Carrier INDUCTION AIR TERMINALS 36S Bedienungsanleitung

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.

Catalog No. 04-53360009-01 Printed in U.S.A. Form 36S-1SI Pg 1 9-18 Replaces: 36R,S-1SI

Installation Instructions

CONTENTS

GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

VERTICAL UNIT INSTALLATION . . . . . . . . . . . . . . 2

Step 1 — Install Wall Mounting Strip and Hang Base

Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Step 2 — Make Air Connections . . . . . . . . . . . . . . 2

Step 3 — Connect Piping . . . . . . . . . . . . . . . . . . . 3

Step 4 — Install Accessory Grilles (If Supplied,

on Furred-In or Custom

Enclosure Installations) . . . . . . . . . . . . . . . . . . 3

Step 5 — Install Carrier Enclosures . . . . . . . . . . . 3

Step 6 — Install Stiffener Brackets for Enclosure

Runouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Step 7 — Install Enclosure and Runout Arrange-

ment As Required . . . . . . . . . . . . . . . . . . . . . . . . 4

• COLUMN-TO-COLUMN ARRANGEMENT

• COLUMN-TO-COLUMN WITH SHELVING

• ENCLOSURE WITH SINGLE OR DUAL RUNOUT

• SINGLE OR DUAL RUNOUT WITH KICKSTRIP

Step 8 — Balance System . . . . . . . . . . . . . . . . . . 6

HORIZONTAL UNIT INSTALLATION

(Unit-Mounted or Wall-Mounted

Thermostat) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Base Unit Not in Carrier Enclosure . . . . . . . . . . . . 7

Base Unit in Carrier Enclosure . . . . . . . . . . . . . . . 7

Coil Reversal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

GENERAL

These units are controlled by varying water flow through coil.

Follow installation steps in sequence suggested. Each step in-

cludes figure(s) and procedures required for a specific stage

of installation.

Set up a sample installation to familiarize all trades with their

specific job function.

See Fig. 1 for the Proposition 65 warning label. See Fig. 2

and 3 for 36SV,SL base units.

Fig. 1 — Proposition 65 Warning Label

Fig. 2 — 36SV Base Unit

WARNING

AVERTISSEMENT

ADVERTENCIA

This product can expose you to chemicals

including Acrylonitrile, which is known to the

State of California to cause cancer. For

more information, go to

www.P65Warnings.ca.gov

Ce produit peut vous exposer à des

agents chimiques, y compris l’acrylonitrile,

que l’État de Californie reconnaît comme

cancérigènes. Pour plus d’informations,

veuillez consulter

www.P65Warnings.ca.gov

Este producto puede exponerlo a productos

químicos que incluyen acrilonitrilo, que

el estado de California considera que

causa cáncer. Para más información visite

www.P65Warnings.ca.gov

RETURN

SUPPLY

CONDENSATE

PAN

PRIMARY AIR INLET

36S

Induction Air Terminals

(Bypass and Water Control)

Fig. 3 — 36SL Base Unit

VERTICAL UNIT INSTALLATION

Step 1 — Install Wall Mounting Strip and Hang

Base Unit (see Fig. 4)

1. Determine required length of mounting strip. Allow for

length of enclosures and runouts to be used. Maximum

unsupported length of Carrier enclosures is 2-in. on

either side.

2. Locate strip per job prints. Install straight and level using

field-supplied fasteners through alternate and end holes.

Shim if necessary.

3. Install separate mounting strip above base unit strip for

hanging 36SC or 36ST enclosures if used.

4. Mark enclosure vertical center line on wall near mount-

ing strip.

5. Remove base unit from carton. Retain carton and place

over unit after installation to protect from dirt.

6. Remove unit protective packing.

7. Do not remove lint screen clips (taped to condensate pan)

or tee and connector (tape to side of slave unit) until

required.

8. Install two No. 10-24 bolts (factory-supplied) through

two No. 10-24 speed nuts provided. (These, or any other

suitable means, will be used for unit leveling.)

9. Mark base unit vertical center line on unit.

10. Determine from job prints or certified prints relative

position of base unit with respect to enclosure.

11. Hang base unit on wall-mounting strip, using center lines

for reference.

12. Level unit by adjusting two No. 10-24 bolts (or other

means selected).

Fig. 4 — Hanging Base Unit

Step 2 — Make Air Connections (see Fig. 5)

1. Remove end plug from shipping position. Do not discard.

2. Air connections:

Apply sealer (3M Scotch Seal 800 or equivalent) to end

plug and air transition fitting. Install plug and fitting to

plenum connection. Connect duct to transition fitting;

seal connection with duct sealer. CAUTION: Excessive

duct sealer may interfere with damper movement. After

applying sealer, check damper for free travel by rotating

adjusting screw (See Step 8 — Balance System) with

1/8-in. Allen wrench.

3. Check that all tubing connections are tight.

Fig. 5 — End Plug Fittings

Step 3 — Connect Piping (see Fig. 6)

1. If coil requires reversing, see Coil Reversal (page 8).

2. Remove burrs and chips from all joints.

3. Locate piping as shown. Piping may run behind 36S

units.

4. Connect water lines to coil. (Bottom coil connection is

recommended for supply.)

5. Use soft or silver solder, if required, for coil connections.

6. Level condensate pan; straighten strap. If drainable con-

densate pan in used, connect to drain line. Pitch drain

line for adequate flow.

7. Insulate water and drain lines if required. Install service

valves between runouts and water control valves.

8. Compress coil end covers slightly and insert between

coil end flanges, with solid (un-notched) side on forward

coil flange. Install coil end covers on 36SV, 36SD only.

9. Install lint screen against coil, securing to flange with

clips provided. Install 2 lint screens on 36ST.

Fig. 6 — Piping Connections

Step 4 — Install Accessory Grilles (If Supplied,

on Furred-In or Custom Enclosure Installa-

tions) (see Fig. 7)

1. Position recirculation grille mounting frame, using holes

provided. Install recirculation grille panel to grille frame.

2. Install discharge grille frame and removable grille sec-

tions. Field-fabricated collar may be installed on front

and sides of unit discharge if required.

Fig. 7 — Accessory Grilles and Field-Supplied

Collar

Step 5 — Install Carrier Enclosures (see Fig. 8)

1. Remove enclosures from carton.

2. On side-fed enclosures, remove end panel knockout as

required for air connections.

36SC,ST unit enclosures (with kickstrip) are for floor-

fed units only; no knockout is provided.

3. Hang enclosure on wall mounting strip. From job prints

or certified prints, determine relative position of enclo-

sure and base unit. Unit discharge must be in line with

enclosure discharge grille.

Hang 36SC,ST enclosures on separate mounting strip

previously installed above base unit strip.

4. Remove front panel. Fasten enclosure to wall, using clips

or tie-down holes. Re-install panel.

Fig. 8 — Enclosure Installation (36SV Side-Fed

Units)

Step 6 — Install Stiffener Brackets for Enclosure

Runouts (see Fig. 9)

1. Determine length of runout from job prints.

2. Place stiffener brackets on wall mounting strip.

Fig. 9 — Positioning Stiffener Brackets

Step 7 — Install Enclosure and Runout

Arrangement As Required

Use end frame as template when drilling holes on unit enclo-

sure side panels. Tap runout enclosure lightly to ensure tight

fit in end frame slots.

COLUMN-TO-COLUMN ARRANGEMENT (SEE FIG. 10)

1. Drill two 3/16-in. holes for attaching runout.

2. Cut runout enclosure and enclosure panel to desired

length.

3. Fit runout enclosure into slots of one end frame.

4. Insert enclosure panel into end frame slots.

5. Fit second end frame to opposite end of assembly.

6. Hang assembly on wall mounting strip and adjacent to

unit enclosure. Stiffener bracket lip must support bottom

of runout.

7. Attach end frame to unit enclosure with two No. 8 sheet

metal screws (field-supplied).

Fig. 10 — Column-to-Column Enclosure Arrangement

COLUMN-TO-COLUMN WITH SHELVING (SEE FIG. 11)

1. Drill two 3/16-in. holes for attaching runout.

2. Cut runout enclosure, back panel, and shelving to desired

length. Maximum unsupported shelf length is 3 ft.

3. Fit runout enclosure into slots of 2 end frames.

4. Install end panels flush with front of runout enclosure,

leaving space at bottom to insert shelving. Fasten end

panels to runout enclosure with U-clips.

5. Insert shelving below end panels, with flanges turned

down. Shelving rests on lower flange of end frame.

6. Hang assembly on wall mounting strip and adjacent to

unit enclosure. Stiffener bracket lip must support bottom

of runout.

7. Attach end frame to unit enclosure with two No. 8 sheet

metal screws (field-supplied).

ENCLOSURE WITH SINGLE OR DUAL RUNOUT (SEE

FIG. 12)

1. Drill two 3/16-in. holes for attaching runout.

2. Cut runout enclosure to desired length; fit into slots of 2

end frames.

3. Hang assembly on wall mounting strip and adjacent to

base unit enclosure. Stiffener bracket lip must support

bottom of runout.

4. Attach end frame to base unit enclosure with one No. 8

sheet metal screw (field-supplied).

Fig. 11 — Column-to-Column Enclosure with Shelving

Fig. 12 — Enclosure with Single or Dual Runout

Fig. 13 — Single or Dual Runout (with Kickstrip)

SINGLE OR DUAL RUNOUT WITH KICKSTRIP (SEE

FIG. 13)

1. Drill one 3/16-in. hole for attaching runout.

2. Cut runout enclosure and kickstrip to desired length; join

with No. 8 sheet metal screws.

3. Fit runout and kickstrip into slots of 2 end frames.

4. Hang assembly on wall mounting strip and adjacent to

unit enclosure.

5. Attach end frame to unit enclosure with one No. 8 sheet

metal screw (field-supplied).

Step 8 — Balance System (see Fig. 14)

1. Remove construction debris from unit. Remove protec-

tive plastic from thermostat cover.

2. Units are shipped with plenum damper wide open. Turn

damper adjustment screw clockwise to close damper and

decrease nozzle pressure to design value. Two or three

runs may be necessary to obtain proper balance.

Note that 36SL,SM,SC,ST have different nozzle types.

Maximum allowable plenum pressure is 5-in. wg.

Fig. 14 — Pressure Measurements

HORIZONTAL UNIT INSTALLATION

(Unit-Mounted or Wall-Mounted Thermostat)

Base Unit Not in Carrier Enclosure (see Fig. 15)

1. Remove unit from carton. Remove protective packing.

2. Remove Z bars from shipping position. Fasten to unit

with screws and clips provided.

3. Insert short lint screen (91/2-in. height), if used, adjacent

to water coil. Use 2 screws and clips taped to unit front

panel. Install one screw on either side of coil support and

below screen. Install clip through hole as shown.

4. Locate unit per job prints. Suspend as shown.

5. Level unit, using drain pan as reference.

6. Make air connections (see Vertical Unit Installation,

Step 2).

7. Make piping connections (see Vertical Unit Installation,

Step 3, 1 through 7 only).

8. Balance system (see Vertical Unit Installation, Step 8).

Fig. 15 — 36SH Base Unit Installation

Base Unit in Carrier Enclosure (see Fig. 16)

1. Remove base unit, enclosure, and ceiling mounting

plates from their cartons. Remove protective packing.

2. Remove four No. 10-16 x 1/2-in. screws taped to inside of

enclosure end panel.

3. Remove Z bars from shipping position; fasten to unit

with screws and clips provided. Install ceiling mounting

plates to ceiling; lift unit and fasten Z bars to mounting

plates. (Mounting plates may be installed on Z bars and

entire assembly lifted to be secured to ceiling.)

4. Insert short lint screen (91/2-in. height), if used, adjacent

to water coil. Use 2 screws and clips taped to unit front

panel. Install one screw on either side of coil support and

below screen. Install clip through hole as shown.

5. Locate unit per job prints. Suspend as shown.

6. Level unit, using drain pan as reference.

7. Make air connections (see Vertical Unit Installation,

Step 2).

8. Make piping connections (see Vertical Unit Installation,

Step 3, 1 through 7 only).

9. Install long lint screen (111/2-in. height), if used.

10. Lift enclosure so that its flanges pass through slots in

ceiling mounting plate. Slide enclosure flanges over

mounting plate flanges; fasten with 4 screws provided.

11. Balance the system (see Vertical Unit Installation,

Step 8).

Fig. 16 — 36SH Installed in Carrier Enclosure

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.

Catalog No. 04-53360009-01 Printed in U.S.A. Form 36S-1SI Pg 8 9-18 Replaces: 36R,S-1SI

Coil Reversal (see Fig. 17)

Do not reverse coils having vent fittings (except

36SL,SM,SC,ST). To reverse coils without vent fittings:

1. Remove sheet metal screws fastening condensate pan to

coil.

2. Remove sheet metal screws holding coil to unit.

3. Reverse coil end-to-end.

Reverse coil in horizontal plane on 36SL,SM,SC,ST

units.

4. Reassemble coil to unit; re-install condensate pan.

Fig. 17 — Coil Reversal

Andere Handbücher für INDUCTION AIR TERMINALS 36S

Inhaltsverzeichnis

Andere Carrier Steuereinheit Handbücher

Carrier

Carrier SYSTXCC4ZC01 Anleitungen und Rezepte

Carrier

Carrier Touch Pilot Bedienungsanleitung

Carrier

Carrier Infinity SYSTXCCUID01-V Bedienungsanleitung

Carrier

Carrier Infinity SYSTXCCITC01-B Bedienungsanleitung

Carrier

Carrier 30GTN Bedienungsanleitung

Carrier

Carrier LonWorks i-Vu Link Kurzanleitung zur Einrichtung

Carrier

Carrier 7C-CM-C1K-XA Bedienungsanleitung

Carrier

Carrier Infinity SYSTXCCSAM01 Bedienungsanleitung

Carrier

Carrier B Series Bedienungsanleitung

Carrier

Carrier AquaSnap 30WG Series Bedienungsanleitung

Carrier

Carrier Infinity series Bedienungsanleitung

Carrier

Carrier 61AF Bedienungsanleitung

Carrier

Carrier Kilsen KAL740 Montageanleitung

Carrier

Carrier INFINITY SYSTXCCITC01 Bedienungsanleitung

Carrier

Carrier 80AWX-065 series Handbuch

Carrier

Carrier AppController OPN-APP Installationshandbuch

Carrier

Carrier 42BJ ICM Bedienungsanleitung

Carrier

Carrier 50CJ Handbuch

Carrier

Carrier 50CJ Handbuch

Carrier

Carrier 30MP015-045 Bedienungsanleitung

Carrier

Carrier 50CO Series Handbuch

Carrier

Carrier WTC-LEX Bedienungsanleitung

Carrier

Carrier 42BJ MCI LEC Bedienungsanleitung

Carrier

Carrier Signature Series Montageanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung