Carel supernode Handbuch
Integrated Control Solutions & Energy Savings
Technical leaet
Foglio istruzioni
supernode
controllo elettronico per umidicazione
electronic controller for humidication
Simboli:
Attenzione: il simbolo nel coperchio plastico del controllo indica di riferirsi al presente foglio
istruzione durante l’installazione elettrica.
Symbol:
Warning: the symbol in the plastic cover of the control, means to refertto this techinical leaet,
during the electrical installation.
3
ENG
+050003325 Supernode for humidification - 1.0 - 20.06.2014
1. INTRODUCTION
The gateway can connect up to a maximum of 20 devices (humiSteam Y-X-W, heaterSteam, gaSteam), allowing up to 150
variables (50 analogue, 50 integer, 50 digital) for each connected device to be managed by the external supervisor.
Seven pre-set templates allow the variables exchanged between the humidier and the gateway to be addressed
automatically, depending on the device selected during programming: simply specify the type of device and the number
of devices connected. The built-in pGD on the Supernode or an external pGD1 terminal can be used for programming.
Supernode part number:
Description Carel P/N
Supernode for humidication + FLSTDmUGWS SNU0000EM0
On the external supervisor side, the protocol can be selected by choosing the corresponding optional serial card. The
possible options are:
item P/N description
1 Modbus®/CAREL RS485 PCOS0004850 Opto-isolated RS485 serial
2 LON PCO10000F0 LON FTT10 serial
3 BACnet™ Ethernet™ PCO1000WB0 Ethernet™ 8 MB serial
4 BACnet™ RS485 PCO1000BA0 BACnet™ MS/TP 485 serial
5 KONNEX PCOS00KXB0 KONNEX BMS port serial
tab. 1a
The module is DIN rail mounted, with 24 Vac power supply (+10%, -15%).
Supernode for humidication allows the possibility to select UR, UEX, UEW, UEY and UG humidiers, including a combination
of dierent models.
For the address settings of the variables on the supervisor side, refer to the dynamic table, requesting from Carel the
“FLSTDmUGWS_Supervisory_List_dinamic_table_supernode_for_humidication” Excel le.
The application on Supernode also features the following options:
• Edit the humidier model, if necessary add/re-address the pre-set variables
• Manage a generic device using the “Universal” model, which can be freely edited according to customer requirements
4
ENG
+050003325 Supernode for humidification - 1.0 - 20.06.2014
2. INSTALLATION
Below is a description of the connectors used for connection and installation of Supernode:
2.1 Connectors
1 5 2
3 4
J7 J10J9J8J5
J1
G
G0
+5Vref
+VDC
ID1
GND
J3
C1
NC1
NO1
J2
SYNC
B1
B2
B3
B4
B5
B6
GND
serial card 2
serial card 1
J4
J6
TLAN
GND
C2
NO2
GND
Y2
Y1
C622P028/R2
GNX
ISOLATED
Tx/Rx PWM 0/10V
GNDTx/Rx
24 V (+10/-15%); 50/60 Hz
48 V (36Vmin…72 Vmax)
input voltage: max. power:
8 VA / 6 W
Key
1 power connector (G+,G0) 24 Vac or 36 V min...72 V max
2 SPDT relay digital output
3 pLAN network connector
4 optically-isolated “Field-Bus” serial connector
5 connector for BMS serial cards
5
ENG
+050003325 Supernode for humidification - 1.0 - 20.06.2014
2.2 Connection diagram
serial card 1
serial card 2
status RS485
GNX RS485+ –
P1 P2 P3
BACnet™MS/TP
G0
G
RS485
CAREL master
GND
RS485
CAREL slave
PCOS004850:
RS485 serial card
PCO100MDM0:
modem card
PCO1000BA0:
BACnet™ MSTP RS485
interface
PCO1000WB0: pCO Web
- Ethernet™/BACnet™
interface card
PCO10000F0:
LON cards
PCO100CLP0:
TREND card
PCOS00KXB0:
Konnex card
device 1
device 2
device n
(n<=20)
6
ENG
+050003325 Supernode for humidification - 1.0 - 20.06.2014
3. PROGRAMMING THE DEVICE
1. Set the number of devices connected to the gateway:
values available: from 1 to 20 devices.
Menu path: Service Service Settings Device settings
2. Set the address and type of device :
Models available: heaterSteam, humiSteam X-plus, humiSteam basic,
gaSteam, generic device
Menu path: Service Service Settings Device settings
The address setting and type of model must be selected for each
device connected to the gateway
3. Set the BMS1 and BMS2 serial port for reading by external
supervisor:
Address, protocol and baud rate setting.
Menu path: Service BMS Settings
4. Set the Carel master protocol for communication between
Supernode and devices:
Supernode communication protocol setting with devices: baud rate
(Retry n. and ORT can be left as default)
Note: the baud rate to be set always corresponds to the slowest
device connected (for heaterSteam the baud rate is 9600).
Menu path: Manufacturer Factory Settings
7
ENG
+050003325 Supernode for humidification - 1.0 - 20.06.2014
5. Edit the model:
The selected model can be edited
Menu path: Manufacturer Devices cong 1-10 or Manufacturer
Devices cong 11-20 (depending on the device)
6. Alarm settings:
Enable alarms in the event of supervisor oine
Menu path: Manufacturer Factory Settings
8
ENG
+050003325 Supernode for humidification - 1.0 - 20.06.2014
Note:
CAREL INDUSTRIES HQs
Via dell’Industria, 11 - 35020 Brugine - Padova (Italy)
Tel. (+39) 049.9716611 - Fax (+39) 049.9716600
Agenzia / Agency:
+050003325 Supernode for humidification - 1.0 - 20.06.2014
Andere Handbücher für supernode
1
Inhaltsverzeichnis
Andere Carel Controller Handbücher
Carel
Carel PZD0SNP0E1 Bedienungsanleitung
Carel
Carel KITCONT101SP Bedienungsanleitung
Carel
Carel pCO1 series Fehlerbehebungshandbuch
Carel
Carel EVD4 Bedienungsanleitung
Carel
Carel EASY COOL Bedienungsanleitung
Carel
Carel pCO2 Series Bedienungsanleitung
Carel
Carel ir33 Universale Leitfaden
Carel
Carel IR32M Bedienungsanleitung
Carel
Carel MasterAria Bedienungsanleitung
Carel
Carel MCHRTF10C0 Bedienungsanleitung
Carel
Carel PJS6 Bedienungsanleitung
Carel
Carel pCO Bedienungsanleitung
Carel
Carel EVD mini Bedienungsanleitung
Carel
Carel uAD Bedienungsanleitung
Carel
Carel pRack pR300T Bedienungsanleitung
Carel
Carel ADP 30 paD Series Bedienungsanleitung
Carel
Carel PJEZ Series Bedienungsanleitung
Carel
Carel uChiller UCHBP00000190 Bedienungsanleitung
Carel
Carel MCHRTF Series Bedienungsanleitung
Carel
Carel PSOPZKEY00/A0 Bedienungsanleitung
