C.A.P. HUM-1 Bedienungsanleitung

HUM-1 Humidity Controller

CAP offers a full range of equipment for the growing enthusiasts. The HUM-1 is designed to

control the humidity level in your growing area. The unit can be used to either increase or

decrease the humidity level by activating a humidifier to add humidity or an exhaust fan /

dehumidifier to reduce the humidity level. Simple to use and reliable… the HUM-1.

Two

receptacles

Fuse

Humistat

 The HUM-1 controls humidity by activating any

device that operates on 120 volt AC.

 Two receptacles allow you to use the unit to

increase OR decrease humidity levels.

 The HUM-1’s indicator lights verifies the humidity

equipment is running.

 The HUM-1 is backed by CAP’s 3-year warranty.

CONNECTION DIAGRAM

Exhaust Fan or

dehumidifier

HUM-1

Dehumidify

Humidify

Power

Humidifier

CONNECTIONS & OPERATION

There are certain steps which should be taken to ensure a successful installation of your HUM-1.

1) Determine the desired location for the HUM-1. It should be at plant height and near a 120vac power

supply.

2) Mount the HUM-1 to a wall or other vertical surface. The ventilation slots must be oriented on the top and

bottom of the unit.

3) Depending on whether you will be using the unit for humidification OR de-humidification, the device you

will be using must be plugged into the correct receptacle.

4) Adjust the humistat to the desired highest level you want to maintain anywhere from 20-80% rH.

* Verify the device you will be using to add or remove humidity has the capacity to raise or lower the

level adequately. If the device is not large enough, the HUM-1 will command the device to stay on

indefinitely.

5) Connect the power cord to a source of 120-vac power. * Maximum load = 15 amps.

* NOTE: The HUM-1 requires “free air movement” to maintain humidity accuracy. The top and bottom of

the enclosure has ventilation slots to provide air-flow for the internal humistat. We recommend using an

oscillating fan or similar air movement device to provide fresh air for the plants, and the sensor.

TROUBLESHOOTING

If you are having problems with this unit, refer to these troubleshooting hints. Also, refer to the connection

diagram to ensure your devices are connected properly.

Problem Suggested Action

♦ I have no lights and no function at all. ♦ Check fuse or main power. Check the main power plug and replace the fuse if

required with the correct rated fuse.

♦ If the fuse blows repeatedly, verify the devices connected to the unit are working

properly and that they are not too large for the HUM-1 to safely control.

♦ The device I am using rarely or never turns

OFF.

♦ In order for the HUM-1 to turn ON and OFF the device, it must be capable of

raising or lowering the level to the set-point you have selected. If your set-point is

either too high or too low, the unit will be commanded to remain on. If you cannot

achieve the humidity level you would like, you may have to choose a device with a

higher capacity.

♦ The device I am using rarely or never turns

ON.

♦ Once you select the humidity level you want to maintain, the unit will automatically

keep it at that level. If the unit is not turning the unit ON, it is indicating the humidity

is within the acceptable range of +/- 7% rH.

PRECAUTIONS

1) DO NOT expose the HUM-1 to water. The plastic enclosure is corrosion-proof, it is not water-proof.

2) DO connect the HUM-1 to a source of dedicated 15-amp / 120 vac power.

WARRANTY

The HUM-1 is warranted against defects in workmanship for THREE years.

SPECIFICATIONS

Main power voltage 120vac

Maximum amperage 15-Amps @ 120vac

Humidity control range 20 - 80% RH with a 5% differential, +/- 7%

Operating temperature range 32-120° F

Operating humidity range 0-99% RH (non-condensing)

Relay operations (minimum) 100,000 electrical / 1,000,000 mechanical

Weight Less than 4 lbs

Dimensions 8” X 6” X 3.5”

PUBLISHED BY R & M Supply Inc.

Liability statement:

R & M Supply and their retailers and distributors are not responsible for any damage or injuries (consequential or otherwise)

arising from the use of this device. The purchaser assumes all responsibility for the use and proper installation of this device.

Inhaltsverzeichnis

Andere C.A.P. Controller Handbücher

C.A.P.

C.A.P. PPM-4 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung