CARVIN SANICLEAR40 Technisches Datenblatt

M10083

2019-4029

2019-11-13

Cell SANICLEAR40

READ THE LABEL AND OPERATION AND INSTALLATION MANUAL of the “SANICLEAR40 system” thoroughly

before the installation or usage of this replacement cell.

Replacement Cell for the SANICLEARSANICLEAR system (Canada)

REGISTRATION N° (30794) PEST CONTROL PRODUCTS ACT

This cell must only be used with this model of SANICLEAR40 system.

Tel.: +1. 450.250.4500 • Fax: +1.450.250.4501

Support: 1.866.979.4501

CARVIN POOL EQUIPMENT

4000 Boul. Casavant Ouest – Saint‐Hyacinthe (Québec) Canada J2S 9E3

www.carvinpool.com

CELL SANICLEAR40

Electrolytic Chlorine Generator (Canada)

DOMESTIC

CONTROLS THE LEVEL OF BACTERIA AND ALGAE

in pools and hot tubs

REGISTRATION N° 30794.

PEST CONTROL PRODUCT ACT.

READ THIS LABEL AND OPERATION AND INSTALLATION MANUAL BEFORE USING.

PRECAUTION:

A maximum of 170,000 Litres (45,000 Gallons) of water can be treated with one Cell SANICLEAR40 Chlorine generator system unit.

WARNING

Operating the SANICLEARSANICLEAR system without water flow through the SANICLEARSANICLEAR

system cell can cause a build‐up of flammable gases which can result in fire or explosion.

The SANICLEARSANICLEAR system protects itself against this condition via the FLO sensor by cutting off the power to the

SANICLEARSANICLEAR system cell whenever flow is not detected. The SANICLEARSANICLEAR system MUST be wired to the same circuit

as the filter pump. This ensures that the SANICLEARSANICLEAR system will only generate chlorine when the filter pump is providing

flow. The SANICLEARSANICLEAR system generates a maximum output of hypochlorous acid equivalent to 0.54 kg of free chlorine per

day.

KEEP OUT OF REACH OF CHILDREN

Do not use this device with bromide products

NOTICE TO USER! This pest control product is to be used only in accordance with the directions on the label. It is an offence under the

Pest Control Products Act to use this product in a way that is inconsistent with the directions on the label.

SWITCH: (The switch is ignored when operation is Remotely Controlled)

Super‐Chlorinate: Chlorine is produced at the maximum rate, regardless of the "Desired Output %" dial for the remainder of the

current filtering period (maximum 24 hours).

Auto: Chlorine is produced at the rate determined by the "Desired Output %" dial.

Off: Chlorine production is turned OFF. The power is controlled by the filter pump timer.

CHLORINE LEVEL DIAL:

(The Desired Output dial is ignored when operation is Remotely Controlled)

Adjust the "Desired Output %" dial to control the amount of chlorine produced. Periodically

check the pool chlorine level and adjust the dial up or down as required.

For swimming pools, an amount of 1‐3 ppm of free chlorine must be maintained.

For Hot tub, an amount of 3‐5 ppm of free chlorine must be maintained.

LCD DISPLAY: Displays salt level in ppm (parts per million).

M10077EN

ELECTRICAL RATINGS:

All wiring must conform to Canadian electricity code and to local and NEC/CEC codes. Copper wire only. PRECAUTION:

Connect only to a circuit protected by a class‐A ground fault interrupter.

Power: 110 à 130 V CA, 2A, 50/60Hz or 220 à 250 V CA, 1A, 50/60Hz

Timer: Connect to load side. Remote Control unit: Connect to line power

SUITABLE FOR INDOOR OR OUTDOOR MOUNTING

Imported by:

CARVIN POOL EQUIPMENT

4000 Boul. Casavant Ouest – Saint‐Hyacinthe (Québec) Canada J2S 9E3

www.carvinpool.com

LED Indicator

Flashing

Continuous

Power

Power is present.

Generating

Water is too hot or too cold to operate

Chlorine is being produced

Super Chlorinate

Super Chlorinate—Chlorine generation is at 100%

regardless of "Desired Output" setting.

Remote Controlled

Remote Control is in Service or Time‐Out mode—

the SANICLEARSANICLEAR system switch and dial

temporarily control operation.

Remote control System is controlling the

operation of the SANICLEARSANICLEAR

system.

No Flow

The CGS System is temporarily paused after the

flow is established.

Water is NOT flowing through the

SANICLEARSANICLEAR system cell— Chlorine

generation is halted.

Check Salt

Salt is below 2600 ppm. SANICLEARSANICLEAR

system is working at reduced efficiency. Check

SANICLEARSANICLEAR system cell and clean if

necessary. If problem persists, have the salt level

professionally tested before adding salt to the

pool.

Salt is below 2300 ppm. Chlorine generation is

halted. Check SANICLEAR system cell and clean if

necessary. If problem persists, have the salt level

professionally tested before adding salt to the pool.

High Salt

Salt concentrations above 3800 ppm: everything is

working well for the moment but the production of

chlorine could halt if the temperature rises.

Cell current too High. Chlorine generation is halted.

See operation manual for directions on decreasing

salt level.

Inspect Cell

Reduced SANICLEAR system cell efficiency or

scheduled 3 month cell inspection time. Inspect

SANICLEAR system cell and clean if necessary, and

press display button for 3 seconds to turn off

flashing indicator.

SANICLEAR system cell efficiency greatly reduced.

Inspect SANICLEAR system cell and clean if necessary. If

SANICLEAR system cell is clean it may be at the end of

its life and needs to be replaced.

Inspect SANICLEAR system cell every 3 months/clean if necessary

M10077EN

CARVIN POOL EQUIPMENT Inc.

4000 Boul. Casavant Ouest – Saint-Hyacinthe (Québec) Canada J2S 9E3

Tel.: 1.450.250.4500 • Fax: 1.450.250.4501 Support: 1.866.979.4501

www.carvinpool.com

M10077EN

SANICLEAR

SANICLEAR Chlorine Generator system

For pools and hot tubs

SANICLEAR40

CONTROLS THE LEVEL OF BACTERIA AND ALGAE

In pools and hot tubs

DOMESTIC

OPERATION AND INSTALLATION MANUAL

REGISTRATION NUMBER 30794 PEST CONTROL PRODUCTS ACT

WARNING: Operating the SANICLEAR Chlorine generator system without any water flow through

the cell can cause a build‐up of flammable gases which can result in

FIRE OR EXPLOSION

READ THE LABEL AND ATTACHED MANUAL BEFORE USING EQUIPMENT

M10077EN

CONTENTS

IMPORTANT SAFETY INSTRUCTION……. 23

INSTALLATION ...............24

Flow switch.............................................................24

Cell…......................................................................25

Electrical warning…................................................26

Electrical information…...........................................26

WATER PREPARATION.......................................28

Ideal chemical Level…............................................28

Recommended salt….............................................28

Level of salt….........................................................29

Procedure for adding or remove salt…...................29

Chart for salt requirement… ...................................30

Other chemical requirements..................................31

OPERATION ................... 32

Adjustment knob… .................................................32

LED status…...........................................................33

Main switch… .........................................................33

Display screen….....................................................34

Performance… .......................................................34

Maintaining the system… .......................................34

Servicing and cleaning the cell…............................35

Mild acid washing…................................................35

Opening the pool….................................................35

Closing the pool… ..................................................35

TROUBLESHOOTING.......................................36

LIMITED WARRANTY........................................ 38

REPLACEMENT PART LIST.............................40

M10077EN

IMPORTANT SAFETY INSTRUCTIONS

Make sure to take all precautions before you use electrical equipment:

SAVE THESE INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS.

KEEP OUT OF REACH OF CHILDREN.

WARNING : IMPORTANT SAFETY INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS.

Before installing this product, read and follow all warning notices and instructions which are included. Failure to

follow safety warnings and instructions can result in damage or harm to property or persons.

All electrical power should be shut off during the installation.

Do not allow children to use, touch or play with this product.

You will find in the wiring box, against the back panel, a green colored terminal. To avoid any electric shock,

this screw must be connected to the ground in the electric panel with a copper wire the same size as the circuit

conductors of the existing equipment.

One ground connection is provided on the external surface. To avoid any shocking hazard, connect the local

connecting grid of the swimming pool, the spa, or hot tub to these terminals with a copper conductor of at least

8 AWG for US/6 AWG for Canada (not smaller).

Any metal components such as rails, drains, ladders, or other hardware located within 10 feet (3 meters) of the

pool, spa or hot tub should be connected to the ground with proper copper conductors of at least 8 AWG for

US/ 6 AWG for Canada (not smaller).

WARNING: To reduce the risk of injury, service should only be carried by a qualified pool service professional.

Do not use this device with bromide products

NOTICE TO USER: This pest control product is to be used only in accordance with the directions on the label. It is

an offence under the Pest Control Products Act to use this product in a way that is inconsistent with the directions on

the label.

For proper sanitation, Hot tubs must be completely drained periodically. The number of days between COMPLETE SPA

DRAINAGE is equal to the volume of spa water in litres, divided by 10 times the maximum number of daily spa users.

Refill spa with water and repeat the DIRECTIONS FOR USE of the SANICLEAR Chlorine generator system.

People with a medical condition should consult a physician before entering a pool or spa.

Maximum spa water usage temperature is 40°C. Duration in spa water at 40°C should not exceed 15 minutes.

WARNING for Spa owner: this product is not recommended for acrylic or any other type of plastic spa. The use of

this Chlorine Generator with this type of spa may void the Hot tubs manufacturer’s warranty. Carvin Pool Equipment

will not be held responsible of this warranty if the user uses this product with acrylic or plastic spa. See with your

dealer if this product is recommended for your application.

c(ETL)us Listed certified to UL1081 and CSA-C22.2 NO.108 2001 R2010

M10077EN

INSTALLATION

Installation must be performed in accordance with all Local NEC codes.

Preparing the Pool Water:

Check the pool water chemistry and balance BEFORE activating the salt chlorinator. It is recommended that

you consult a pool professional for the initial water balancing each season.

NOTE: At the beginning of each season, add metal remover and polymer based (non copper) algaecide to the

pool, as per the manufacturer’s instructions. This operation will ensures a rapid, trouble free transfer to the

SANICLEAR chlorine generation system.

The SANICLEAR control panel is suitable for outdoor mounting. It must be installed a minimum of 5 ft. (1,5

meters) of distance (or more depending on local codes requirements) from the pool or spa.

The control of the SANICLEAR control box is designed to be mounted in a vertical position on a flat surface

with the pre-punched holes downwardly facing. Because the case also used to disperse the heat, it is very

important that the four sides of the control are not blocked to serve as ventilation openings.

Do not mount the case in a closed panel or confined area.

Make sure the salt chlorinator installation does not interfere with the potable water connection. Verify local

plumbing codes.

The switches (cell and flow) are connected in the return line to the pool. They are installed after all the other

pool equipment like filter, heater, solar, etc. The necessary plumbing components are provided

2” (51mm) rigid PVC piping installation for in ground pools

Refer to the diagram on next page for plumbing:

When you install the flow switch insure that the position of the arrow on the flow switch (located on top) is

in the same direction of water flow. See below drawing.

M10077EN

Use the unions provided and tighten by hand at both ends of the cell for a perfect watertight seal. For pool or

spa with spillover systems, use the fig #2 or #3 below to allow that chlorination is functional for both the pool

and spa during spillover but when using the spa only it will prevent over chlorination.

M10077EN

DANGER: RISK OF ELECTRIC SHOCK THAT CAN RESULT IN SERIOUS INJURY OR DEATH.

Before proceeding with any wiring, the power at the circuit breaker must be turned off. Make sure to follow

all electrical codes (local and NEC). For safe operation, the Salt chlorinator must be installed properly by

being grounded and bonded.

Input power for stand-alone use:

VERY IMPORTANT: The SANICLEAR system is to be powered only when the pump is running.

For proper wiring connections, refer to the diagram below and to the wiring label on Salt chlorinator. The salt

chlorinator is shipped with the 120V configuration jumpers stuck on the case cover. Until the jumpers are

installed for the desired voltage, the unit should NOT be turned on.

For Canada: Make sure the SANICLEAR chlorine generation system is connected to a circuit protected by a

ground fault interrupter class “A”. Make sure you connect the GROUND wire to the green ground screw

located on the INSIDE WALL of the enclosure.

Inhaltsverzeichnis

Andere CARVIN Schwimmbadfilter Handbücher

CARVIN

CARVIN OLLO 94180186 Bedienungsanleitung

Beliebte Schwimmbadfilter Handbücher anderer Marken

Davey

Davey PoolSweepa FloorCova Bedienungsanleitung

Jandy

Jandy DEL Series Bedienungsanleitung

ProMinent

ProMinent DULCODOS Bedienungsanleitung

Hayward

Hayward Perflex Bedienungsanleitung

TMC Aquarium

TMC Aquarium V2Skim Pro Bedienungsanleitung

Swim & Fun

Swim & Fun PRO CLASSIC basic Bedienungsanleitung

Swim & Fun

Swim & Fun EASY SALT Bedienungsanleitung

SMC Networks

SMC Networks SMC20TA-2500 PPM Bedienungsanleitung

T.I.P.

T.I.P. SPF 180 Bedienungsanleitung

Waterway

Waterway Clear Water II Bedienungsanleitung

Steinbach

Steinbach S1 Bedienungsanleitung

EHEIM

EHEIM 350 Bedienungsanleitung

Davey

Davey EcoPure DEP2140 Bedienungsanleitung

JUWEL Aquarium

JUWEL Aquarium EccoSkim Bedienungsanleitung

POLYGROUP LIMITED

POLYGROUP LIMITED SFS600 Filter System with F600C Pump Bedienungsanleitung

Pentair Pool Products

Pentair Pool Products Filter CFW Series Bedienungsanleitung

Oase

Oase Skimmer 250 Bedienungsanleitung

Oase

Oase CrystalSkim 350 Bedienungsanleitung