Casio EX-Z3 - 4 Gebrauchsanweisung
USING A MEMORY CARD
118
USING A MEMORY CARD
You can expand the storage
capabilities of your camera by using
a commercially available memory
card (SD memory card or
MultiMedia Card). You can also
copy files from built-in flash
memory to a memory card and from
a memory card to flash memory.
• Normally, files are stored in built-in flash memory. When
you insert a memory card, however, the camera
automatically stores files to the card.
• Note that you cannot save files to built-in memory while a
memory card is installed in the camera.
IMPORTANT!
• Make sure you turn off the camera before inserting or
removing a memory card.
• Be sure to orient the card correctly when inserting it.
Never try to force a memory card into the slot when
you feel resistance.
• See the instructions that come with the memory card
for information about how to use it.
• Certain types of cards can slow down processing
speeds.
• SD memory cards have a write protect switch, which
you can use to protect against accidental deletion of
image data. Note, however, if you write protect an
SD memory card, you must remove write protection
whenever you want to record to it, format it, or delete
any of its files.
USING A MEMORY CARD
119
Using a Memory Card
To insert a memory card into the camera
1.
While pressing the battery
cover on the bottom of the
camera, slide the cover in
the direction indicated by
the arrow, and then swing it
open.
2.
Positioning the memory
card so its front is facing in
the same direction as the
camera’s monitor screen,
carefully slide it into the
card slot.
To remove a memory card from the
camera
1.
Press the memory card into
the camera and then release
it. This will cause the card to
come part way out of the
camera.
2.
Pull the memory card out of the slot.
BackFront
3.
Swing the battery cover
closed, and then slide it in
the direction indicated by
the arrow.
USING A MEMORY CARD
120
Formatting a Memory Card
Formatting a memory card deletes any data already stored
on it.
IMPORTANT!
• Be sure to use the camera to format a memory card.
Formatting a memory card on a computer and then
using it in the camera can slow down data
processing by the camera. In the case of an SD card,
formatting on a computer can result in non-
conformity with the SD format, causing problems with
compatibility, operation, etc.
• Note that data deleted by a memory card format
operation cannot be recovered. Check to make sure
you do not need any of the data on the memory card
before you format it.
• Formatting a memory card that contains files deletes
all the files, even those that are protected (page 97).
IMPORTANT!
• Never insert any other object besides a memory card
into the camera’s card slot. Doing so creates the risk
of damage to the camera and card.
• Should water or any foreign object ever get into the
card slot, immediately turn off the camera, remove
the battery, and contact your dealer or nearest
CASIO authorized service center.
• Never remove a card from the camera while the
operation lamp is flashing. Doing so can cause the
file save operation to fail, and even damage the
memory card.
USING A MEMORY CARD
121
Memory Card Precautions
• Use only an SD memory card or a MultiMediaCard with
this camera. Proper operation is not guaranteed when
any other type of card is used.
• Electrostatic charge, electrical noise, and other
phenomena can cause data to become corrupted or even
lost. Always make sure that you always back up important
data on other media (MO disc, computer hard disk, etc.).
• If a memory card starts to behave abnormally, you can
restore normal operation by reformatting it. However, we
recommend that you always take along more than one
memory card whenever using the camera far away from
the home or office.
• We recommend that you format a memory card before
using it for the first time after purchasing it, or whenever
the card you are using seems to be the cause of
abnormal images.
• Before starting a format operation, check to make sure
that the battery is fully charged. Power interruption during
the format operation can result in improper formatting,
and even damage the memory card and make it
unusable.
1.
Load the memory card into the camera.
2.
Turn on the camera. Next, enter the REC
mode or PLAY mode and press [MENU].
3.
Select the “Set Up” tab, select “Format”, and
then press [왘].
4.
Use [왖] and [왔] to select “Format”, and then
press [SET].
• To exit the format operation without formatting,
select “Cancel”.
USING A MEMORY CARD
122
4.
Use [왖] and [왔] to select “Built-in Card”,
and then press [SET].
• This starts the copy operation and displays the
message “Busy... Please wait..”.
• After the copy operation is complete, the monitor
screen shows the last file in the folder.
Copying Files
Use the procedures below to copy files between built-in
memory and a memory card.
IMPORTANT!
• Only snapshot and movie files recorded with this
camera can be copied. Other files cannot be copied.
To copy all the files in built-in memory to
a memory card
1.
Load the memory card into the camera.
2.
Turn on the camera. Next, enter the PLAY
mode and press [MENU].
3.
Select the “PLAY” tab,
select “Copy”, and
then press [왘].
USING A MEMORY CARD
123
To copy a file from a memory card to
built-in memory
With this procedure you can copy one file at a time.
1.
Perform steps 1 through 3 of the procedure
under “To copy all the files in built-in memory
to a memory card”.
2.
Use [왖] and [왔] to select “Card Built-in”,
and then press [SET].
3.
Use [왗] and [왘] to select the file you want to
copy.
4.
Use [왖] and [왔] to select “Copy”, and then
press [SET].
• This starts the copy operation and displays the
message “Busy... Please wait..”.
• The file reappears on the monitor screen after the
copy operation is complete.
• Repeat steps 3 through 4 to copy other images, if
you want.
5.
Press [MENU] to exit the copy operation.
NOTE
• Files are copied to the folder in built-in memory
whose name has the largest number.
VIEWING IMAGES ON A COMPUTER
124
VIEWING IMAGES ON A COMPUTER
After using the USB cradle to establish a USB connection
between the camera and your computer, you can use your
computer to view images in file memory and copy images
to your computer’s hard disk or other storage media. In
order to do this, you first need to install the USB driver
located on the CD-ROM that comes bundled with the
camera onto your computer.
Note that the procedure you need to perform depends on
whether you are using computer running under Windows
(see below) or a Macintosh (see page 129).
Using the Camera with a Windows
Computer
The following are the general steps for viewing and copying
files from a computer running under Windows. You can find
details about each operation in the procedures that follow
below. Note that you should also refer to the
documentation that comes with your computer for other
information about USB connections, etc.
1. If you are running Windows 98, Me, or 2000, install
the USB driver onto your computer.
•You need to perform this step only once, the first
time you connect to your computer.
•If you are running Windows XP, you do not need to
install the USB driver.
2. Use the USB cradle to establish a connection between
the camera and computer.
3. View and copy the images you want.
VIEWING IMAGES ON A COMPUTER
125
1.
What you should do first depends on whether
your computer is running under Windows 98/
Me/2000 or Windows XP.
■Windows 98/Me/2000 Users
•Start from step 2 to install the USB driver.
•Note that the example installation presented here
uses Windows 98.
■Windows XP Users
•Installation of the USB driver is not required, so jump
directly to step 6.
2.
Set the bundled CD-ROM into the CD-ROM
drive of your computer.
3.
On the menu screen
that appears, click the
language button in the
upper left corner of the
display, and then
select a language from
the list that appears.
4.
Click [USB driver] and then [Install].
•This starts installation.
•The following steps show installation under the
English version of Windows.
5.
On the screen that appears after installation
is complete, select the “Yes, I want to restart
my computer now.”check box and then click
[Finish] to restart your computer.
IMPORTANT!
•Do not try to establish a connection between the
camera and computer before installing the USB
driver onto the computer.
•If you want to transfer files from the camera’s built-in
memory to a computer, make sure there is no
memory card loaded in the camera before you place
it onto the USB cradle.
VIEWING IMAGES ON A COMPUTER
126
USB port
Connector A
USB cable
(bundled)
[USB]
Connector B
6.
Connect the bundled AC adaptor to the [DC IN
5.3V] connector of the USB cradle, and then
plug it in to a household power outlet.
•Note that the shape of the AC adaptor depends on
the area where you purchased the camera.
7.
Connect the USB cable that comes bundled
with the camera to the USB cradle and your
computer’s USB port.
•Take care when connecting the USB cable to the
USB cradle or your computer. USB ports and cable
plugs are shaped for proper positioning.
•Plug the USB cable plugs into the ports securely, as
far as they will go. Proper operation is not possible if
connections are not correct.
○○○○○○○○○○○○○○○○○○○○○○○○○○○
VIEWING IMAGES ON A COMPUTER
127
PHOTOCHARGEUSB
DISP
MENU
SET
REC
PLAY
8.
After making sure the camera is turned off,
place the camera onto the USB cradle.
•Do not place the camera onto the USB cradle while it
is turned on.
9.
Press the USB cradle’s [USB] button.
•This will cause the “New Hardware...”dialog box to
appear on the computer screen as the computer
automatically detects the camera’s file memory. After
you install the USB driver, “New Hardware...”dialog
box will no longer appear when you perform the
above steps to establish a USB connection.
•Pressing the [USB] button enters the USB mode,
which causes the USB cradle’s [USB] lamp to light
green (page 158).
•At this point, some operating systems will display a
“Removable Disk”dialog box. If your operating
system does, close the dialog box.
DISP
MENU
SET
REC
PLAY
PHOTO CHARGE USB
[USB] button
[USB] lamp
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Casio Digitalkamera Handbücher
Casio
Casio EX-FC100BK Bedienungsanleitung
Casio
Casio EXILIM K1123PCM2DMX Bedienungsanleitung
Casio
Casio EX-ZR5100 Bedienungsanleitung
Casio
Casio EXILIM EX-ZS5 Bedienungsanleitung
Casio
Casio EX-S1 - EXILIM Digital Camera Fehlerbehebungshandbuch
Casio
Casio Exilim EX-S770 Bedienungsanleitung
Casio
Casio EX-FR10 Bedienungsanleitung
Casio
Casio Exilim EX-FH100 Bedienungsanleitung
Casio
Casio QV-3000EX/Ir Bedienungsanleitung
Casio
Casio QV-10 Bedienungsanleitung
Casio
Casio Exilim EX-Z30 Bedienungsanleitung
Casio
Casio QV-3500EX Montage- und Wartungsanleitung
Casio
Casio EX-S3 - 4 Gebrauchsanweisung
Casio
Casio EX-Z2000 - EXILIM Digital Camera Bedienungsanleitung
Casio
Casio QV-4000 Bedienungsanleitung
Casio
Casio QV-3EX Bedienungsanleitung
Casio
Casio QV-70 Bedienungsanleitung
Casio
Casio QV-120 Bedienungsanleitung
Casio
Casio QV-780 Fehlerbehebungshandbuch
Casio
Casio EX-Z4 - EXILIM Digital Camera Bedienerhandbuch
