Cablematic WIS-Q5300 Bedienungsanleitung
5G CPE User Manual
Page 1 , Total 25
WIS-Q5300 User Manual
V1.0
5G CPE User Manual
Page 2 , Total 25
1. Application
Thank you for your purchase WIS-Q5300 5G CPE Wireless AP。This handbook is to help you know and co
nfigure WIS-Q5300.
2. Configuration Preparation
2.1 Installation Device
Figure 1
Press the clip of 5G CPE，pull out the cover，stick one end of cable into ETH port; Slide the cover
until the clip locked.
Stick the other end of cable into POE port of power adapter.
Take another cable, stick one end of cable into LAN port of adapter, the other end into computer port.
Power adapter is plugged into outlet to ensure power open.
2.2 Network Settings
Set PC and set IP address as 192.168.1.x（x is 1-254 except 2，to make sure no conflict with other IP of
network.）
Run Web browser, input http://192.168.1.2（default IP address）and enter。
Figure 2，Default username：admin，Password：admin（You can change this password after entering
the system），and then click Login to the system.
5G CPE User Manual
Page 3 , Total 25
Figure 2
3. Configuration Instruction
3.1 Main Page
After logining enter automatically into Main Page, as shown. Status has 3 status label pages, Wireless、
Network and System Page. The below is introduced separately.
5G CPE User Manual
Page 4 , Total 25
Figure 3-1
3.1.1 WIRELESS Page
Radio status box mainly shows work mode and RF information of 5G CPE.
Wireless mode：working mode of 5G CPE, supporting 4 kinds of working mode, AP Mode、
Station Mode、AP WDS Mode and Station WDS Mode；
Radio mode: working mode of Radio, supporting 802.11a/an two kinds of working modes；
Channel/Frequency: Radio current working channel and working frequency；
Channel Width: Radio channel bandwidth ，supporting 20MHz and 40MHz. Channel
bandwidth has great influence to the wireless. Under no interference environment, average
throughput of 40MHz channel bandwidth can reach more than twice of 20MHz channel
bandwidth；
Country Code: country code of current working Radio. Different country code has different
channel and power for Radio supporting；
Tx Power: current Radio transmission power. Transmission power influences directly signal
strength of communication system, so we should guarantee transmission power big enough;
Max Rate: max sending rate of Radio supporting. Different channel bandwidth could affect max
5G CPE User Manual
Page 5 , Total 25
sending rate. If AP and Station can reach to 40MHz channel bandwidth, max sending rate can
reach to 300Mbps, and throughout rate can improve more than twice.
Station status box shows CPE working as Station Mode.
Up/Down: UP means CPE has successfully connected with AP. Down means that CPE has not
SSID: SSID name of AP that CPE is connecting；
BSSID: BSSID address of AP that CPE is connecting ；
Signal Strength: signal strength of AP that CPE is connecting；Signal strength is negative, the
smaller the absolute value of signal strength, the stronger it proves between CPE and AP. When it
transmits in long distance, stronger signal can ensure higher thorough for wireless transmission.
Security: security way of AP that CPE is connecting, CPE supporting None/WEP/WPA-
TKIP/WPA-CCMP/WPA2-TKIP/WPA2-CCMP/WPA mix encryption and WPA2 mix encryption
connecting AP。
Wireless1/2/3/4 status box shows CPE working as AP Mode. 5G CPE supports at
most 4 wireless services, representing Wireless1/2/3/4.
Up/Down: UP means interface of wireless service has started to work, and is providing wireless
access services. And down means it has not.
SSID: SSID of wireless service；
BSSID: BSSID of wireless service broadcast Beacon using
Security: security way of wireless service using, supporting None/WEP/WPA-TKIP/WPA-
CCMP/WPA2-TKIP/WPA2-CCMP/WPA mix encryption and WPA2 mix encryption；
Asso number: asso number of current wireless service.
3.1.2 NETWORK Page
Figure 3-2, mainly shows current network working mode and network parameter.
5G CPE User Manual
Page 6 , Total 25
Figure 3-2
Network Mode of Network Role status box shows current network mode.
Network Mode: device supports 3 kinds of Network Modes, namely Bridge Mode、SOHO Router Mode
and WISP Mode.
We will have a brief introduction to those:
1. Bridge Mode: Bridge Mode is typical 2-layer network mode. CPE ETH port and wireless interface are
working at 2-layer network mode, no independent IP address. For the whole CPE only Bridge port has
IP address.
2. SOHO Router Mode: This mode is typical network mode of home wireless router. The ETH port is
worked as WAN interface, connecting outer net by ETH port, like Internet or enterprise network. This
device connects with public network supporting three ways: static IP address, DHCP dynamic IP
address and PPPoE.
※Attention: Only when CPE works as AP Mode and AP WDS Mode, network mode can be set
as SOHO Router Mode.
3. WISP Mode: This mode is opposite to SOHO Router. It uses wireless interface as WAN to connect
public network and ETH port as 2-layer access port. For this mode we can think CPE as a large
wireless network card.
※Attention: Only when CPE works as Station Mode or Station WDS Mode，network mode can
be set as WISP Mode.
Network Settings status box shows some basic network parameter.
Bridge IP Address: IP address of Bridge interface；
Net mask: net mask of bridge interface IP address；
5G CPE User Manual
Page 7 , Total 25
Bridge Mac：MAC address of bridge interface；
Gateway：gateway IPAddress of bridge interface；
Primary DNS IP：primary DNS address of bridge interface；
Secondary DNS IP：secondary DNS address of bridge interface；
3.1.3 SYSTEM Page
This page mainly shows version, device name and so on, as shown Figure 3-3.
Figure 3-3
Device Name: device name；
Serial Number: device serial NO.；
Software Version: current software version；
Language: current web language；
Time zone: current time zone；
Current time: current time；
Username: username when logining；
3.1.4 Interfaces List
Interfaces list counts send-receive info of all interfaces, as shown Figure 3-4.
5G CPE User Manual
Page 8 , Total 25
Figure 3-4
Interface：listing all interfaces and interface name；
MAC Address：listing MAC address of all interfaces；
Tx Bytes：sending bytes number；
Tx Packet：sending packet ；
Tx Err：sending error packet ；
Rx Bytes：receiving bytes ；
Rx Packet: receiving packet；
Rx Err: receiving error packet.
3.1.5 ARP List
ARP List counts ARP information of device learning, as Figure 3-5.
Figure 3-5
IP: IP address of device learning；
MAC: MAC address corresponding to IP address of device learning；
Interface: interface to IP address of device learning；
Type: interface hardware type of learning ARP.
3.1.6 STAStats List
When CPE works as AP Mode, STA Status List shows STA info of connecting AP, as Figure 3-6
Figure 3-6
BSSID：BSSID of STA connecting wireless services；
Mode：working mode of STA Radio；
5G CPE User Manual
Page 9 , Total 25
AID: connecting ID of STA；
Signal：AP detected RSSI of STA；
Assoc Time：time online of STA；
Tx/Rx Packets：send-receive packets between AP and STA. Tx means sending packets from AP to STA, Rx
means receiving packets from STA to AP；
Tx/Rx Bytes:send-receive bytes between AP and STA. Tx means sending bytes from AP to STA, Rx means
receiving bytes from STA to AP；
Tx/Rx Rate: rate using by send-receive packets between AP and STA. Tx means senidng rate from AP to
STA, Rx means receving rate from STA to AP, in fact it is sending rate of STA.
3.1.7 APStats List
When CPE works as Station Mode, AP Status List shows info of CPE connecting AP, as Figure 3-7
Figure 3-7
SSID: SSID name of AP that CPE is connecting；
BSSID: BSSID address of AP that CPE is connecting；
Mode：Radio work mode of AP that CPE is connecting；
Channel: working channel ofAP that CPE is connecting；
Signal: CPE detected AP RSSI；
Assoc Time：duration online after CPE is connecting AP；
Tx/Rx Packets：send-receive packets between CPE and AP. Tx means sending packets from CPE to AP, Rx
means receiving packets fromAP to CPE；
Tx/Rx Bytes: send-receive bytes between CPE and AP. Tx means sending bytes from CPE to AP, Rx means
receiving bytes from AP to CPE ；
Tx/Rx Rate: rate using by send-receive packets between CPE and AP. Tx means senidng rate from CPE to
AP, Rx means receving rate from AP to CPE, in fact it is sending rate of AP.
5G CPE User Manual
Page 10 , Total 25
3.1.8 Routes List
Routes list shows current routing relationship of device, as Figure 3-8.
Figure 3-8
Destination: destination address and mask;
Gateway：next address against destination address, that is gateway address.
Flags：network type of this routing info;
Interface：interface of this routing info.
3.1.9 PPPoE Information List
PPPoE information list shows connecting state of current PPoE, as Figure 3-9.
Figure 3-9
Server Name：server name of PPPoE server;
Connection Time：time online of PPPoE connection；
Local IPAddress：local IP address of PPPoE client；
Remote IPAddress：remote IP address of PPPoE server；
Primary DNS IP：primary DNS address of PPPoE client；
Secondary DNS IP：secondary DNS address of PPPoE client ；
TX Packets：CPE sending packets by PPP interface；
RX Packets：CPE receiving packets by PPP interface；
TX Bytes: CPE sending bytes by PPP interface；
Inhaltsverzeichnis
Beliebte Modem Handbücher anderer Marken
Davicom
Davicom DM562AP Bedienungsanleitung
EpiValley
EpiValley TATA indicom SXC-1080 Bedienungsanleitung
Zte
Zte WiMAX Bedienungsanleitung
Intelimax
Intelimax MA-2060 Bedienungsanleitung
SMC Networks
SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch
Telstra
Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung
US Robotics
US Robotics 3453C Bedienungsanleitung
MaxTech
MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung
Zte
Zte MF823 Bedienungsanleitung
Four-Faith
Four-Faith F1403 Bedienungsanleitung
Sierra Wireless
Sierra Wireless AIRLINK MP595W Bedienungsanleitung
Gemtek
Gemtek WiMAX WIXFBR-103 Bedienungsanleitung