CAS WEIGHING SOLUTION SWII PLUS Series Bedienungsanleitung
2
3
PRECAUTIONS 4
PREFACE 6
NAMES AND FUNCTIONS 6
OPERATIONS 8
1. Simple Weighing Mode 8
2. Weighing with Tare 8
3. Changing Unit of Weight 9
4. Hold Function 9
5. Comparator Function 10
6. Counting Function 11
7. Setup Mode 14
BATTERY MAINTENACE 15
ERROR MESSAGE 15
SPECIFICATIONS 16
4
5
6
Thank you for purchasing CAS SWΙΙ PLUS series.
These series have been designed with CAS reliability, under rigid quality control
and with outstanding performance. Your special departments can enjoy these
high quality reliable CAS products.
We believe that your needs will be satisfied and you will have proper reliability.
This manual will help you with proper operation and care of the SWΙΙ-W.
Please keep it handy for future reference.
NAMES AND FUNCTIONS
OVERALL VIEW
7
DISPLAY & KEYBOARD
KEY FUNCTIONS
KEYS FUNCTIONS
Used to set the zero point.
Used to convert the unit of weight.
(If you press the button long time, Unit is converted)
Used to input or cancel the weight of tare.
Used to make the weight of commodity stable.
This weight is average value.
Used to change the unit of weight, and shown as following sequence
on the display. [Kg] [WL on or off] [PCS] [Kg]
(If you press the button long time, Mode is changed)
Used to turn on and off the scale.
8
●Turn on the scale by pressing key. Then, the display will show all the
segments and count up "0" to "9". You may stop this automatic counting by
pressing the key.
●When you turn on the display, make sure that platter is empty. Otherwise,
display will show "Err 1", an error of initial zero range. Please refer to "ERROR
MESSAGE" section for more information on page15.
●When the weight becomes stable the display shows the stable sign ( ) on.
●You may need to make it "0.000" by pressing key unless the display
indicate "0.000" under the empty platter.
1. Simple Weighing Mode
①Place a commodity on the platter.
②Remove the commodity from the platter.
2. Weighing with Tare
●TARE means the weight of container being used for a commodity.
●TARE key function is to subtract the weight of the container from full weight loaded
Place a container on①the platter.
9
②Press the key.
③Place a commodity into the container, then
the display will show only the weight of the
commodity.
④Remove container and commodity, then the
display will show the weight of the container
with "-" symbol.
⑤Press the key, then display will
show the "0.000".
3. Changing Unit of Weight
●Press the key a few seconds.
You may select kg, or g as the unit of weight.
4. Hold Function
①When the weight is unstable, press the
key
②Then "HOLD" will be displayed twice
③Then average value will be show twice And
the "HOLD" function will be removed
automatically
10
5. Comparator Function - HI / LOW Limit Setting
①Press the key until the display
shows "WL OFF" (Press the key for a
few second). "WL OFF" means that
comparator function is not activated..
②Press key to activate this function.
The display shows "WL ON".
③Press key once to set up the low
limit. The display shows "0.000" and the first
number flashes..
④Press the key to have number
increase. To move flash to next digit, press
the key.
⑤Press key to set up HIGH limit. The
display shows "2.000" and you can change
these numbers by pressing key.
If you want to move to next digit you can go by
pressing key.
⑥If you set up HIGH limit you can go out by
pressing key, and "End" message on
the display.
⑦If you set up HIGH limit and LOW limit incorrectly, "Err" will be shown on the display. Then
you may need to set it up again. For example, setting LOW LIMIT=2.990 kg and HIGH
LIMIT=1.990 kg this is incorrect setting because HIGH limit is lower than the LOW limit. When
HIGH and LOW limit are set as the same or above maximum capacity it still shows "Err"
message.
11
⑧If you want to go back to the simple
weighing mode just press key twice.
(Press the key for a few second).
⑨Suppose that the HIGH limit and LOW limit
are set up as 2.990kg and 1,990kg
respectively.
If the weight loaded is 2kg between HIGH and
LOW limit the display shows "OK" and the
scale continues to beep slowly.
If the weight loaded is above 2.990kg, HIGH
limit, the scale continues to beep rapidly.
6. Counting Function
●Counting without Tare
①Initial display as above.
②Press key twice to go to sample unit
selection mode. (Press the key for a
few second)
③Press key to select the number of
sample unit. You can select 10, 20, 50, 100,
200, or 500 as a sample unit.
④If you select "P_10" as a sample unit, then
please put 10 sample units on the scale.
Then press key to set sample units.
⑤Put all of commodities you wish to count,
and then check the number of pieces on
display.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere CAS Skala Handbücher
CAS
CAS CASTON II Bedienungsanleitung
CAS
CAS PW-II Bedienungsanleitung
CAS
CAS CL-3000 Series Bedienungsanleitung
CAS
CAS HE-52 Bedienungsanleitung
CAS
CAS BF-1410 Bedienungsanleitung
CAS
CAS EB Series Bedienungsanleitung
CAS
CAS PR-T Series Bedienungsanleitung
CAS
CAS BF-1255B Bedienungsanleitung
CAS
CAS K6 Bedienungsanleitung
CAS
CAS BW-1N Bedienungsanleitung
CAS
CAS CL5500 Series Bedienungsanleitung
CAS
CAS SW-II Series Bedienungsanleitung
CAS
CAS PD-I Gebrauchsanweisung
CAS
CAS PW Series Bedienungsanleitung
CAS
CAS PDI Series Bedienungsanleitung
CAS
CAS CI-200 Series Bedienungsanleitung
CAS
CAS DL Series Bedienungsanleitung
CAS
CAS Road Weigher RW-2601P Bedienungsanleitung
CAS
CAS CL5000J Series Bedienungsanleitung
CAS
CAS ER PLUS SERIES Bedienungsanleitung
