Carbide 3D BitRunner V2 Bedienungsanleitung
support@carbide3d.com docs.carbide3d.com 08/19/2021 v1.0
1
BitRunner V2 Quick-Start Guide
The Carbide 3D BitRunner V2 automates your router’s on/off functionality in Carbide Motion. No more
reaching into the work envelope with a moving end mill. Now you can power down your router with the
touch of a button—allowing you to perform tool changes quickly and safely. Use the BitRunner V2 in
conjunction with the BitSetter and BitZero to automate your cutting process even more.
BitRunner V2 comes in deluxe and standard versions. While both versions have the same functionality, the
deluxe version comes with an EMI filter not included in the standard.
Shapeoko Pro, Shapeoko 4, and Shapeoko 3 models that shipped with the Z-Plus as standard equipment are
ready for BitRunner V2 right out of the box. Users with Shapeoko 3 models with Carbide Motion boards 2.3
and earlier (machines purchased before Black Friday 2019) will need to have purchased a new “Carbide
Motion PCB –with Enclosure” at checkout. See Install a New Carbide Motion Board (v2.3 or earlier).
We’re here to help! If you encounter any issues while setting up or using your BitRunner V2, please contact
the Carbide 3D support team at: support@carbide3d.com.
Important Software Information
You must run Carbide Motion 4 or later with the BitRunner V2. Download the most recent version of Carbide
Motion from: carbide3d.com/carbidemotion/download/.
Do Not Connect to Ethernet-Enabled Devices
While an Ethernet cable is used to connect the control pendant to the BitRunner V2, the BitRunner V2 is NOT
an Ethernet device.
WARNING: Do not attempt to connect the BitRunner V2 or control pendant to any Ethernet-enabled
devices such as a modem or internet router.
support@carbide3d.com docs.carbide3d.com 08/19/2021 v1.0
2
Setting Up the BitRunner V2
1.1 Review BitRunner V2 Kit Contents
Item
Description
Qty
Note
A
BitRunner V2 (Deluxe or Standard)
1
BitRunner V2 enclosure and attached power cords
B
Control Pendant
1
Enable/disable the BitRunner V2
C
Logic Cable
1
Connects the BitRunner V2 to the controller
D
Ethernet Cable
1
Connects the BitRunner V2 to the control pendant
E
Grounding Cable
1
Attaches to spindle mount to ground the spindle
Figure 1
support@carbide3d.com docs.carbide3d.com 08/19/2021 v1.0
3
1.2Install a New Carbide Motion Board (v2.3 or earlier)
If you have an older Carbide Motion board (2.3 or earlier), you should have purchased a new Carbide Motion
PCB and enclosure with your BitRunner V2. Before setting up the BitRunner V2, you will need to install the
new controller:
1. Power off the machine.
2. Disconnect the power and USB cables, and all of the motor cables and homing switches from the
board.
3. Remove your old controller from the machine.
4. Install the new controller. The USB and power ports face the back of the machine.
5. Reconnect the motor, homing switch, power, and USB cables.
1.3Connect the BitRunner V2 to the Controller
The BitRunner V2 is designed to lay flat on the ground near your work table and electrical outlet.
The 6-pin male-to-female logic cable connects the BitRunner V2 to the Shapeoko controller. The male end of
the cable plugs into the BitRunner V2 and the female end plugs into the controller.
WARNING: Be careful when plugging in the logic cable. The connectors are polarized and MUST be
inserted properly. While the cable has reverse voltage protection to prevent damage to the
controller and BitRunner V2, the BitRunner V2 will not work unless cable is correctly plugged in.
NOTE: Avoid kinking the cable and ensure it will not be snagged or pinched by any moving parts.
support@carbide3d.com docs.carbide3d.com 08/19/2021 v1.0
4
1.3.1 Connect the Male End to the BitRunner V2
1. Plug the male end of the logic cable into the 6-pin female port on the top of the BitRunner V2. See
Figure 2.
a. The black plastic latch on the side of the connector faces RIGHT.
b. Make sure the connector is fully seated. You will hear the latch click into place.
Figure 2
support@carbide3d.com docs.carbide3d.com 08/19/2021 v1.0
5
1.3.2 Connect the Female End to the Controller
1. Plug the cable’s female end into the 6-pin male BitRunner V2 connector protruding from the front-
end of the controller. See Figure 3.
a. The small triangular peg faces OUT (away from the rail).
b. The connector fits tightly. Press in and down to get it to seat fully.
Figure 3
WARNING: There is a small triangular-shaped peg on one side of the female connector which must
face OUT. The peg is quite small but you will be able to feel it easily with your fingers.
The logic cable has reverse-voltage protection to prevent damage to the controller and BitRunner V2
in the event it is incorrectly plugged in. However, if the cable is plugged in incorrectly, the
BitRunner V2 will not operate.
support@carbide3d.com docs.carbide3d.com 08/19/2021 v1.0
6
1.4Connect the BitRunner V2 to the Control Pendant
Use the flat black Ethernet cable to connect the BitRunner V2 to the control pendant. The two ends of the
cable are interchangeable. See Figure 4.
1. Plug one end of the Ethernet cable into the Ethernet jack on the control pendant.
a. The clear latch and black strain-relief boot face up.
b. Press firmly to fully seat the connector. You will hear the latch click into place.
Figure 4
support@carbide3d.com docs.carbide3d.com 08/19/2021 v1.0
7
2. Plug the other end of the Ethernet cable into the jack on the top of the BitRunner V2. See Figure 5.
a. The clear latch and black strain-relief boot face LEFT.
b. Press firmly to fully seat the connector. You will hear the latch click into place.
1.5Connect the BitRunner V2 to the Router and Power
1. Plug the spindle/router power cord into the short female power cable on the left side of the
BitRunner V2.
2. Plug the longer male power cable into a wall outlet.
Figure 5
support@carbide3d.com docs.carbide3d.com 08/19/2021 v1.0
8
1.6Attach the Grounding Cable to the Spindle Mount (Optional)
To attach the grounding cable:
1. Insert the banana plug into the round port on the top of the BitRunner V2. See Figure 6.
NOTE: We recommend using the included grounding cable to ground the spindle/router in case of
static discharge or electromagnetic interference (EMI). We especially recommend grounding the
spindle during the winter, or in very dry or EMI-noise-heavy environments.
Figure 6
support@carbide3d.com docs.carbide3d.com 08/19/2021 v1.0
9
2. Use an M5 screw to secure the ring terminal end of the grounding cable to one of the two M5 holes
on the left side of the spindle mount. See Figure 7.
3. Use a couple of zip ties to secure the grounding cable. Make sure the cable is secured where it will
not get in the way of the machine’s movements.
1.7Upgrade Carbide Motion
The BitRunner V2 requires at least Carbide Motion 4.
1. Check for the build number in the bottom-left corner of Carbide Motion. Build numbers higher than
400 do not need to be upgraded.
2. If you have an older version, download the most recent version of Carbide Motion from
carbide3d.com/carbidemotion/download and install it to your computer.
Figure 7
support@carbide3d.com docs.carbide3d.com 08/19/2021 v1.0
10
Using the BitRunner V2
2.1 Enable/Disable the BitRunner V2
The BitRunner V2 is enabled and disabled via the control pendant.
To enable the BitRunner V2:
1. Press the control pendant button to supply power to the router. The red button LED will turn ON. See
Figure 8.
To disable the BitRunner V2:
2. Press the control pendant button again to cut power to the router. The button LED will turn OFF.
Figure 8
Inhaltsverzeichnis
Andere Carbide 3D 3D-Drucker Handbücher
