Carrier 38YCC Series Bedienungsanleitung

Product

Data

38YCC 50 Hz

Heat Pump

Sizes 024 thru 060

The 38YCC 50 Hertz Outdoor

Sections of Split-System Heat Pumps

aredesignedforquiet, reliableheating

during the winter and cooling during

the summer. With an EER up to 9.2,

these heat pump systems provide

economy of operation through energy

conservation when used with

components designated by Carrier.

They recover heat for indoor comfort

from outdoor air during the heating

season and, by automatically

reversing the refrigerant system,

remove indoor heat and excess

humidity during the cooling season.

FEATURES/BENEFITS

ElectricalRange

— Unitsareoffered

in single phase 230v 50 Hz. Three-

phase units are available in sizes 036,

048, and 060 in 400v 50 Hz.

Size Range

— The 38YCC is

available in nominal sizes 024, 036,

048 and 060 to meet the needs of

residential and light commercial

applications.

Compressor

— Designed

specifically for heat pump duty, with

energy efficiency during heating and

cooling operation. The compressor is

hermetically sealed against

contamination to assure long life and

dependable performance, internally

sprung (units with reciprocating

compressor) and externally mounted

onrubberisolatorsforquietoperation.

Continuous compressor operation is

approved down to –30

F (–34.4

in the heating mode, and down to

F (12.8

C) in the cooling mode.

(See heating and cooling performance

tables.)

Built-in-Reliable Components

—

Include a suction-tube accumulator

that reduces the amount of liquid

refrigerant that reaches the

compressor; low-pressure switch to

stop the compressor if refrigerant

charge is lost; crankcase heater on

units with reciprocating compressor

and all 3-phase units to keep

compressor oil warm and free of

refrigerant for maximum lubricity;

internal compressor relief valve for

high-pressure protection.

DischargeSilencer

— Minimizes low

frequency sound and pressure

pulsation generated by compressor

discharge gas.

Defrost Control Board

—

Incorporates a defrost relay, defrost

timer, and low-voltage terminations.

The defrost control is a time and

temperature initiation/termination

control which includes 3 field-

selectable time periods of 30, 50, and

90 minutes. The control includes built-

in 5-minute compressor delay for units

equipped with scroll compressors.

Weather-ProtectiveCabinet

—Steel

is protected with a heavy galvanized

coating and treated with a layer of zinc

phosphate. A coat of modified

polyester powder coating is then

applied and baked-on, providing each

unitwith ahard, smoothfinish thatwill

last for many years.

All screws on cabinet exterior are

coated for a long-lasting rust-resistant,

quality appearance.

Unit Design

— All units are equipped

with totally enclosed fan motors for

greater reliability under rain and snow

conditions. The large, wraparound coil

uses copper tube and enhanced

aluminum fin and is designed for

optimum heat transfer during heating

and cooling. Vertical air discharge

carriessound andairup andawayfrom

adjacent patio areas and foliage. Coils

can be cleaned with a common garden

hose.

External Service Valves

— Both

service valves are brass, front seating

type. Valves are externally located

so refrigerant tube connections can

be made quickly and easily. Each

valve has a service port for ease of

checking operating refrigerant

pressures. The 38YCC has sweat-type

field connections.

Safety

— All units are designed and

manufactured in accordance with

UnderwritersLaboratories(U.L.1995)

standard for safety, heating and

cooling equipment.

Model number nomenclature

38YCC 024

Electric Heat Pump

Nominal Capacity

024 — 24,000 Btuh (7.0 Kw) 048 — 48,000 Btuh (14.1 Kw)

036 — 36,000 Btuh (10.6 Kw) 060 — 60,000 Btuh (17.6 Kw)

703

Packaging

Series

Electrical

7 — 230-1-50

9 — 400-3-50

Quality Assurance

Physical data

* Tube sizes are for lengths up to 50 ft (15.24m). For lengths over 50 ft (15.24m), consult Residential Split System Long-Line Application Guideline.

NOTE:

See unit Installation Instructions for proper installation.

METERING DEVICE

*Piston listed is for any approved coil combination.

UNIT SIZE-SERIES 024-70 036-70, 90 048-70, 90, 92 060-90, 92

OPERATING WT (Lb/Kg)

140 / 63.6 216 / 97.8 216, 216, 224 / 97.8, 97.8, 101.8 257, 259 / 116.4, 117.5

COMPRESSOR

Manufacturer

Type

Copeland

Recip Copeland

Recip Millennium, Millennium, Copeland

Scroll Millennium, Copeland

Scroll

REFRIGERANT

Control

Charge (Lb/Kg) @ 15 ft (4.57m)

R-22

Piston

4.84 / 2.20 7.93 / 3.60 5.32, 5.32, 7.25 / 2.41, 2.41, 3.29 10.95, 10.75 / 4.97, 4.88

CONDENSER FAN

Propeller Type, Direct Drive

Air Discharge

Vertical

Air Qty (CFM / L/S)

2160 / 1019 2750 / 1298 2750 / 1298 2750 / 1298

Motor HP

1/10 1/4 1/4 1/4

Motor RPM (50 Hz)

850 900 900 900

CONDENSER COIL

Face Area (Sq ft/m

)

12.4 / 1.15 22.4 / 2.08 18.7 / 1.74 18.7 / 1.74

Fins per In. / Fins per Cm

20 / 8 20 / 8 20 / 8 20 / 8

Rows

1112

Circuits

2346

CONNECTION (In./mm ID)

Vapor

Liquid

Sweat

5/8 / 15.875 3/4 / 19.05 7/8 / 22.225 7/8 / 22.225

3/8 / 9.525

REFRIG TUBES* (In./mm OD)

Vapor (0–50 Ft (15.24m)

Tube Length)

5/8 / 15.875 3/4 / 19.05 7/8 / 22.225 1-1/8 / 28.575

Vapor (Max Diameter for

Long-Line Applications)

3/4 / 19.05 7/8 / 22.225 1-1/18 / 28.575

Liquid (0–50 Ft (15.24m) Tube

Tube Length)

3/8 / 9.525

Liquid (For Long-Line

Applications)

3/8 / 9.525

UNIT

SIZE-SERIES OUTDOOR

PISTON INDOOR

PISTON*

024-70

49 63

036-70, 90

61 73

048-70, 90

73 88

048-92

73 90

060-90

76 98

060-92

76 96

Accessories

* Isolation relay required.

† Consult low-ambient controller Installation Instructions for application.

‡ Hard shutoff TXV requires compressor start assist on reciprocating compressors.

N/A — Not applicable in this application.

ORDERING NUMBER DESCRIPTION

KAATD0101TDR

Time-Delay Relay — All Sizes

P251-0083 (RCD)*

Low-Ambient Controller — All Sizes

P504-8083S (RCD)

Filter Drier — Bi-Flow — Sizes 024, 036

P504-8163S (RCD)

Filter Drier — Bi-Flow —

Sizes 048, 060

32LT660004 (RCD)

MotorMaster® Control — Sizes 024 (70), 036 (70), 048 (70)

32LT660005 (RCD)

MotorMaster® Control — Sizes 036 (90), 048 (90, 92), 060 (90, 92)

KAAFT0101AAA

† Evaporator Freeze Thermostat — All Sizes

KAAWS0101AAA

Winter Start Control — All Sizes

KHAIR0101AAA

† Isolation Relay — All Sizes

KSACY0101AAA

Cycle Protector — All Sizes

KSAHS1001AAA

Start Assist — Capacitor and Relay — Size 024 (70)

KSAHS1301AAA

Start Assist — Capacitor and Relay — Size 036 (70)

KSAHS1601AAA

Start Assist — Capacitor and Relay — Size 048 (70)

N/A

Start Assist — Capacitor and Relay — Sizes 036 (90), 048 (90, 92), 060 (90, 92)

KAACS0201PTC

Start Assist — PTC — Sizes 024 (70), 036 (70), 048 (70)

N/A

Start Assist — PTC — Sizes 036 (90), 048 (90, 92), and 060 (90, 92)

KSASH1101COP

Sound Hood — Sizes 024, 036

KSASH2001CYL

Sound Hood — Sizes 048, 060

KHAOT0301FST

Outdoor Thermostat — All Sizes

KHAOT0201SEC

Secondary Outdoor Thermostat — All Sizes

KHAIC0101AAA

Interface Control (Optimizer II®) — All Sizes

KSATX0601HSO‡

TXV (Hard Shutoff) — Sizes 024, 036

KSATX0701HSO‡

TXV (Hard Shutoff) — Sizes 048, 060

KHATX0301RPB

TXV (RPB) — Size 024

KHATX0501RPB

TXV (RPB) — Sizes 036

KHATX0601RPB

TXV (RPB) — Size 048

KHATX0701RPB

TXV (RPB) — Size 060

KHAHI0101HPS

High-Pressure Switch — All Sizes

KHALS0101LLS

Liquid-Line Solenoid Valve (LSV) — All Sizes

P165-0001 (RCD)

Unit Risers — All Sizes (2 Required/Unit)

THERMOSTAT DESCRIPTION

TSTATCCNHP01-A

Thermostat, Auto Changeover, Non-Programmable,

C, 2-Stage Heat, 1-Stage Cool

TSTATCCPHP01-A

Thermostat, Auto Changeover, 7-Day Programmable,

C, 2-Stage Heat, 1-Stage Cool

TSTATCCPDF01-A

Thermostat Auto Changeover, 7-Day Programmable,

C, Dual Fuel Thermostat

Must be used with Outdoor Sensor (TSTATCCSEN01)

--HH--07AT-215

Thermostat, Manual Changeover, Non-Programmable,

F, 2-Stage Heat, 1-Stage Cool

TSTATCCSEN01

Outdoor Air Temperature Sensor

TSTATXXNBP01

Backplate for Non-Programmable Thermostat

TSTATXXPBP01

Backplate for Programmable Thermostat

TSTATXXCNV10

Thermostat Conversion Kit (4 to 5 wire) — 10 Pack

Accessory usage guideline

* For tubing line sets between 50 and 175 ft (15.24 and 53.34m), refer to Residential Split-System Long-Line Application Guideline.

† For buried line applications, refer to Residential Split System Buried Line Application Guideline.

‡ Only when low-pressure switch is used.

Accessory description and usage (Listed alphabetically)

1. Compressor Start Assist — Capacitor and Relay

Start capacitor and start relay gives “hard” boost to compressor motor at each start-up.

SUGGESTED USE: Installations where interconnecting tube length exceeds 50 ft (15.24m).

Installations where outdoor design temperature exceeds 105

F (40.6

C).

Replacement installations with hard shutoff expansion valve on indoor coil.

Installations where Liquid-Line Solenoid Valve has been added.

Units installed with Low-Ambient Controller.

2. Compressor Start Assist — PTC

Solid-state electrical device which gives a “soft” boost to compressor motor at each start-up.

SUGGESTED USE: Installations with marginal power supply.

Replacement installations with rapid pressure balance (RPB) expansion valve on indoor coil.

3. Cycle Protector

Solid-state timing device which prevents compressor rapid recycling. Control provides an approximate 5-minute delay after power to the compressor

has been interrupted for any reason, including normal room thermostat cycling.

SUGGESTED USE: Installations in areas where power interruptions are frequent.

Where user is likely to “play” with room thermostat.

All commercial installations.

Installations where interconnecting tube length exceeds 50 ft (15.24m).

High-rise applications.

4. Evaporator Freeze Thermostat

An SPST temperature actuated switch which stops unit operation when evaporator reaches freeze-up conditions.

SUGGESTED USE: All units where Winter Start Control has been added.

All units where Low-Ambient Controller has been added.

5. Filter Drier—Bi-Flow

A device for removing contaminants from refrigerant circulating in a heat pump system: 2-direction flow.

SUGGESTED USE: All split-system heat pumps.

6. High-Pressure Switch

Auto reset SPST switch activated by refrigerant pressure on high side of refrigerant circuit. Cycles compressor off if refrigerant pressure rises to about

426

7 psig and resets at 320

20 psig. Provides protection against compressor damage due to loss of outdoor airflow. To prevent rapid compressor

recycling, Cycle Protector can be used with this switch.

SUGGESTED USE: Installations exposed to very “dirty” outdoor air.

Installations where condenser inlet air temperature exceeds 125

F (51.7

C).

7. Interface Control (Optimizer II®)

An electric control for controlling a heat pump and gas or oil furnace system for maximum energy savings. It allows heat pump to operate down to a

predetermined economic balance point temperature, then switches to allow furnace operation only below that temperature. Requires outdoor thermostat

to be adjusted for economic balance point temperature.

SUGGESTED USE: All heat pump and gas- or oil-fired furnace combination systems.

8. Isolation Relay

An SPDT relay which switches the Low-Ambient Controller out of the outdoor fan motor circuit when heat pump switches to heating mode.

SUGGESTED USE: All heat pumps where Low-Ambient Controller has been added.

9. Liquid-Line Solenoid Valve (LSV)

An electrically operated shutoff valve to be installed at the outdoor unit and which stops and starts refrigerant liquid flow in response to compressor

operation. Maintains a column of refrigerant liquid ready for action at next compressor operation cycle.

NOTE:

Compressor Start Assist–Capacitor and Relay must also be used.

SUGGESTED USE: In certain long-line applications. Refer to Residential Split System Long-Line Application Guideline.

ACCESSORY

REQUIRED FOR

LOW-AMBIENT

APPLICATIONS

(Below 55

F/12.8

REQUIRED FOR

LONG-LINE

APPLICATIONS*

(Over 50 Ft/15.24m)

REQUIRED FOR

BURIED LINE

APPLICATIONS†

(Over 3 Ft/0.914m)

Crankcase Heater

Yes Yes Yes

Evaporator FreezeThermostat

Yes No No

Winter Start Control

Yes‡ No No

Accumulator

No No Yes

Compressor Start Assist

Capacitor and Relay

Yes Yes Yes

Low Ambient Controller

MotorMaster® Control

Yes No No

Wind Bafﬂe

See Low-Ambient Instructions No No

Support Feet

Recommended No No

Liquid-Line SolenoidValve

Hard ShutoffTXV No See Long-Line

Application

Guideline Yes

Accessory description and usage (Listed alphabetically) continued

10. Low-Ambient Controller

Head pressure controller is a cycle control device activated by a temperature sensor mounted on a header tube of the outdoor coil. It is designed to cycle

the outdoor fan motor in order to maintain condensing temperature within normal operating limits (approximately 100°F (37.8°C) high and 60°F

(15.6°C) low). The control will maintain working head pressure at low-ambient temperatures down to 0°F (–17.8°C) when property installed.

SUGGESTED USE: Cooling operation at outdoor temperatures below 55°F (12.8°C).

11. MotorMaster® Control

A fan speed control device activated by a temperature sensor. Designed to control condenser fan motor speed in response to the saturated, condensing

temperature during operation in cooling mode only. For outdoor temperatures down to –20°F (–28.9°C), it maintains condensing temperature at

100°F ±10°F (37.8°C ±5.5°C).

SUGGESTED USE: Cooling operation at outdoor temperatures below 55°F (12.8°C).

All commercial installations.

12. Outdoor Air Temperature Sensor

A device that allows the temperature at a remote location (outdoors) to be displayed at the thermostat.

SUGGESTED USE: All corporate programmable thermostats.

13. Outdoor Thermostat

An SPDT temperature actuated switch which turns on supplemental electric heaters when outdoor air temperature drops below set point.

SUGGESTED USE: Heat pump installations with multiple-stage supplemental heaters

14. Secondary Outdoor Thermostat

An SPDT temperature actuated switch which turns on a third stage of supplemental electric heaters when outdoor air temperature drops below the

second-stage set point.

SUGGESTED USE: Heat pump installations where 3-stage operation of supplemental heaters is desired.

15. Sound Hood

Wraparound sound attenuation cover for the compressor. Reduces the sound level by about 2 dBA.

SUGGESTED USE: Unit installed closer than 15 ft (4.55m) to quiet areas—bedrooms, etc.

Unit installed between 2 houses less than 10 ft (3.04m) apart.

16. Thermostatic Expansion Valve (TXV) — Bi-Flow

A modulating flow-control valve which meters refrigerant liquid flow rate into the evaporator in response to the superheat of the refrigerant gas leaving

the evaporator. Kit includes valve, adapter tubes, and external equalizer tube. Both hard shutoff and RPB valves are available.

SUGGESTED USE: For improved system performance in cooling mode for certain combinations of indoor and outdoor units. Refer to ARI Unitary Directory.

Required for use on all zoning systems.

17. Time-Delay Relay

An SPST delay relay which briefly continues operation of the indoor blower motor to provide additional cooling after the compressor cycles off.

SUGGESTED USE: For improved efficiency ratings for certain combinations of indoor and outdoor units. Refer to ARI Unitary Directory.

18. Unit Risers

Six-in. tall plastic rails that are used to elevate outdoor units above mounting pad. The risers are adjustable from 24- to 34-in. long..

SUGGESTED USE: Heat pump installations in light to moderate snowfall areas.

Coastal installations.

Windy areas where debris can circulate.

Rooftop installations.

19. Winter Start Control

An SPST delay relay which bypasses the low-pressure switch for approximately 3 minutes to permit start-up for cooling operation under low-load

conditions.

SUGGESTED USE: All heat pumps where Low-Ambient Controller has been added.

Electrical data

* Permissible limits of the voltage range at which unit will operate satisfactorily. Operation outside these limits may result in unit failure.

† Time-delay fuse.

‡ Length shown is as measured 1 way along the wire path between the unit and the service panel for voltage drop not to exceed 2%.

** If wire is applied at ambient greater than 30°C (86°F), consult Table 310-16 of the NEC (ANSI/NFPA 70). The ampacity of nonmetallic-sheathed-

cable (NM), trade name ROMEX, shall be that of 60°C (140°F) conductors, per the NEC (ANSI/NFPA 70) Article 336-30.

If other than uncoated (non-plated), 60°or 75°C (140°or 167°F) insulation, copper wire (solid wire for 10 AWG and smaller, stranded wire for

larger than 10 AWG) is used, consult applicable tables of the NEC (ANSI/NFPA 70).

FLA — Full Load Amps

HACR — Heating, Air Conditioning, Refrigeration

LRA — Locked Rotor Amps

MCA — Minimum Circuit Amps

RLA — Rated Load Amps

NOTE: Control circuit is 24v on all units and requires external power source. Copper wire must be used from disconnect to unit. All motors/compres-

sors contain internal overload protection.

OUTDOOR

UNIT V/PH OPER VOLTS* COMPRESSOR FAN

FLA MCA

MIN WIRE

SIZE**

60°C/75°C

MAX

LENGTH

(Ft)‡

60°C/75°C

MAX

LENGTH

(m)‡

60°C/75°C

MAX FUSE†

OR HACR

TYPE CKT

BKR AMPSMax Min LRA RLA

024-70 230-1 253 207 68.0 11.5 1.4 15.8 14/14 55/39 16.7/11.9 25

036-70 94.0 16.5 1.6 22.2 12/12 65/47 19.8/14.3 35

048-70 140.0 19.2 1.6 25.6 10/10 96/70 29.3/21.3 40

036-90

400-3 440 360

42.0 6.4 0.7 8.7 14/14 260/247 79.2/75.3 15

048-90 66.5 8.0 0.7 10.7 14/14 165/157 50.3/47.9 15

048-92 63.0 7.9 0.7 10.7 14/14 165/157 50.3/47.9 15

060-90 73.0 9.5 0.7 12.6 14/14 165/157 50.3/47.9 20

060-92 74.0 9.0 0.7 11.9 14/14 165/157 50.3/47.9 20

AIR DISCHARGE

AIR IN

ASQ

9.5mm DIA

TIEDOWN

KNOCKOUTS

(2) PLACES

73.0mm

31.8mm

FIELD CONTROL SUPPLY 

CONN 22.2mm DIA 

HOLE

FIELD POWER SUPPLY CONN

22.2mm DIA HOLE WITH 

28.6mm DIA KNOCKOUT 

AND 34.9mm DIA 

KNOCKOUT

9.5mm DIA LIQUID 

LINE CONN

D DIA VAPOR LINE CONN

AIR IN

AIR DISCHARGE

AIR IN AIR IN

AIR DISCHARGE

NOTES:

1. Allow 762.0 mm clearance to service side of unit,

1219.2 mm above unit, 152.4 mm on one side,



304.8 mm on remaining side, and 

609.6 mm between units for proper airflow.

2. Minimum outdoor operating ambient in cooling mode is 13°C 

(unless low ambient control is used) max. 52°C.

3. Maximum outdoor operating ambient in heating mode

is 19°C.

4. Series designation is the 13th position of the unit model number.

5. Center of gravity .

Dimensions (S.I.)

DIMENSIONS (mm)

UNIT

SIZE SERIES ABCDEFGHJKLMNP

MINIMUM MOUNTING

PAD DIMENSIONS

024 70 571.5 862.0 81.0 15.9 93.6 460.4 501.7 549.3 365.1 479.4 560.4 317.5 304.8 355.6 571.5 x 571.5

036 70, 90 762.0 1014.4 82.6 19.1 165.1 596.9 692.2 739.8 508.0 669.9 750.9 381.0 400.1 393.7 762.0 x 762.0

048 70, 90 762.0 862.0 82.6 22.2 165.1 596.9 692.2 739.8 508.0 669.9 750.9 381.0 400.1 393.7 762.0 x 762.0

048 92 762.0 862.0 82.6 22.2 165.1 596.9 692.2 739.8 508.0 669.9 750.9 387.4 396.9 393.7 762.0 x 762.0

060 90 762.0 862.0 82.6 22.2 165.1 596.9 692.2 739.8 508.0 669.9 750.9 400.1 396.9 381.0 762.0 x 762.0

060 92 762.0 862.0 82.6 22.2 165.1 596.9 692.2 739.8 508.0 669.9 750.9 396.9 400.1 384.2 762.0 x 762.0

A97281

Dimensions (English)

A97045

AIR DISCHARGE

AIR IN

ASQ

3/8 -IN. DIA

TIEDOWN

KNOCKOUTS

(2) PLACES

27/8″

11/4″

FIELD CONTROL SUPPLY 

CONN 7/8 -IN. DIA 

HOLE

FIELD POWER SUPPLY CONN

7/8 -IN. DIA HOLE WITH 

1 1/8 -IN. DIA KNOCKOUT 

AND 1 3/8 -IN. DIA 

KNOCKOUT

3/8 -IN. DIA LIQUID 

LINE CONN

D DIA VAPOR LINE CONN

AIR IN

AIR DISCHARGE

AIR IN AIR IN

AIR DISCHARGE

NOTES:

1. Allow 30 in. clearance to service side of

unit, 48 in. above unit, 6 in. on one side, 12 in.



on remaining side, and 24 in. between units for proper airflow.

2. Minimum outdoor operating ambient in cooling mode is

55°F (unless low ambient control is used) max. 125°F.

3. Maximum outdoor operating ambient in heating mode

is 66°F.

4. Series designation is the 13th position of the unit

model number.

5. Center of gravity .

DIMENSIONS (IN.)

UNIT

SIZE SERIES ABCDEFGHJKLMNP

MINIMUM MOUNTING

PAD DIMENSIONS

024 70 22-1/2 33-15/16 3-3/16 5/8 3-11/16 18-1/8 19-3/4 21-5/8 14-3/8 18-7/8 22-1/16 12-1/2 12 14 22-1/2 x 22-1/2

036 70, 90 30 39-15/16 3-1/4 3/4 6-1/2 23-1/2 27-1/4 29-1/8 20 26-3/8 29-9/16 15 15-3/4 15-1/2 30 x 30

048 70, 90 30 33-15/16 3-1/4 7/8 6-1/2 23-1/2 27-1/4 29-1/8 20 26-3/8 29-9/16 15 15-3/4 15-1/2 30 x 30

048 92 30 33-15/16 3-1/4 7/8 6-1/2 23-1/2 27-1/4 29-1/8 20 26-3/8 29-9/16 15-1/4 15-5/8 15-1/2 30 x 30

060 90 30 33-15/16 3-1/4 7/8 6-1/2 23-1/2 27-1/4 29-1/8 20 26-3/8 29-9/16 15-3/4 15-5/8 15 30 x 30

060 92 30 33-15/16 3-1/4 7/8 6-1/2 23-1/2 27-1/4 29-1/8 20 26-3/8 29-9/16 15-5/8 15-3/4 15-1/8 30 x 30

38YCC BALANCE POINT WORKSHEET

BUILDING HEAT LOSS, KW

UNIT INTEGRATED HEATING CAPACITY, KW

Printed in U.S.A. 11-94

OUTDOOR TEMPERATURE, °C

-20 -10 010 20

BASED ON INDOOR ENT. AIR AT 21°C

AND AT RATED CFM

38YCC024

FB4AS024

38YCC036

FB4AS036

38YCC048

FB4AS048

38YCC060

FB4AS060

A97280

Andere Handbücher für 38YCC Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Carrier Wärmepumpe Handbücher

Carrier

Carrier 48JZ024 Bedienungsanleitung

Carrier

Carrier AQUAZONE 50HQP072-120 Kurzanleitung

Carrier

Carrier 38YY...G Bedienungsanleitung

Carrier

Carrier AQUAZONE 50PSH Abmessungen und Installationsanleitung

Carrier

Carrier 50HQ Abmessungen und Installationsanleitung

Carrier

Carrier 50NQ Abmessungen und Installationsanleitung

Carrier

Carrier AIR COOLED SPLIT SYSTEM 38AQS008 Bedienungsanleitung

Carrier

Carrier AquaSnap 30AWH-R Bedienungsanleitung

Carrier

Carrier AquaSnap 61AF-A Handbuch

Carrier

Carrier 25HPA6 Kurzanleitung

Carrier

Carrier 38YH Bedienungsanleitung

Carrier

Carrier 38BYG Series Bedienungsanleitung

Carrier

Carrier Infinity 24VNA6 Bedienungsanleitung

Carrier

Carrier bryant 607E K Series Bedienungsanleitung

Carrier

Carrier Infinity 50DT Bedienungsanleitung

Carrier

Carrier 38AYC Series Bedienungsanleitung

Carrier

Carrier 51QC Bedienungsanleitung

Carrier

Carrier 38MBRC Series Bedienungsanleitung

Carrier

Carrier CPCRKHTR003A00 Bedienungsanleitung

Carrier

Carrier 50FF 020-093 Handbuch

Carrier

Carrier Performance 50VR-K Bedienungsanleitung

Carrier

Carrier 38AUQ Abmessungen und Installationsanleitung

Carrier

Carrier 38AQ012 Abmessungen und Installationsanleitung

Carrier

Carrier 50TJQ004-007 Abmessungen und Installationsanleitung

Beliebte Wärmepumpe Handbücher anderer Marken

MICROWELL

MICROWELL HP 1000 GREEN Bedienungsanleitung

Sanyo

Sanyo SAP120FCH Bedienungsanleitung

Daikin

Daikin EHYHBH05AA Bedienungsanleitung

Panasonic

Panasonic WH-SDF03E3E5 Leitfaden

Bryant

Bryant 544B Bedienungsanleitung

Airxcel

Airxcel 45000 Series Handbuch

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Bedienungsanleitung

Dimplex

Dimplex LI 16I-TUR Benutzerhandbuch

TGM

TGM CTV14CN018A Bedienungsanleitung

Kokido

Kokido K2O K880BX/EU Fehlerbehebungshandbuch

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Kurzanleitung

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Betriebsanleitung

Ariston

Ariston NIMBUS Bedienungsanleitung

Weishaupt

Weishaupt WWP L 7 Benutzerhandbuch

GE Zoneline AZ85H09EAC Bedienungsanleitung

Bryant

Bryant Preferred Series Bedienungsanleitung

Daikin

Daikin altherma EJHA04AAV3 Bedienungsanleitung

Bryant

Bryant 549B Series Abmessungen und Installationsanleitung