Cadis Aquavision Control Bedienungsanleitung

User’s Manual

Aquavision Control

Monitoring Module

Contents

1. Introduction .................................................................................................................................... 2

2. Data and actions that are available without pasword .............................................................. 3

2.1. Real time data of the sanitary pipelines and water consumption .................................. 3

2.2 Acknowledging and checking alarms ................................................................................. 4

2.3. Consulting the list of alarms and creating alarm reports................................................. 5

3. Functions and configurations only available with pasword..................................................... 8

3.1. Making a connection with the module ................................................................................ 8

3.2. Modifying network settings .................................................................................................. 8

3.3. Connection with a CADIS Aquavision Master module .................................................... 9

3.4. Centralisation of consumption data by a central computer ............................................ 9

3.5. Modifying the password and user language ................................................................... 10

3.6. Alarm when daily or weekly consumption is exceeded ................................................. 10

3.7. Alarm during a period of no water consumption ............................................................ 11

3.8. Activation of special functions via relay contacts connected to the AV CONTROL module

3.9. Checking whether the module was correctly configured after installation ................. 12

3.10. ................... Setting alarm e-mail, cutting off water supply and buzzer per alarm type. 15

3.11. .......................... The calendar function: cut off or allow water supply with volume limit 16

3.12. ............................................. Configuration with water meter installed on the street side 17

3.13. ......................................................................................... Creation of consumption reports 18

3.14. .............................. Opening and closing the valves by the user via the control module 19

3.15. ................................................... Activating unlimited water consumption via the screen 19

4. ModBus communication ............................................................................................................. 20

5. Amending the IP address .......................................................................................................... 21

2/23 www.cadis.be [email protected]

User’s Manual

Aquavision Control

Monitoring Module

1. Introduction

The Cadis AQUAVISON is a monitoring and control system that continuously measures, analyses and tracks a

building’s water consumption. Installing this system saves you a lot of water and avoids water damage caused by

leaks, creating an efficient and leak-free sanitation infrastructure. The Aquavision Control module in this system is a

registration and leak detection module, which is installed on the main sanitary pipeline. It constantly monitors the

flow in that main pipeline, detects a leak or waste and can automatically cut off the water supply in the event of

major problems to avoid water damage. One electrical shut-off valve is supplied as standard with the module, which

must be fitted on the main sanitary pipeline after the sub water meter. Two additional shut-off valves can be

installed on the branch pipelines (see diagram below). If additional branch pipelines need to be protected against

leaks and water wastage, a second Aquavision Control module must be fitted. For each additional module, three

extra branch pipelines can be protected.

To function properly, the Aquavision Control module must be connected to the pulse output of the sub water

meters that are installed in the separate pipelines in order to monitor consumption.

The touch screen on the module and the built-in web server allow all data and alarms to be followed up on site or

remotely via the network. Alarms and consumption data can be read out normally in a building management system

(BMS) via a ModBus network connection.

An ordinary user without a password can consult all the data on the module, see the alarms and also confirm active

alarms. A user who has a password and can log in can also modify the system parameters and create reports. The

standard user name and password on delivery for log-in are user/user

All the configurations described below can be carried both on the touch screen of the module as well as remotely on

a computer screen via the web browser.

3/23 www.cadis.be [email protected]

User’s Manual

Aquavision Control

Monitoring Module

2. Data and actions that are available without pasword

The user can see the following data and carry out the following actions without firstly logging in with a password:

• consult the data

• confirm the alarms

• consult the alarm page with a summary of all alarms.

2.1. Real time data of the sanitary pipelines and water consumption

If you click in the main menu on the button "Real time data", a screen automatically appears with a summary of the most

important data:

 Name of the module with the serial number

 Date and time with the time of the last read-out

of the water meter underneath

 The date is automatically correctly set if the

module is linked to a network with access to the

Internet.

Indication of the

consumption period and the

normal or alarm state of the

module.

 Temperature and pressure data if fitted and

activated

 Status of external systems that were

connected to this module.

In the table under the grey bars, the user can view the data for the various pipelines and water meters that have been installed.

The data include the pipe diameter, the serial number of the water meter and the name that the user can assign to the pipe.

All information about the shut-off valves per pipeline is

summarised in 2 columns. A green " " under

“Check” means that the automatic check of the valve

that the module itself conducted was successful. The

user can see whether the valve is open or shut and

thus whether the water supply is protected or not.

CONTROL_HL_NL_02032017

4/23 www.cadis.be [email protected]

User’s Manual

Aquavision Control

Monitoring Module

Note: To counter problems with lime scale, the shut-off valve is closed and re-opened weekly; this action is

performed fully automatically and takes place when there is no consumption detected. During this action a check is

also performed to ensure that the shut-off valve is fully closed. If the check of the valve has been conducted without

any problems, this value is OK (green ""). If the check of the valve has failed, then this value is 'error' (red "") and

the shut-off valve should be inspected.

The user can follow all detailed information about the water consumption per pipeline in the right-hand side of the

table. This information concerns the flow, consumption volume and the index of the water meter in m³.

2.2 Acknowledging and checking alarms

An alarm is always shown via a pop-up screen on the touch screen or in the web server page. In the special alarm

page a user with a password can also define the actions that must be linked to an alarm. Possible actions are:

sending an alarm e-mail, cutting off the water supply or activating a buzzer.

Each alarm must be acknowledged by the user, on the touch screen of the module, or remotely on a computer by

clicking the red button. For some alarms with very high consumption, it may be necessary to click

several times to acknowledge. The alarm confirmation time is saved in the module. If you want to acknowledge an

alarm remotely via your computer, you need access to the network to which the control module has also been

linked.

Given that the module constantly adjusts its values to the demands of the building, for certain alarms (very high

values) the user will need to indicate whether it relates to a normal, but high consumption, or whether a leak or

water wastage has indeed occurred. To do so, the user needs to click on the red "Alarm" button when there is a

real alarm or leak, or he must click on the green "False alarm" button if normal, yet high consumption is involved.

The module itself adapts the values for possible alarms after this last action and in the future no alarm will report

for the same consumption values.

5/23 www.cadis.be [email protected]

User’s Manual

Aquavision Control

Monitoring Module

Once the problem has been solved, the user must restart the system by pressing on the red "System restart"

button. The valves that have automatically cut off the water supply will then be automatically re-opened.

N.B.: If you closed a valve manually, you must firstly manually open that valve before you restart the system (see

the instructions later in the manual).

The user can do the restart on the touch screen of the module or remotely via a computer on the same network.

The Aquavision Control Module will then resume normal operation and this is shown by the message 'System

normal".

2.3. Consulting the list of alarms and creating alarm reports

To be able to analyse several alarms that have occurred, the user can view a summary of all alarms on a separate

alarm page. In the main menu select the 'Alarm list" button.

This takes the user to a screen with all the detailed information about the alarms. This screen shows the type of

alarm and when it occurred, the time when the alarm was confirmed and also the time that the problem was solved

and the module was restarted. If it concerned a false alarm, this will be indicated with a "" in the column

concerned. Additional detailed information and comments can be added per alarm by a technician by pressing on

the button. On this detail screen, comments can be added at the bottom about the leak or the repair so that

these are available to everyone:

6/23 www.cadis.be [email protected]

User’s Manual

Aquavision Control

Monitoring Module

On the same alarm screen, the user can easily create alarm reports for a particular period in order to get a better

insight into the alarms or to inform colleagues. This can be done by choosing a start date (click on "From") and end

date (click on "To") and then confirming that this period is correct and that you want to create a report.

Below is a list of possible alarm reports:

Large leak alarm Leak alarm for very large leak e.g. burst pipe

Leak Leak alarm detected that was calculated by the module

Small leak Module detected a small leak

Very small leak Leak alarm for a micro leak (alarm after 24 hours)

Average daily

consumption exceeded

(%)

Alarm report if the daily water consumption is higher than the average

daily consumption + the percentage that you have defined

Average weekly

consumption exceeded

(%)

Alarm report if the weekly water consumption is higher than the

average weekly consumption + the percentage that you have defined

Volume restriction Alarm if the volume, which is set by the user, has been reached,

Alarm leak detection

external system

Alarm report if the external leak detection system sets off an alarm

Valve malfunction Alarm if the functional test with the shut-off valve fails.

7/23 www.cadis.be [email protected]

User’s Manual

Aquavision Control

Monitoring Module

Flow detected with valve

closed Alarm if the valve can no longer fully close

Unstable pressure

measured with valve

closed

Alarm if a loss of pressure is measured when the shut-off valve is

closed. This can indicate a very small leak in the pipe.

Alarm period no

consumption

Alarm report that can indicate a faulty connection with the water

meter.

Water pressure out of

range of pre-set limits

Alarm signal when the pressure exceeds or falls below the pre-set

minimum or maximum limits

Temperature out of

range of pre-set limits

Alarm signal when the temperature exceeds or falls below the pre-set

minimum or maximum limits

Unlimited water

consumption activated Report if the "Unlimited water consumption" mode is activated.

Manual valve closure

Report if a valve is closed by the user via a manual activation on the

module screen

Intrusion alarm active Report if the intrusion alarm was activated

Alarm main water pipe Report when a leak is observed between the street and the building.

8/23 www.cadis.be [email protected]

User’s Manual

Aquavision Control

Monitoring Module

2. Functions and configurations only available with pasword

After installing this module, the sanitary installer has correctly set the basic functions such as pipe diameters, pulse

settings for the water meter, water meter ID, etc. in order to start the module. This is described in separate

installation instructions.

A user with a password can check these settings and modify them as required by logging in with his computer and

following this user's manual. For that purpose, the user must make a connection by means of his web browser with

the web server of the AV Control module. He can do this also via the touch screen of the module.

3.1. Making a connection with the module

To configure and enter the correct settings in the module a connection must be established by your computer with

the AV CONTROL module. For this reason both your computer and the AV CONTROL module must be linked either

directly or via a LAN network of the building on the LAN port. After this an Internet browser must be opened and

the pre-set IP address of the module must be entered in the address bar at the top of the browser:

10.100.100.225

N.B.: To do that the computer must be set in the same IP range. Otherwise no connection can be set up with the

module (see the information at the end of this document on how to adjust the range of your computer). When the

module and the computer are directly connected without using a network, a "crossed" LAN network cable must

always be used.

3.2. Modifying network settings

First of all, check whether the configuration of the module is correctly carried out. The module will only work

correctly if the installer has configured it correctly.

After logging in, a screen appears with the following headings. Click here on the "Configuration" button.

A screen then appears automatically with the Network settings. Check these network settings and amend the data

as necessary for the building in which the module was installed. Always consult a network specialist first for this to

9/23 www.cadis.be [email protected]

User’s Manual

Aquavision Control

Monitoring Module

ensure that you are entering the correct data. Both the network settings of the actual module, and the e-mail

addresses for sending alarms can be set or changed in this screen.

N.B.: If you change the IP address, you must connect with the module via this new IP address. If the wrong data are

entered, this can cause problems with the connection.

2.3. Connection with a CADIS Aquavision Master module

At the bottom of the Network settings page, you can also enter an IP address for the Aquavision MASTER module.

N.B.: This should only be done if a CADIS MASTER module has been installed, which centralises all consumption

data. If not, leave this blank.

2.4. Centralisation of consumption data by a central computer

With this module it is also possible to monitor the water consumption of several buildings centrally via a central

server. If this is the case for this module, the IP address of this central server must be entered in the screen below.

Contact Cadis for additional information about this functionality.

10/23 www.cadis.be [email protected]

User’s Manual

Aquavision Control

Monitoring Module

2.4. Modifying the password and user language

Go to the Device settings:

The user password can be changed here. Note it down and check it first and click on save to change it. Now you can

only log in using your new password. 'User' is then no longer valid.

On this page the user language and the name + the place of the module can be set or modified.

2.5. Alarm when daily or weekly consumption is exceeded

Go to the Device settings (same screen as above)

On the Device settings page a percentage can be entered in excess of the average day usage. The module will send

an alarm or cut off the water supply if the consumption in a day is higher than the average consumption + this

percentage. The same can be done per week. The type of alarm (alarm e-mail or water supply cut-off) is set on the

Alarm configuration page (see later).

Inhaltsverzeichnis

Andere Cadis Steuereinheit Handbücher

Cadis

Cadis AQUAVISION 2DETECT Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung