing connections and start up:

The grey inlet adaptor provides a simple, easy connection between the cold water shut-off and the cold water line.

1. Shut-off the cold water supply by using the existing shut-off valve or stop cock, located under your sink. Leave the water

supply off until installation is complete.

2. After shutting off the valve, turn on kitchen tap on the cold water side, this will relieve any excess water and ensure water is

off.

3. Using an adjustable wrench, disconnect the 1/2” braided SS hose line from the cold water shut-off valve.

4. Connect the grey inlet adaptor to the male thread on the cold water shut-off valve. Do not overtighten

5. Reconnect the braided SS braided hose to male thread of the grey adaptor.

6. Connect a length of the 1/4” white tubing between the grey adaptor and the inlet of the R.O. unit.

7. Cut into this line the small quick connect ball valve (turned off) and the pressure limiting valve (PLV).

1. Tubing should follow contour of the cabinets.

2. Cut tubing to correct length using tube cutter provided.

3. Make sure there are no crimps in the tubing.

4. Keep tubing from the R.O. unit to the tank and faucet as short as possible for good ow.

5. Connect blue tube from R.O. to tap connector (or point of use)

6. Leave the yellow tube to ow to atmosphere into a small bucket – so all air is purged through the system.

The isolating valve or stop cock of the mains cold water line can be turned slowly on. The main faucet on the sink will

ow and can now be turned off. The ball valve in the white plastic 1/4” tube should be turned on (tap to run in line with

tube, this is the ON position). Check for leaks. Water will now ll the RO300 and eventually water will slowly discharge

from the yellow tube. When water appears from the yellow tube, t the yellow tube into the ball valve connected to the

top of the pressure tank. The tank will take some time to ll. When the tank is full, water will stop discharging to the

drain. When the faucet is open – or point of use dispenser is used, the RO water will ow from the tank under pressure.

Grey adaptor

Water Flow

Cold water

Stop valve

Cold

water

Inlet

S.S. braided hose

Figure C

[email protected]

www.bwtaustralia.com.au

1300 720 299

Troubleshooting

Membrane

Spare Parts

R.O. Systems are highly sensitive to pressure and temperature. The majority of problems with R.O. Systems are

a result of low pressure. The effects of low pressure include water constantly running to the drain, slow water

production and low water volume available in storage tank. In these cases where low pressure exists, a booster

pump will be required.

To troubleshoot a poor performing R.O. System, an accurate measure of the pressure and temperature of water will

be required. This will require a pressure gauge to determine exactly what the water pressure is that is feeding the

membrane.

FCT-4 Faucet

PA-E-132 Tank - 14 Litre (without valve)

RO300C Pre & Post Filters

ROM75/300TFC Membrane - Only

ROMM300 Membrane - Complete Module

Insert tube

Push up to tube stop

Pull to check secure

Disconnecting

1. Fitting grips before it seals. Ensure tube is pushed into the tube stop.

Push the tube into the fitting, to the tube stop. The collet (gripper) has

stainless steel teeth which hold the tube firmly in position while the O-ring

provides a permanent leak-proof seal.

3. Pull on the tube to check that it is secure. It is a good practice to test

the system prior to leaving site and/or before use.

4. To disconnect, ensure the system is depressurized before removing the

this position, the tube can be removed.

The fitting can then be re-used.

tube. Push in collet squarely against face of fitting. With the collet held in

Note: When removing tube, first remove collet.

How to make a Quick-Connect Connection

The RO300 is tted with a 75US GPD membrane (280 litres per day). Depending on your water pressure and

temperature the production will be 9-12 litres per hour.

[email protected]

www.bwtaustralia.com.au

Inhaltsverzeichnis

Andere BWT Wasserfiltersystem Handbücher

BWT

BWT Quick & Clean Bedienungsanleitung

BWT

BWT PERMAQ mobile 350 Bedienungsanleitung

BWT

BWT bestaqua 16 ROC Bedienungsanleitung

BWT

BWT AVANTI HWS Bedienungsanleitung

BWT

BWT AQA nano Handbuch

BWT

BWT PERMAQ COMPACT 270 Series Bedienungsanleitung

BWT

BWT Planmeca ClinicPatrol Bedienungsanleitung

BWT

BWT PERMAQ compact 4 Handbuch

BWT

BWT Infinity A Bedienungsanleitung

BWT

BWT ROC Clinic One Bedienungsanleitung

BWT

BWT bestaqua 14ROC Bedienungsanleitung

BWT

BWT AQA drink Magnesium Mineralized Water Protect... Bedienungsanleitung

BWT

BWT Haier HB WH-Filter M30D Bedienungsanleitung

BWT

BWT Perla one Bedienungsanleitung

BWT

BWT Protector BW Series Bedienungsanleitung

BWT

BWT TFPKIT Bedienungsanleitung

BWT

BWT AKF 300 Bedienungsanleitung

BWT

BWT Bewades EU Series Bedienungsanleitung

BWT

BWT Woda-Pure Clear S Bedienungsanleitung

BWT

BWT Grohe Blue 40 547 Bedienungsanleitung

BWT

BWT AQA drink MPC400 Bedienungsanleitung

BWT

BWT bestaqua24 HQ Handbuch

BWT

BWT AQA drink Magnesium Mineralized Water Protect... Bedienungsanleitung

BWT

BWT AQA stop Bedienungsanleitung

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung