Carson IS-200 Bedienungsanleitung

IS-200

HookUpzTM 2.0

Smartphone Optic Adapter

Congratulations on selecting your new HookUpz Smartphone Optic Adapter! In order to

achieve optimum performance, please follow instructions for proper use and care.

SMARTPHONE OPTIC ADAPTER DIAGRAM

FOR OPTIC: FOR PHONE:

•see

Frequently Asked Questions,

on page 10.

Alignment

Screw

Left

Clamp

Right

Clamp

PRODUCT SPECIFICATION:

Weight:

0.3 lbs

Dimensions:

4.3” x 2.3” x 4.5”

INSERTING PHONE:

1. Rotate to unlock top clamp. 2. Slide top clamp into

uppermost position. 3. Insert phone into left clamp.

4. Squeeze and pull right clamp

past edge of phone.

Fig. 1

Fig. 4

5. Release right clamp to secure

phone. 6.Ensure phone is flat as

possible to adapter.

Fig. 2 Fig. 3

Fig. 5

Fig. 6

CARSON®

ALIGN AND LOCK:

1. Slide phone vertically until the primary camera* is

roughly aligned with camera cutout.

Fig. 7

*Multiple-Lens Camera Phones:

If there is more than one rear facing camera,

use the primary one.Typically, the primary is a

1x wide-angle color camera, and the other

camera(s) are secondary.

For the latest instructions on multiple camera

phones, please visit: www.carson.com/multicam

2.Turn alignment screw until

camera is centered in camera

cutout.

3. Slide top clamp down against

phone edge.

Fig. 8

Fig. 9

4.While holding top clamp tight

to phone, rotate to lock. 5. Figure 11 shows a properly

aligned camera.If needed,

use alignment screw and top

clamp to make further

adjustments.

Fig. 11

Fig. 10

BEFORE ATTACHING TO OPTIC:

Make sure optic is focused. If your optic has flexible

eyecups, fold down and attach optic.

Fig. 12

ATTACHING TO OPTIC:

1. Squeeze arms to open optic clamp.

Fig. 13

2. Do not squeeze arms while

reaching around phone, otherwise

phone alignment may be altered.

3. Once opened, place over

eyepiece and release.

4. Phone can be positioned in either

portrait or landscape.

Fig. 16

5. Ensure adapter is flush to the

eyepiece of your optic. 6. For smaller eyepieces, push optic

lock down while attached to

eyepiece.

Note:This is not needed for

larger eyepieces.

7.Turn on camera. If image is not

centered, repeat alignment steps.

Fig. 19

Fig. 14

Fig. 15

Fig. 17

Phone. 18

LOCK

8.To maximize your image, pinch to

enlarge image.For best results, use

in video mode.

TO REMOVE OPTIC FROM ADAPTER:

Press optic clamp arms together to open

adapter and remove from optic.To minimize

an audible click noise, or if the optic lock doe

not release automatically, rotate it upwards to

unlock.

TO REMOVE PHONE FROM ADAPTER:

To save your alignment, make no further

adjustments to the top clamp and alignment

knob. Simply remove phone using right clam

only as shown in Fig.4.

USING ADAPTER AGAIN:

The alignment of your phone to the adapter

should be saved from the initial setup, so

many steps can be skipped (Fig.1-2, 7-10)

and only a quick fine adjustment of the

alignment may be needed.

Fig. 20

Squeeze

open

optic

clamps

and

insert

lens

spacer

between

clamps.

Snap

lens

spacer

into

place

FREQUENTLY ASKED QUESTIONS:

Q1: I am trying to enlarge the image on my phone but its still a

small circle, what can I do?

A1: To maximize your image, select video mode and/or pinch your

phone screen to digitally zoom.Depending on the combination of

your phone and optic, you may need to use the included lens

spacer. Insert and snap lens spacer into place as shown in figure

below, and then reattach to optic. If image size does not increase,

remove lens spacer or that phone and optic combination.

Q2: The top clamp touches the round corner of my phone not the top flat edge of my phone.What do I do?

A2: This is normal for some models of phones.Just push as flush to rounded edge as possible and lock top clamp as normal.

Q3: I can’t align my phone vertically with the top clamp.It won’t fit.What

should I do? Fig. 21

A3: If you go through the alignment process (Fig.7-11), and there is no way to

achieve vertical alignment because it’s restricted by the top clamp, try

removing your phone case.

Alternatively, you can remove top clamp assembly using screw as shown in

Fig. 21. For this configuration, you will not be able to save your vertical

alignment between uses.Your phone will have to be adjusted for vertical

positioning each time it’s placed within the adapter.We recommend you save

these four parts for use with other phones, and you can reassemble the top

clamp as shown as in Fig.22.

Fig. 22

Q4: Can I use this on my riflescope?

A4: No, it is not recommended because of the long spacing required between the eyepiece of a riflescope and your eye so that the

image is very small on your phone screen.Also, we do not suggest using a firearm with the adapter on a riflescope, due to recoil.

Q5: My image is not centered or is not a complete round image,

what is wrong?

A5: Adjust phone alignment in vertical direction using top clamp

(Fig. 10), and in horizontal direction by using alignment screw

(Fig. 8). Check that phone is flat on adapter (Fig.6), and adapter

is fllush with optic (Fig. 17).

Q6: My phone rotates on the eyepiece when used in landscape (horizontal) mode.What should I do?

A6: If the eyepiece can rotate on your optic, then you can try the following:

1. If your eyepiece can rotate outward, then you must place adapter in orientation to counter the rotation.

2. If the eyepiece has any method to secure from rotation such as a screw set, use it to lock down the eyepiece.

3. If above solutions are not possible or do not work for your application, it may not be possible to use in this mode.Please use only in

portrait (vertical mode).

FREQUENTLY ASKED QUESTIONS CONTINUED:

Q7: Why am I getting reflections and/or glare in my image?

A7: If there are bright spots in the image itself, this may occur with indor lighting. Please avoid overhead lighting or

change the angle of the lighting relative to the phone. Also, please use without flash to avoid reflections and/or

glare in photos.If there’s glare on your phone screen that makes image hard to view, increase brightness setting

on phone and view from a position with less overhead light.

Q8: My other phone camera or flash is covered by the adapter.Why is that?

A8: First, we recommend using the device with only the primary rear camera. If problems perist, please contact

customer support. Second, the flash can be covered, and is not needed for use with optic.We recommend flash

setting is turned off at all times when using adapter.

Q9: I have a large eyepiece, but it seems like it won’t fit or it’s too tight to get one, what do I do?

A9: For eyepieces at the maximum range (58-62mm), the adapter must be opened to its maximum, and then

some pressure must be used to push the adapter over the eyepiece.Any eyepiece beyond 62mm in external

diameter should not be used with this adapter. For these largest eyepieces, do not use the optic lock. Also, it’s

important not to leave the adapter attached to these largest eyepieces for longer than two continuous hours, as it

could cause permanent wear to the springs.

Q10: The adapter is sagging on the eyepiece and not staying flush, what do I do?

A10: Make sure once the adapter is flush on the optic, to use the optic lock as shown in Fig.18.

Q11: Does this work on a tripod?

A11: The adapter itself does not have a tripod mount. However, for best stabilized images and videos, we suggest

the optic used is mounted to a tripod.

TIPS AND TRICKS:

PHOTOGRAPHY

• Tap object of interest on your phone screen to autofocus.

• For videos, tap and hold object of interest on phone screen for a second to lock focus.Tap again to release the focus lock.

• In low light conditions, turn your phone screen brightness to its lowest level.The rubber parts glow in the dark making it easier to use

the adapter.

• For long sessions, try using battery cases or phone chargers to prevent your battery from draining.

APPS

• Share photos and videos through various apps (e.g.FaceTime, Messages, Facebook, Instagram, etc.)

• Apps that allow you to sex exposure and focus manually can expand the potential of the adapter.This is especially helpful for

telescopes to set longer exposure times to get the best images of sky objects.

STABILIZATION

• To prevent shaking:

1. Use your headphones.Volume butter will now act as shutter button.

2. Attach to tripod.

•Many phones have image stabilization features. Check your phone and turn on this feature if available. If not, there are camera aps with

stabilization features.

~----------------------,,

SMARTPHONE SIZING GUIDE ,

your phone (in its

case)

fits in"portrait"orientation between

the 2arrows,

will

fit

the

HookUpz™2.0

Adapter.

-------------

1 OPTIC SIZING GUIDE I

OPTIC SIZING INSTRUCTIONS:

1. Place your optic's eyepiece inside one ofthe

two circles on the left.

2. If your optic's eyepiece fits in between the

25mm to 58mm circles, then the HookUpz 2.0

will fit your optic.

Note: Can accomodate eyepieces up to 60mm.

Push firmly to secure.

DOES

NOT

FIT

IRREGULAR

SHAPE

EYEPIECES

RIFLESCOPES:

58mm

Diagram is to scale.

19 19

CLEANING / STORAGE:

• Adapter should be cleaned with a soft, damp microfiber cloth only. Do not use any chemicals, abrasives, or solvents.

• To avoid damage, always store adapter in protective case when not in use.

• Do not leave item attached to optical device as this may weaken the springs over time.

• Store in dry area at room temperature.

˜°˛˝˙ˆˇ˘˝°ˆ˝ ˝˘˙ˆˇ˘˝°ˆ˝ ˝˘˙ˆˇ˘˝°ˆ˝

Customer Service: If you experience any difficulties,

please contact us and we will be happy to help you.

For warranty information, visit www.carson.com/warranty

www.carson.com

Carson Optical 2070 5th Avenue, Ronkonkoma, NY 11779 | Tel: 631-963-5000

Inhaltsverzeichnis

Andere Carson Motorisiertes Spielzeugauto Handbücher

Carson

Carson X10ET-XL Beat Warrior Bedienungsanleitung

Carson

Carson Night Racer 2.4 GHz Bedienungsanleitung

Carson

Carson X16 Mini Warrior Bedienungsanleitung

Carson

Carson Flix Bus 2.4 GHz Bedienungsanleitung

Carson

Carson X-Crawlee Pro Bedienungsanleitung

Carson

Carson Specter Bedienungsanleitung

Carson

Carson Nano Racer Bedienungsanleitung

Carson

Carson CE-10T Brushless NEW GENERATION Bedienungsanleitung

Carson

Carson X10ET-XL Beat Warrior Bedienungsanleitung

Carson

Carson Race Rebel Bedienungsanleitung

Carson

Carson Desert Warrior 3.0 Bedienungsanleitung

Carson

Carson Speed Shark 2.4 GHz Bedienungsanleitung

Carson

Carson X8N Chassis Bedienungsanleitung

Carson

Carson SWAT Bedienungsanleitung

Carson

Carson 1st Go-Kart RTR 103016 Bedienungsanleitung

Carson

Carson 1st Go-Kart RTR electric Bedienungsanleitung

Carson

Carson 500404067 Bedienungsanleitung

Carson

Carson X10N Onroad Chassis Bedienungsanleitung

Carson

Carson Stormracer Extreme 103013 RTR Bedienungsanleitung

Carson

Carson 507014 Bedienungsanleitung

Carson

Carson Mountain Warrior Sport 2.0 Bedienungsanleitung

Carson

Carson Crawler Bedienungsanleitung

Carson

Carson UNIMOG U300 Mercedes Benz Bedienungsanleitung

Carson

Carson Virus 4.0 GP V21 Bedienungsanleitung

Beliebte Motorisiertes Spielzeugauto Handbücher anderer Marken

Eduard

Eduard Humber Scout Car Mk.I exterior Bedienungsanleitung

Traxxas

Traxxas 4995X Bedienungsanleitung

Jamara

Jamara VW T1 Bus Bedienungsanleitung

REVELL

REVELL 68 CHEVY CHEVELLE SS 396 Bedienungsanleitung

Schumacher

Schumacher Pro Cat Bedienungsanleitung

Tamiya

Tamiya TT-01 TYPE E Bedienungsanleitung

Eduard

Eduard Krupp Protze 6x4 1/48 Bedienungsanleitung

New Bright

New Bright 61072UEP Bedienungsanleitung

Team Durango

Team Durango DEX410v5 Bedienungsanleitung

Jamara

Jamara Mercedes Actros Muldenkipper 2,4 GHz Bedienungsanleitung

PLAYMOBIL

PLAYMOBIL 9536 Bedienungsanleitung

Atomic

Atomic BZ3 Bedienungsanleitung

Aiyaplay

Aiyaplay 370-290V00 Bedienungsanleitung

Power Wheels

Power Wheels GRJ53 Bedienungsanleitung

ZEROTRIBE

ZEROTRIBE Zetricks ZT1144 Bedienungsanleitung

INJUSA

INJUSA 412 Bedienungsanleitung

Maverick

Maverick MSC-30BR-WP Bedienungsanleitung

Land of B.

Land of B. Rollin' Riders Bedienungsanleitung