CANTO USA Astro 250 Bedienungsanleitung

V 1.0 4/19/22 1

Innovative Lighting Products

1092 West Atlanta Street, SE • Suite 600 • Marietta, GA 30060 • 888-252-5912 • [email protected] • cantousa.com

CANTO®FOLLOWSPOT

OPERATING INSTRUCTIONS

FOR THE NORTH AMERICAN REGION 120/208V 60 HZ

MODELS COVERED

01207080 Canto®Astro 250

A01607170 Canto®Astro 600

We hope that this product will meet your requirements, but if for any reason this should not be the case, we ask that you

quality products available. The product you purchased has been manufactured with maximum care in construction and

choice of components. If you have received your equipment damaged for any reason beyond our control, please contact

your local dealer who supplied the product to you within 72 hours after receiving our product.

Innovative Lighting Products

Followspot Operating Instructions

V 1.0 4/19/22 2

1092 West Atlanta Street, SE • Suite 600 • Marietta, GA 30060 • 888-252-5912 • [email protected] • cantousa.com

TABLE OF CONTENTS

01. Important Safety Notes ............................................................................... page 3

02. Check box contents ..................................................................................... page 4

03. Mounting the spigot .................................................................................... page 4

04. Mounting the color changer ......................................................................... page 5

05. Mounting the iris diaphragm ........................................................................ page 5

06. Shutter blades ............................................................................................ page 5

07. Adjusting the yoke ...................................................................................... page 5

08. Wiring ...................................................................................................... page 6

09. Voltage ..................................................................................................... page 6

10. Local Control Panel and Operation .............................................................. page 6

11. Menu ........................................................................................................ page 7

11.1 DMX or manual mode ........................................................................... page 7

11.2 DMX address ........................................................................................ page 7

11.3 Dimmer Resolution ................................................................................. page 8

11.4 Lost DMX Signal .................................................................................... page 8

11.5 Strobe ................................................................................................. page 8

11.6 Strobe Speed......................................................................................... page 9

11.7 Dimming curve ..................................................................................... page 9

11.8 Cut off dimming response ....................................................................... page 9

11.9 Dimming behavior ................................................................................. page 10

11.10 Fan Setting ......................................................................................... page 10

11.11 LCD Screen Illumination ....................................................................... page 11

11.12 Temperature control ............................................................................. page 11

11.13 Software version ................................................................................. page 11

11.14 Manual dimmer Type ........................................................................... page 11

11.15 Pro or basic control ............................................................................. page 12

11.16 Factory setting .................................................................................... page 12

11.17 ID REMOTO ....................................................................................... page 12

11.18 Calibration ......................................................................................... page 13

11.19 Exit Hidden menu ................................................................................ page 13

12. Clamp-on mobile digital dimmer .................................................................. page 13

13. Focusing ................................................................................................... page 13

14. Cleaning and maintenance ......................................................................... page 14

15. Spare sparts .............................................................................................. page 14

16. Warranty .................................................................................................. page 14

17. Available accessories ................................................................................. page 15

18. Summary of controls and functions ............................................................... page 16

19. DMX charts ............................................................................................... page 18

19.1 DMX CHART 1 (16 bit dimmer and strobe disabled) .................................. page 18

19.2 DMX CHART 2 (16 bit dimmer inabled, strobe disabled) ........................... page 18

19.3 DMX CHART 3 (strobe functions inabled, 8 bit dimmer) ............................. page 19

19.4 DIMX CHART 4 (16 bit dimmer and strobe inabled) .................................. page 20

Innovative Lighting Products

Followspot Operating Instructions

V 1.0 4/19/22 3

1092 West Atlanta Street, SE • Suite 600 • Marietta, GA 30060 • 888-252-5912 • [email protected] • cantousa.com

CAREFULLY READ THE OPERATING INSTRUCTIONS BEFORE USING THIS FIXTURE.

The instructions given here ensure safe usage of this product. User’s failure to comply with the installation, operation,

maintenance and safety procedures mentioned in this manual as well as those generally applicable to lighting equipment,

may cause the ﬁxture not to perform as expected.

CantoUSA accepts no liability for direct, indirect, incidental, special, or consequential damages resulting from the customer’s

failure to follow the installation, operating, maintenance and safety procedures described in this manual. These limitations

extend to damages for personal injury, property damage, loss of operation, loss of proﬁts, loss of product or loss of time,

whether incurred by the customer, the customer’s employees, or third-party vendors or users.

Apart from the instructions given in this manual, all relevant safety and health standards of the appropriate local city and

state electrical / safety directives must be complied with.

PLEASE SEE OUR GENERAL TERMS OF SALE AND WARRANTY CARD PROVIDED WITH YOUR NEW EQUIPMENT OR

EMAIL US FOR A COPY AT ANY TIME.

1. IMPORTANT SAFETY NOTES

This product may reach high temperatures depending on the model ordered. Avoid any direct contact with its metal exhaust parts.

*NEVER WORK INSIDE AN OPERATING UNIT WITHOUT IT BEING COOLED AND UNPLUGGED FROM

POWER SOURCE. NEVER EVER WORK INSIDE A UNIT THAT IS TURNED ON.

*WARNING: HIGH VOLTAGE IGNITION, DISCONNECT THE UNIT FROM POWER BEFORE SERVICING

* Continuous mains power is required for this spotlight as an internal dimmer controls the intensity via DMX or local rotary

knob. An accessory moving manual dimmer is furthermore available for positioning on the side grab handles.

* Use of a phase control dimmed mains supply may damage the internal electronics.

* This product features fan-assisted ventilation. Make sure you do not cover the fans or obstruct the air ﬂow at any one time.

* Make sure the fans are working correctly. Should you detect even the slightest malfunction, switch the luminaire off and

carry out the necessary servicing. Replace the fans if necessary.

* This product is rated IP 20 and is therefore designed for interior use only. For details on maximum ambient temperature,

minimum distance from ﬂammable objects and tilt angle, please refer to what indicated on the product label.

* Repairing and replacement of any component of this product must be carried out exclusively by professional personnel in

conformity with the relevant safety and health standards and only with original Canto USA components.

* Replacement of any part of the wiring system must be carried out exclusively by professional personnel in compliance with

the original wiring diagram and with components identical to or compatible with those originally ﬁtted.

* Installation of this product must be exclusively carried out by professional personnel

Innovative Lighting Products

Followspot Operating Instructions

V 1.0 4/19/22 4

1092 West Atlanta Street, SE • Suite 600 • Marietta, GA 30060 • 888-252-5912 • [email protected] • cantousa.com

BEFORE YOU GET STARTED, PLEASE READ THIS INSTRUCTION MANUAL

COMPLETELY.

2. CHECKING BOX CONTENTS:

Upon opening the boxes, please make sure the boxes contain the following items:

FOLLOWSPOT:

A. In case you bought just the followspot

1. Fixture:

a. Followspot in the chosen model

b. Separate mains power cable with PowerCon

c. Iris diaphragm

d. 28mm spigot with M12 self locking nut and plain washer

e. Clamp-on digital dimmer A20702071

B. In case you bought the complete kit

a. Followspot in the chosen model

b. Separate mains power cable with PowerCon

c. Iris diaphragm

d. 28mm spigot with M12 self locking nut and plain washer

e. Clamp-on digital dimmer A20702071

TRIPOD STAND:

Tripod – May or may not include casters for the tripod. Casters are an accessory that can be purchased.

3. MOUNTING THE SPIGOT:

Make sure the tripod you are going to use features a (28mm) top aperture for the supplied spigot.

Remove the M12 nut and washer from the spigot and insert the threaded end into the center hole of the yoke of the

followspot from beneath the yoke. Tighten the M12 nut with a suitable tool so that the spigot securely holds the followspot in

place but allows proper movement of the ﬁxture.

Loosen the “T” Handle screw where the spigot inserts into the tripod. Mount the followspot onto the tripod. Place the tripod

in such a manner where the “T” Handle screw runs parallel to the yoke. Make sure the spigot shaft sits 12mm above the

base of the tripod. There is a recess in the spigot shaft just below the base that is a good indication of where to mount the

spigot. Make sure the area you are placing the product on can withstand the product load (see product label to check on

weight) i.e. catwalk or balcony.

Innovative Lighting Products

Followspot Operating Instructions

V 1.0 4/19/22 5

1092 West Atlanta Street, SE • Suite 600 • Marietta, GA 30060 • 888-252-5912 • [email protected] • cantousa.com

4. MOUNTING THE COLOR CHANGER:

1. At the front of the followspot, lossen the 2 phillips screws from one of the two front color runners.

2. Repeat with the second color runner.

3. Mount color ﬁlters on the color changer units. See relevant instructions supplied with the color changer.

4. Position the color changer unit on the front plate of the followspot, making sure that the color levers are positioned

on the right-hand side of the followspot when viewed from behind and hang it to the previously positioned screws.

5. Release the color ﬁlters of the color changer in order to have access to the screws and tighten them.

6. Ensure the color changer unit is secure, and all three screws are tight.

5. MOUNTING THE IRIS DIAPHRAGM:

The iris diaphragm supplied with the followspot has 20 leaves to size the beam from a maximum aperture of 68mm to a

minimum of 5mm. A black-out iris diaphragm is available to special order.

1. Using a Phillips screw-driver remove the two phillips screws from the sides of the iris plate.

2. Slide the diaphragm in the gate area.

3. Tighten the screws.

IMPORTANT NOTICE: DO NOT LEAVE THE IRIS CLOSED FOR OVER 5 MINUTES WHILE THE LED IS ON

FAILURE TO COMPLY WITH THE ABOVE NOTICE MAY CAUSE THE IRIS AND THE FOLLOWSPOT TO SUFFER

MAJOR HEAT DAMAGE AND WILL INVALIDATE THE PRODUCT WARRANTY.

6. SHUTTER BLADES:

Shutter blades are not supplied with the unit, but are available as a separate accessory. They are sold as single items and

the relevant part number is R80208019. 4 are required.

7. ADJUSTING THE YOKE:

This followspot is provided with a yoke balancing adjustment. The balancing point is factory set for a standard usage of

the product conﬁguration supplied (without color); however, should you need to adjust the balancing, please proceed as

follows:

1. The followspot must be mounted on the tripod stand with all relevant accessories attached.

2. Using a Phillips screw-driver, loosen the 2 (M5) screws on each side of the mounting plate of the yoke.

3. Gently slide the followspot backward or forward to the required position.

4. Make sure the yoke is correctly aligned horizontally.

5. Tighten the 4 5mm screws.

Innovative Lighting Products

Followspot Operating Instructions

V 1.0 4/19/22 6

1092 West Atlanta Street, SE • Suite 600 • Marietta, GA 30060 • 888-252-5912 • [email protected] • cantousa.com

8. WIRING:

Before being connected to power, please make sure that the unit is outﬁtted with a suitable plug. Make sure the plug conforms

to the lamp power load. This ﬁxture must be grounded. Ensure the plug conforms to the relevant local safety requirement and

UL electrical standards.

To perform a correct wiring, please note that the cores in this mains lead are color-coded as follows:

Ground: green+yellow – Neutral: blue - Hot: brown

In case the colors of the wires do not correspond to the color of the connection points on your plug, please proceed as follows:

• The green or green and yellow wire is ground and must be connected to the connection point marked with the

letter E or with the symbol or colored in green or in green+yellow

• The blue wire is neutral and must be connected to the connection point marked with the letter N or with the

symbol or colored in black

• The brown wire is hot and must be connected to the connection point marked with the letter L or with the

symbol or colored in red

Before you ﬁnally position this product for use, temporarily connect it to a properly fused power supply to check the lamp

works correctly.

9. VOLTAGE:

Before operating this unit please refer to the product label mounted at the back of the luminaire to

check you are operating with the correct voltage.

The Astro 250 LED and 600 LED can be operated between 120V and 208 V.

10. LOCAL CONTROL PANEL AND OPERATION:

OPERATION: LCD display for DMX address, system setup and status details.

POWER: power LED status indicator , red color. ON= power

DMX: DMX LED status indicator, green color. LED OFF = DMX OFF and manual control activated ,

LED ON = DMX MODE activated with no DMX signal, FLASHING LED = receiving DMX

MENU: rotary switch selector to select and modify the operational modes.

Turn left or right to navigate through the menu and press to select or to conﬁrm

DMX IN: input DMX signal (pin1=0 , pin2= DATA- , pin3=DATA+ ).

DMX OUT : Loop through DMX signal output

POWER IN: Mains power input

POWER OUT: Mains power output

Innovative Lighting Products

Followspot Operating Instructions

V 1.0 4/19/22 7

1092 West Atlanta Street, SE • Suite 600 • Marietta, GA 30060 • 888-252-5912 • [email protected] • cantousa.com

11 MENU:

There are fourteen different menus to control the settings of ASTRO LED. The rotary selector is used to adjust the settings

and to navigate through the menu. Turn left or right to select the menu and push to access or to conﬁrm the selected data or

functions. To exit the selected menus without saving the data, press the rotary selector for at least 1 second.

11.1 DMX OR MANUAL (MODE):

Select the LED control mode between OMX (factory setting) and manual. To change the control mode press once the rotary

selector until an arrow (0) appears on the menu. Turn the selector to the right or the left to select the desired mode of

operation and press to conﬁrm your selection.

Tap the rotary selector and the LCD screen will display the mode status and the current value:

11.2 DMX ADDRESS (ADDR):

It allows to select the initial DMX starting address to remotely control the LED functions. To change the initial DMX address

press the rotary switch until an arrow appears, then turn to change to the desired DMX starting address. Press to conﬁrm

your selection. Factory setting is 001.

Innovative Lighting Products

Followspot Operating Instructions

V 1.0 4/19/22 8

1092 West Atlanta Street, SE • Suite 600 • Marietta, GA 30060 • 888-252-5912 • [email protected] • cantousa.com

11.3 DIMMER RESOLUTION (8/16B):

The dimming resolution can be controlled at 8 bits from one DMX channel to 16 bits with 2 DMX channels. Factory setting is

8 Bit.

11.4 LOST DMX SIGNAL (DMXMEM):

In case of signal failure this function allows to store in memory the last DMX value. Factory setting is ON. Three options are

available:

11.5 STROBE (STROBE):

This function allows to activate the strobe function. Factory setting is DISABLE.

Innovative Lighting Products

Followspot Operating Instructions

V 1.0 4/19/22 9

1092 West Atlanta Street, SE • Suite 600 • Marietta, GA 30060 • 888-252-5912 • [email protected] • cantousa.com

11.6 STROBE SPEED (SETSTR):

It allows to set the strobe speed. This menu is not active when the strobe function is disabled or when it is remotely controlled

through DMX. Factory setting is OPEN.

11.7 DIMMING CURVE (CURVES):

This function allows to select a response curve for the Astro. A choice of two curves is available: Square and Linear.

Factoring setting is SQUARE.

11.8 CUT OFF DIMMING RESPONSE (CUTOFF):

This function allows to select a LED behavior simulating a tungsten-halogen lamp during the dimming cut off. Factory setting

is SLOW.

Innovative Lighting Products

Followspot Operating Instructions

V 1.0 4/19/22 10

1092 West Atlanta Street, SE • Suite 600 • Marietta, GA 30060 • 888-252-5912 • [email protected] • cantousa.com

11.9 DIMMING BEHAVIOR (SMOOTH):

This function allows to set the LED dimming response. Factory setting is NORMAL.

11.10 FAN SETTING (FAN):

This function allows to set the fan’s response. A choice of three modes is available: Automatic, Silent or Steady. When

fan is in Auto mode, the speed is controlled by the LED temperature. In Silent mode the fan runs slowly to reduce noise. In

Steady mode the fan runs at constant speed, halfway between the minimum and maximum speed. In all cases, if the LED

temperature exceeds the maximum admitted value, the LED is protected by a de-rating security system. Factory setting is

AUTO.

Andere Handbücher für Astro 250

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CANTO USA Scheinwerfer Handbücher

CANTO USA

CANTO USA A10857190 Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

Guangzhou Yinhe Lighting&Sound Equipment Factory

Guangzhou Yinhe Lighting&Sound Equipment Factory NE-204 Bedienungsanleitung

LIVARNO home

LIVARNO home 375304 2101 Originalbetriebsanleitung

Cameo

Cameo CLQS40WW Bedienungsanleitung

Leviton

Leviton Ellipsoid 5/50 Bedienungsanleitung

Monacor

Monacor img Stage Line PARL-56PDX/CR Bedienungsanleitung

Vector

Vector SL3AKV Bedienungsanleitung

Quantum

Quantum Q262 Betriebshandbuch

Philips

Philips Vari-lite VL3015LT Bedienungsanleitung

EUROSPOT

EUROSPOT C51 Bedienungsanleitung

DTS

DTS MINI BRICK ARC Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation VISIBEAM II Handbuch

ACME

ACME LED-MS350B Bedienungsanleitung

EuroLite

EuroLite Akku flat light 1 Bedienungsanleitung

Commercial Electric

Commercial Electric SPTM-1401 Bedienungsanleitung

Vision & Control

Vision & Control SLB-500-W5K7-P-SL Bedienungsanleitung

Teknik

Teknik FLEXI Bedienungsanleitung

Craftsman

Craftsman CMXLSB10 Bedienungsanleitung

EuroLite

EuroLite LED SLS-144 UV Floor Spot Bedienungsanleitung