Canada Docks Do-It-Yourself Bedienungsanleitung
“Do-It-Yourself” Aluminum Docks
Assembly Instructions for
Floating/Ramp Dock Frame
CanadaDocks
TM
Canada
Docks.
ca
TM
Read this manual and related assembly instructions before attempting to assemble the parts
enclosed to ensure that your new CanadaDocks™ system is assembled safely and correctly.
CanadaDocks-Assembly-Instructions-Ver17 08/08/19
Manufactured by: CanadaDocks Inc. 3690 Adjala-Tecumseth Townline RR2 Beeton, ON, Canada L0G 1A0 | 1-877-434-0359 | www.canadadocks.ca |
“Do-It-Yourself” Aluminum Docks
CanadaDocks
TM
CanadaDocks
.
ca
TM
Page 2
Purchased Separately
x2 (4x8 frame)
x2 (4x8 frame)
x14 (4x8 frame)
x2 (4x8 frame)
x2 (8x8 frame)
x4 (8x8 frame)
x20 (8x8 frame)
For Floats
x4
x4
8x8
8x8
4x8
4x8
4x8
#12 3/4 Pan Phil Tek 410-SS
#12 3/4 Pan Phil Tek 410-SS
x2
x8
x7
x14
x2
A
C
D
x20
x16 with ramp
F
B
S
W
x24
H
x20
3/8” 3/8”
1/4” 1/4”
x24
with ramp
For corner braces
E
G
I
T
V
Q
U
R
M
N
O
P
x2
x16 (4x8 frame)
x16 (4x8 frame) x16 (4x8 frame)
x2
x16 (4x8 frame)
x2 (4x8 frame)
x20 (8x8 frame)
x24 (8x8 frame) x24 (8x8 frame)
x24 (8x8 frame)
x4 (8x8 frame)
47”
95”
95”
JOISTS KIT PARTS
FRAME KIT PARTS
FLOAT KIT PARTS
DECKING
For Decking options please see page 12
PARTS LIST
x16
CanadaDocks-Assembly-Instructions-Ver17 08/08/19
Manufactured by: CanadaDocks Inc. 3690 Adjala-Tecumseth Townline RR2 Beeton, ON, Canada L0G 1A0 | 1-877-434-0359 | www.canadadocks.ca |
“Do-It-Yourself” Aluminum Docks
CanadaDocks
TM
CanadaDocks
.
ca
TM
Page 3
A 4’ Aluminum Truss for 4’x8’Dock or Ramp
B 8’ Aluminum Truss for 4’x8’Dock or Ramp; for 8’x8’
CSquare Aluminum Tube
D Corner Brace
E 3/8” Kep Nut
F 3/8” x 3-½” Carriage Bolt
H 1/4” x 3/4” Hex Cap Screw
I Chain Retainer (must be purchased separately)
JOIST KIT PARTS
M 47” Joist for 4x8
N 95” Joist for 4x8 or 8x8
O #12 3/4 Pan Phil Tek Screws for 4x8 or 8x8
R Float 4x8 (4’Floats fpr 4x8 and 8’ for 8x8)
FLOAT KIT PARTS
P Float 4x8 (4’Floats for 4x8 and 8’for 8x8)
Q 3/8”-16 x 3 Carriage Bolt HDG
R 3/8”-16x3 Eye Bolt HDG (comes with nut)
S 3/8” Hex Nut HDG
T 3/8” Split Lockwasher HDG
U 3/8” D-Washer
V Float Plugs
W Washer
*Not included with Ramp
3‘ or 4‘ level
#3 Phillips Drill Measure Tape
Utility Knife
Safety Glasses
Magic Marker
9/16” & 7/16” Deep Socket with
ratchet to suit
Power Drill
Circular Saw
9/16” & 7/16” Box Wrench
Locking Pliers
5 mm
13/32” Drill Bit
5/16” Allen Wrench
TOOLS REQUIRED
PARTS LIST (CON’T)
CanadaDocks-Assembly-Instructions-Ver17 08/08/19
Manufactured by: CanadaDocks Inc. 3690 Adjala-Tecumseth Townline RR2 Beeton, ON, Canada L0G 1A0 | 1-877-434-0359 | www.canadadocks.ca |
“Do-It-Yourself” Aluminum Docks
CanadaDocks
TM
CanadaDocks
.
ca
TM
Page 4
20 Feet
20 Feet
• Make sure you have a safe, at area for assembly, approximately 20’x 20’.
• Double check to ensure that there are no components missing.
A
B
B
B
4x8 8x8
Truss cut-out should face upwards
when assembled to accomodate
the legs
PLEASE NOTE: Ensure you remove
all plastic from the trusses. Removing
plastic becomes dicult after the
frame has been built.
The cut-out on the truss should face
outwards when laying out the
truss pieces.
1
23Corner cut-out
Line up holes of Truss with leg. Insert
3/8” x 3 1/2” Carriage Bolts (F ) 3/8” Hex Nuts (E).
Hand tighten only. Repeat instructions for the
remaining 3 corners.
Place Square Aluminum Tubes (C) at each corner (4 Square Aluminum Tubes for a
Dock/Ramp, 2 - 7”Square Aluminum Tubes and 2 legs for Quick Link Dock). Ensure
that the at edge of each leg is pointed towards the inside of the dock frame.
C
4
F
E
5
INSTRUCTIONS
Layout all four Trusses Pieces. For 8’x8’docks layout place 4 truss pieces of part (B).
For 4’x8’ docks layout and place 2 truss pieces of part(A) and 2 truss pieces of part(B).
Assemble dock with the truss corner cut-outs facing outwards from the frame so that they are facing upwards
when assembled. Ensure corner cut-outs meet on all four sides.
CanadaDocks-Assembly-Instructions-Ver17 08/08/19
Manufactured by: CanadaDocks Inc. 3690 Adjala-Tecumseth Townline RR2 Beeton, ON, Canada L0G 1A0 | 1-877-434-0359 | www.canadadocks.ca |
“Do-It-Yourself” Aluminum Docks
CanadaDocks
TM
CanadaDocks
.
ca
TM
Page 5
ADDING CORNER BRACES (E)
Ensure that the bump of the corner brace is set
towards the bottom of the dock. This ensures the
drain is oriented towards the bottom of the deck.
D
H
G
67
8
Using a 9/16” ratchet, tighten all 3/8”x 3-½” Carriage Bolts (F) and 3/8” K-Locknuts (E) on all square tubing. Using 7/16” ratchet, tighten all
1/4” x 3/4” Hex Cap Screws (H) and 1/4” K-locknuts (G) on corner braces (See image A above). Using a 7/16” ratchet, tighten all 1/4” x 3/4” Hex
Cap and 1/4” K-Locknuts (See image B above).
Using a 7/16” ratchet, tighten all 1/4”x 3/4” Hex Cap and 1/4”
K-Locknuts (See image above).
9
For 4’x8’ Docks add Corner Braces (D) on a 45˚ angle
between Truss (A) and Truss (B). For 8x8 Docks add Corner
Braces (D) on a 45˚ angle between Truss (B) and Truss (B).
Insert 1/4”x 3/4” Hex Cap Screw (H) into existing holes and tighten with 1/4” K-locknut (G). Hand tighten only.
Do this for all 4 Corner Braces(D).
G
H
D
4x8
8x8
A B
CanadaDocks-Assembly-Instructions-Ver17 08/08/19
Manufactured by: CanadaDocks Inc. 3690 Adjala-Tecumseth Townline RR2 Beeton, ON, Canada L0G 1A0 | 1-877-434-0359 | www.canadadocks.ca |
“Do-It-Yourself” Aluminum Docks
CanadaDocks
TM
CanadaDocks
.
ca
TM
Page 6
N
Place joist into the frame. For 4x8 Dock, place a 47”
long joist(M). For 8x8 Dock place a 95” long joist(N).
The procedure for installing joists is the same for 4x8 and 8x8 frames.
The only dierence are the number of joists added to the bottom of
the frame. The 4x8 dock receives 2 joists and the 8x8 receives 5 joists.
For 4x8 Docks measure 24 ¼”from the edge of the joist to the outside of the truss frame
and position truss here. This will ensure that there is a structure to mount the oat to.
Use vice grips or a clamp to hold the joist against the truss frame.
11
11234 5
2
10
12
In the centre of the joist attach joist to the
truss using a #12x3/4” screw (O) and #3
Phillips Drill Bit. Repeat this step for the
opposite.
JOIST INSTALLATION
13
M
14
4x8
24 ¼”
24 ¼”
24 ¼”
24 ¼”
8x8
4x8 4x8
8x8 8x8
Place the second joist 24”from the edge of the dock for both 4x8 and 8x8 docks. Repeat instructions from steps 12 & 13 for this joist.
Ensure the long end of the joist is facing
upwards when placing joists.
CanadaDocks-Assembly-Instructions-Ver17 08/08/19
Manufactured by: CanadaDocks Inc. 3690 Adjala-Tecumseth Townline RR2 Beeton, ON, Canada L0G 1A0 | 1-877-434-0359 | www.canadadocks.ca |
“Do-It-Yourself” Aluminum Docks
CanadaDocks
TM
CanadaDocks
.
ca
TM
Page 7
15 16
Flip the frame. It is recommended to use two or more
persons for this task.
Place the bottom joist. For 4x8 & 8x8 use 95” long joists(N).
For 4x8 Docks, starting at the edge of the small truss measure and mark 16” to the centre of the truss (See image above). For a 8x8 dock place
the initial joist under the pre-drilled holes spaced 16”. PLEASE NOTE: Keep joists oriented in the correct direction as in Step 17.
18
17
1 4
1
2 5
2
3
34 5
Ensure all joists are facing to the outside of the truss frame. 3 joists should be facing outwards to one side of the frame and 2 joists should
be facing outwards to the opposite side (See diagram above). For the 4x4 Dock ensure both joists are facing to the outside of the truss
frame.
16”
16”
4x8
8x8
CanadaDocks-Assembly-Instructions-Ver17 08/08/19
Manufactured by: CanadaDocks Inc. 3690 Adjala-Tecumseth Townline RR2 Beeton, ON, Canada L0G 1A0 | 1-877-434-0359 | www.canadadocks.ca |
“Do-It-Yourself” Aluminum Docks
CanadaDocks
TM
CanadaDocks
.
ca
TM
Page 8
Use locking pliers to hold the joist against the truss frame under the
marked 16” centre(4x8) or pre-drilled hole(8x8).
For 4x8 docks add a #12x3/4” screw in the centre of the joist
under the 16” mark. For 8x8 add a screw to the pre-drilled
holes every 16” on the truss. Repeat Steps 19 & 20 for the
opposite end of joist.
21
19 20
8x84x8
4x8
16”
For 4x8 Docks, starting at the edge of the small truss measure and mark 16” to the centre of the truss (See image above).
Repeat this for the opposite end of the truss. For a 8x8 dock place the remaining joists under the pre-drilled holes spaced 16”
apart from one another. PLEASE NOTE: Keep joists oriented in the correct direction as in Step 17.
CanadaDocks-Assembly-Instructions-Ver17 08/08/19
Manufactured by: CanadaDocks Inc. 3690 Adjala-Tecumseth Townline RR2 Beeton, ON, Canada L0G 1A0 | 1-877-434-0359 | www.canadadocks.ca |
“Do-It-Yourself” Aluminum Docks
CanadaDocks
TM
CanadaDocks
.
ca
TM
Page 9
22 23
Use locking pliers to hold the joist against the truss frame under
the marked 16” centre(4x8) or pre-drilled hole(8x8).
For 4x8 docks add a #12x3/4” screw in the centre of the joist
under the 16” mark created in step 21. For 8x8 add a screw
to the pre-drilled holes every 16”on the truss. Repeat
Steps 22 & 23 for the opposite end of joist.
Place oats on the bottom of the dock. Ensure the oats are placed on the edge of the truss for the dock. Float should be square to the truss
frame (See image above).
24
FLOAT INSTALLATION
CanadaDocks-Assembly-Instructions-Ver17 08/08/19
Manufactured by: CanadaDocks Inc. 3690 Adjala-Tecumseth Townline RR2 Beeton, ON, Canada L0G 1A0 | 1-877-434-0359 | www.canadadocks.ca |
“Do-It-Yourself” Aluminum Docks
CanadaDocks
TM
CanadaDocks
.
ca
TM
Page 10
25
26
Ensuring the oat is secure (use clamps to keep oat in position if necessary). Use a magic marker to create a mark between the slots of
the oat onto the truss frame. Using the reference above mark o every point shown.
8x8 4x8
Using the marks on the truss frame created in step 25 as your location guide drill holes on each mark. PLEASE NOTE: It may be necessary
to remove the oat to drill depending on the clearance of your drill. Be careful not to drill too closely to any joist screws as it will interfere
with assembly of oats to dock.
13/32” DRILL BIT
Inhaltsverzeichnis
