Casio QV-10 Montageanleitung
Repair Guide for QV-10
Contents PAGE
Requirement ..................................................................................................
Equipment and Tool ....................................................................................
Disassembly ..................................................................................................
Troubleshooting .............................................................................................
No power on .................................................................................................
Picture element is missing when print out ...................................................
Sudden power failure ...................................................................................
Assembly .......................................................................................................
Major points .................................................................................................
Data Restoring ...............................................................................................
Memory error reset ......................................................................................
Creating backup file .....................................................................................
Restoring images stored in QV-10 memory error ........................................
After Replacing the Digital PCB .....................................................................
Color Adjustment ...........................................................................................
Initializing the Flash Memory ..........................................................................
Vcom Adjustment ...........................................................................................
Appendix .......................................................................................................
Usage ..........................................................................................................
1
1
3
4
4
6
7
8
8
9
9
10
11
12
13
14
15
18
18
Vol. 1 Basic Repair
PERSONAL COMPUTER
IBM PC/AT or compatible RS-232C serial port ( D-Sub 9-pin )
MS-WINDOWS Ver 3.1 or later Mouse or other pointing devices
4MB of RAM (8MBrecommended ) 3.5" 1.44MB disk drive (for installation )
10MB available hard disk space
Color monitor ( full-color recommended)
386SX CPU or higher (486SX recommended )
SERVICE UTILITY SOFTWARE
FLASH. EXE
AMED.EXE
ADJ.EXE
LIGHT BOX HANDY 5000
for Color adjustment
COLOR FILTER LBA 3
for Color adjustment
OSCILLOSCOPE
REGULATED DC POWER SUPPLY
PHOTO DIODE
Requirement
Equipment and Tool
-1-
SOLDERING IRONand SOLDER
KOTELYZER
ANALOG VOLTMETER
TWEEZERS and SCREW DRIVER
CABLE
Equipment and Tool
-2-
PHOTO SENSOR AMP.
Remove the two screws from the lower case.
Remove the two screws from the lower case.
Pull out the lowercase.
Take the battery cover.
Pull out the keyborad PCB from the digital PCB.
Disassembly
-3-
Procedure
No power on
Check the power switch.
Check the fuse(FU500) by using multimeter.
Take the fuse (FU-100) by using multimeter.
Replace the backlight or the LCD.
Pull out the flat cable fromthe digital PCB.
Troubleshooting
-4-
Procedure
Remove the three screws from the upper case.
Remove the connector from the linear PCB.
Loose the connectorthen therelease hook. Pull out
the linear PCB.
Remove the four screws from the upper case.
Replace the backlight.
-5-
Procedure
Replace the LCD.
Vcom adjustment is necessary when changed the
LCD.
See page 14.
Defective the camera unit.
Remove the two screws.
Pull out the two connectors.
Pull out the two flat cables from the connectors.
Replace the camera unit.
Color adjustment is necessary when changed it.
See page 13.
Picture element is missing when print out.
-6-
Procedure
Poor soldering on the power jack.
Remove the one screw from the lower case.
The coonector(s) of the power jack should be
soldered.
Sudden power failure.
-7-
Procedure
Assembly can be performed in the reverse order of
the disassemblysteps.
There are three majorpoints of assembly work.
2. Gently set the switch knob to the point of the slide
switch.
3. Push hardthe upper case with both hands in the
direction of the lower case.
Assembly
-8-
Procedure
1. Set the point of the slide switch to the switch knob.
Major points
Memory error message appears on the display, when
QV-10 finds onerror in the internal flash memory.
Install the QV-10 service utility on your computer.
Create a directory for the QV-10 service utility on drive
C.
Data Restoring
Memory Error Reset
M Space Q V 1 0D EnterPress
to create the root directory
C SpaceP Y A :O \ *
E X E Enter
.
Press
to copy the QV-10service utility on to the suitable
directory.
C:\>
C:\>md qv10
Directoryalreadyexists
C:\>copy a:\*.exe
A:\ADJ.EXE
A:\AMED.EXE
A:\FLASH.EXE
3 file(s)copied
C:\>
-9-
Procedure
Andere Handbücher für QV-10
3
Inhaltsverzeichnis
Andere Casio Digitalkamera Handbücher
Casio
Casio QV-R3 Bedienungsanleitung
Casio
Casio Exilim EX-Z750 Bedienungsanleitung
Casio
Casio camera Bedienungsanleitung
Casio
Casio Exilim EX-Z110 Bedienungsanleitung
Casio
Casio EX-M20 - 4 Bedienungsanleitung
Casio
Casio EX-FH100BK Bedienungsanleitung
Casio
Casio EXILIM EX-ZR200 Bedienungsanleitung
Casio
Casio EXILIM EX-Z690 Bedienungsanleitung
Casio
Casio QV-70 Bedienungsanleitung
Casio
Casio EX-FC150 - EXILIM Digital Camera Bedienungsanleitung
Casio
Casio Exilim EX-P600 Fehlerbehebungshandbuch
Casio
Casio EX-V8 - EXILIM Hi-Zoom Digital Camera Bedienungsanleitung
Casio
Casio Exilim EX-Z6 Bedienungsanleitung
Casio
Casio EX-TR60 Bedienungsanleitung
Casio
Casio EX-Z4 - EXILIM Digital Camera Fehlerbehebungshandbuch
Casio
Casio EXILIM EXS3DBA Bedienungsanleitung
Casio
Casio Exilim EX-Z57 Fehlerbehebungshandbuch
Casio
Casio EXILIM EX-ZR300 Bedienungsanleitung
Casio
Casio EX-Z4 - EXILIM Digital Camera Bedienungsanleitung
Casio
Casio Exilim EX-Z850 Fehlerbehebungshandbuch
