Caple PH501E Bedienungsanleitung

Contact Caple on 0117 938 7420 or for spare parts www.caple.co.uk

Electric Plinth Heater

instruction manual

PH501E

PH501E Instruction manual.indd 1 16/07/2018 13:44

Instruction manual PH501E

Please keep this instruction manual for future reference

CONTENTS

Safety warnings 3

Environmental Protection 5

Fitting Instructions 6

Operation 10

Troubleshooting 14

Maintenance 15

Technical Data 15

Guarantee 15

PH501E Instruction manual.indd 2 16/07/2018 13:44

Instruction manual PH501E

Please keep this instruction manual for future reference

SAFETY INSTRUCTIONS

Read these instructions carefully and completely

before using your plinth heater, keep it in a

convenient place for reference when necessary

WARNINGS

-This appliance can be used by children aged from 8 years

and above.

-Persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge must be

supervised and given appropriate instruction concerning

the use of the appliance in a safe way and understand

the hazards involved.

-Children shall not play with the appliance.

-Cleaning and user maintenance should not be carried

out by children without supervision.

-Children less than 8 years of age should be kept away

unless continuously supervised.

-The appliance and its accessible parts become hot during

use. Care should be taken to avoid touching heating

elements.

-To prevent ﬁre hazards do not block the ventilation grille

-Keep all ﬂammable materials away from the appliance.

PH501E Instruction manual.indd 3 16/07/2018 13:44

Instruction manual PH501E

Please keep this instruction manual for future reference

WARNINGS

-It is dangerous to alter or modify the speciﬁcations of the

appliance in any way.

-This product is not designed for commercial use, it is a

household appliance only. It is not intended to be used in:

-Staff kitchen areas in shops, ofﬁces and other working

environments.

-Bed and breakfast type environments.

-By clients in hotels, motels and other residential type

environments.

-Ensure that the supply cord is not wedged during the

installation. If the supply cord is damaged, it must

be replaced by a Caple service technician or similarly

qualiﬁed persons in order to prevent a hazard.

-Do not use harsh abrasive cleaners or sharp metal

scrapers to clean the grille, as this may damage or

scratch the surface.

-Ensure the appliance is switched off before any cleaning

or maintenance.

-A Caple approved engineer or highly competent

person(s) should be used for other maintenance

requirements.

PH501E Instruction manual.indd 4 16/07/2018 13:44

Instruction manual PH501E

Please keep this instruction manual for future reference

ENVIRONMENTAL PROTECTION

Waste electrical products should not be disposed of with household waste. Please

recycle where facilities exist. Check with your Local Authority or retailer for recycling

advice. This appliance is marked according to the European directive on Waste

Electrical and Electronic Equipment (WEEE).

By ensuring this product is disposed of correctly, you will help prevent potential

negative consequences for the environment and human health, which could

otherwise be caused by inappropriate waste handling of this product. The symbol

on the product indicates that this product may not be treated as household waste.

Instead it shall be handed over to the applicable collection point for the recycling of

electrical and electronic equipment. Disposal must be carried out in accordance with

local environmental regulations for waste disposal.

For more detailed information about treatment, recovery and recycling of this

product, please contact your local council, your household waste disposal service or

the retailer where you purchased the product.

CE DECLARATIONS OF CONFORMITY

This appliance has been manufactured to the strictest standards and complies

with all applicable legislation, Low Voltage Directive (LVD) and Electromagnetic

Compatibility (EMC).

PH501E Instruction manual.indd 5 16/07/2018 13:44

Instruction manual PH501E

Please keep this instruction manual for future reference

FITTING INSTRUCTIONS

The plinth heater pack contains the following items:

1 x Heater unit

1 x Stainless steel fascia grille with ﬁxing screw pack

1 x Wall controller

1 x Instruction manual

Location

Select a location in a cavity beneath a kitchen cupboard ensuring the area is clean

and level. Care should be taken not to store perishable goods in the cupboard

directly above the heater.

NOTE:

This plinth heater must not be ﬁtted in a bathroom or other high humidity area.

Preparation

This product is normally ﬁtted directly onto the ﬂoor. Once the position has been

decided, mark out and cut the plinth to the dimensions as shown below. Please

take care to make the cut out sizes as accurate as possible as the grill is 100m high.

It is recommended that a gap of 20mm is left between the top of the plinth and the

shelf of the cupboard above to ensure adequate airﬂow

Floor mounting Plinth mounting

A = Width of cut out

B = Height of cut out

A B

360mm 96mm

PH501E Instruction manual.indd 6 16/07/2018 13:44

Instruction manual PH501E

Please keep this instruction manual for future reference

Electrical supply

WARNING:

Ensure the power supply to the socket is

isolated before starting any work.

Electrical connection should be via a double

pole 10 amp fused spur with a minimum

contact gap of 3mm. The fused spur should not

be directly above the heater unit, but should

be accessible after installation. This application

must be earthed.

NOTE:

It is recommended that all electrical work is carried out by a qualiﬁed electrician and

Electrical installation must comply with local and national regulations.

Wall Controller

Installation Instructions

Installation and connection should only be carried out by a suitably qualiﬁed person

and in accordance with the current edition of the IET wiring regulations.

WARNING:

Isolate mains supply before commencing installation.

Choosing a position in the room

The control unit should be ﬁxed to the wall in a position which avoids areas of draft

or direct sunlight. Do not position above or close to other heaters or heat sources.

Also avoid areas which are damp or where the controller can be mechanically

damaged

Wiring box mounting

The controller is designed to ﬁt directly onto a single gang back box. When a metal

box is used this must be earthed. The controller is powered by mains 240VAC 50HZ

and has a power consumption less than 1W. The maximum size of wire that can

be used is 1.5mm¬¬2. Do not overtighten the connector screws. Take care not to

damage the components when connecting the cables.

PH501E Instruction manual.indd 7 16/07/2018 13:44

Instruction manual PH501E

Please keep this instruction manual for future reference

Please ensure that all installations comply with current IER regulations

Commissioning the time switch

Ensure all dust and debris has been cleared away from the work area before

removing the time switch from its packaging.

Fitting the time switch

Connect the mains power supply cables Earth, L and N to the IN connectors Earth

(1), L (2) and N (3)

Connect the heater power cables N, L and Earth to the OUT connectors N (4), L (5)

and Earth (6)

Electrical installation should be carried out by a competent installer in accordance

with the IET wiring regulations (BS.7671) and any relevant local authority bye-laws.

The heater is ﬁtted with a 3 core mains supply cable and should be permanently

connected to the electricity supply via a double pole switch having 3mm gap on

each pole. A switched fuse connection to BS.1363. part 4 is a recommended

mains supply connection accessory to ensure compliance with safety requirements

applicable to ﬁxed wiring installation.

Once the cables are connected, to ﬁt the controller to the back box, remove the

front display unit from the back plate by gently placing the end of a ﬂat head

screwdriver in the 2 slots at the bottom of the controller and twisting gently as

shown in the diagram below.

Fixing holes

PH501E Instruction manual.indd 8 16/07/2018 13:44

Instruction manual PH501E

Please keep this instruction manual for future reference

Gently lift up the end of the facia and unclip from the tabs at the opposite end of

the controller. Do not force the facia off as it could damage the location tabs.

Once the facia is removed you will see the 2 ﬁxing holes to allow the unit to be

screwed onto the back box.

Once back plate has been screwed to the back box place the facia on the location

tabs and close the facia onto the back plate until it locks in place.

General information

Before handing over the installation to the user, always ensure that the system

responds correctly on all control programs and that other electrically operated

equipment and controls are correctly adjusted. Explain how to operate the controls

and hand over the operating instructions to the user.

Safety

- Do not handle the controller with wet hands

- Do not use the controller in rooms where excessive dust is generated or present.

- Ensure all apertures on the controller are kept clear always

- Do not cover the controller

- Do not use the controller if it is damaged

Speciﬁcation

- Supply – 240VAC 50 HZ Temperature Accuracy +/- 1°C

- Maximum load current 10A Temperature display range 5°C - 35°C

- Dimensions 86 x 86 x 14mm Temperature control accuracy ≤1°C

PH501E Instruction manual.indd 9 16/07/2018 13:44

Instruction manual PH501E

Please keep this instruction manual for future reference

Positioning the heater

Once the power supply has been connected ensuring that the electrical cable is not

in contact with any hot surfaces and the plinth is placed in position, slide the heater

unit into the plinth cut out ensuring the power cable is not snagged. Push the unit

fully in until the grill touches the plinth ensuring the heater is centralised in the cut

out and that the unit is sitting ﬂat on the ﬂoor.

Securing the Grill

Once the heater is in the correct position secure the grill to the plinth using the 2

screws provided at point “A”

Grill securing point “A”

OPERATION

- Switch the unit on at the wall socket.

- Select the heat setting (lower switch) to Low “ I “

- Switch the power switch (upper switch) to ON “I”

- If you require more heat move the bottom switch to Boost “ II ”

- To switch off move the power switch to OFF “0”

“0” OFF

“I” ON

“I” Low (950w)

“II” Boost (1900w)

PH501E Instruction manual.indd 10 16/07/2018 13:44

Andere Handbücher für PH501E

Inhaltsverzeichnis

Andere Caple Elektrische Heizung Handbücher

Caple

Caple PH501E Bedienungsanleitung

Beliebte Elektrische Heizung Handbücher anderer Marken

Heatscope

Heatscope PURE Kurzanleitung

Sunbeam

Sunbeam Calentador SFH457A Bedienungsanleitung

Harvia

Harvia K10.5GS Bedienungsanleitung

Harvia

Harvia GL70 Bedienungsanleitung

Heylo

Heylo DE 2 XL Bedienungsanleitung

Heylo

Heylo DE 20 SH Bedienungsanleitung

Harvia

Harvia PP70SP Bedienungsanleitung

Tylo

Tylo SENSE SPORT Bedienungsanleitung

Dirna

Dirna ecodirna SUN Bedienungsanleitung

THERMEx

THERMEx Frame E Wi-Fi Series Bedienungsanleitung

Creda

Creda Heating Solution Bedienungsanleitung

SHUFT

SHUFT UniMAX-R 1400VE EC Bedienungsanleitung

HUUM

HUUM CLIFF Series Bedienungsanleitung

Harvia

Harvia HL70S Bedienungsanleitung

Dimplex

Dimplex DHEBHT Bedienungsanleitung

Radialight

Radialight SIRIO Bedienungsanleitung

Polaris

Polaris PRE E 0715 H Bedienungsanleitung

HeatQ

HeatQ HTL Bedienungsanleitung