Casio E-CON2 Betriebsanleitung

E-CON2

1E-CON2 Overview

2Using the Setup Wizard

3Using Advanced Setup

4Using a Custom Probe

5Using the MULTIMETER Mode

6Using Setup Memory

7Using Program Converter

8Starting a Sampling Operation

9Using Sample Data Memory

10 Using the Graph Analysis Tools to Graph Data

11 Graph Analysis Tool Graph Screen Operations

All of the explanations provided here assume that you are already familiar

with the operating precautions, terminology, and operational procedures of

the calculator and the EA-200.

20021201

1-1

E-CON2 Overview

1E-CON2 Overview

• From the Main Menu, select E-CON2 to enter the E-CON2 Mode.

•“The E-CON2 Mode” provides the functions listed below for simple and more efficient data

sampling using the CASIO EA-200.

•1(SETUP) ...Displays a screen for setting up the EA-200.

•2(MEM) .......Displays a screen for saving EA-200 setup data under a file name.

•3(PRGM).....Performs program conversion.

•This function converts EA-200 setup data configured by E-CON2 to

a program.

•It can also be used to convert data to a program that can be run on

a CFX-9850 Series/fx-7400 Series calculator, and to transfer the

data to the calculator.

•4(START) ....Starts data collection.

•5(GRPH) .....Graphs data sampled by the EA-200, and provides tools for analyzing

graphs. GraphAnalysis tools include calculation of periodic frequency,

various types of regression, Fourier series calculation, and more.

•6(HELP) ......Displays E-CON2 help.

•Pressing the Kkey (Setup Preview) or a cursor key while the E-CON2 main menu is on

the screen displays a preview dialog box that shows the contents of the setup in the

current setup memory area.

To close the preview dialog box, press i.

About online help

Pressing the 6(HELP) key displays online help about the E-CON2 Mode.

E-CON2 Main Menu

20021201

2Using the Setup Wizard

This section explains how to use the Setup Wizard to configure the EA-200 setup quickly

and easily simply by replying to questions as they appear.

If you need more control over specific sampling parameters, you should consider using the

Advanced Setup procedure on page 3-1.

kSetup Wizard Parameters

Setup Wizard lets you make changes to the following three EA-200 basic sampling

parameters using an interactive wizard format.

•Sensor (Select Sensor):

Specify a CASIO or VERNIER* sensor from a menu of choices.

*Vernier Software & Technology

•Total Sampling Time:

Specify a value within the range of 0.01 second to 30 days.

•Sampling Time Unit (Select Unit):

Specify seconds (sec), minutes (min), hours (hour), or days (day) as the time unit of the

value you input for the total sampling time (Total Sampling Time).

Sensor-specific settings

The type of sensor you select with “Select Sensor” settings affects the settings of the Setup

Wizard as described below.

2-1

Using the Setup Wizard

•The sampling time unit (Select Unit) becomes

“

sec” and

cannot be changed.

•The sampling time unit (Select Unit) becomes

“

sec” and

cannot be changed.

•You must specify the sampling timing (Gate - Status)

and number of samples (Number of Samples).

•For details, see “Using Setup Wizard to Configure a

PhotoGate Setup” on page 2-3.

•You must specify the distance (Distance) only.

•For details, see “Using Setup Wizard to Configure a

PhotoGate Setup” on page 2-3.

•Requires sampling that is completely different from that

performed with a sensor.

•For details, see “Outputting the Waveform of a

Function through the Speaker” on page 2-4.

[CASIO] - [Mic]

[CASIO] - [SPEAKR] - [Sample]

[VERN] - [P-Gate] - [None]

[VERN] - [P-Gate] - [Pulley]

[CASIO] - [SPEAKR] - [Y=f(x)]

Affects Setup Wizard settings like this:Selecting this with “Select Sensor

”

Setup Wizard Rules

Note the following rules whenever you use the Setup Wizard.

•The EA-200 sampling channel is CH1 or SONIC.

•The trigger for a Setup Wizard setup is always the wkey.

20021201

uTo configure an EA-200 setup using Setup Wizard

Before getting started...

•Before starting the procedure below, make sure you first decide if you want to start

sampling immediately using the setup you configure with Setup Wizard, or if you want to

store the setup for later sampling.

•See sections 6-1, 7-1, and 8-1 of this manual for information about procedures required to

start sampling and to store a setup. We recommend that you read through the entire

procedure first, referencing the other sections and pages as noted, before actually trying

to perform it.

•To terminate Setup Wizard part way through and cancel the setup, press !i(QUIT).

1. Display the E-CON2 main menu (page 1-1).

2. Press 1(Setup EA-200). This displays the “Setup EA-200” submenu.

3. Press b(Wizard). This displays the “Select Sensor” screen.

4. Press 1to specify a CASIO sensor, or 2to specify a Vernier sensor. Select the

sensor you want from the menu of sensors that appears.

•Selecting a sensor (page 2-1) causes a screen for specifying the total sampling time to

appear.

2-2

Using the Setup Wizard

5. Use the number input keys to input the total sampling time. Just input a value. You will be

able to specify the unit (sec, min, hour, day) of the value you input here in step 7 of this

procedure (see "Sensor-specific settings" on page 2-1).

Note

•If you specify a total sampling time value in the range of 10 seconds to 23 hours, 59

minutes, 59 seconds, real-time graphing will be performed during sampling. This is the

same as selecting the Realtime Mode on the “Advanced Setup” screen.

6. After inputting total sampling time value you want, press w. This displays the “Select

Unit” screen.

20021201

8. Press number keys described below to specify what you want to do with the setup you

have configured.

b(Start Setup) ................ Starts sampling using the setup (page 8-1)

c(Save Setup-MEM) ...... Saves the setup (page 6-2)

d(Convert Program)....... Converts the setup to a program (page 7-1)

kUsing Setup Wizard to Configure a PhotoGate Setup

Connection of a Vernier PhotoGate requires configuration of setup parameters that are

slightly different from parameters for other types of sensors.

uTo configure a setup for PhotoGate alone

1. Perform the first three steps of the procedure under “To configure an EA-200 setup using

Setup Wizard” on page 2-2.

2. On the “Select Sensor” screen, select [VERN] - [P-Gate] - [None].

•This causes a “Gate Status” screen to appear.

2-3

Using the Setup Wizard

7. Use number keys bthrough fto specify the unit for the value you specified in step 5.

•When you select a unit, the Final Setup Wizard screen appears on the display.

•“Open” means the photo path is not blocked, while “Close” means the photo path is

blocked.

•The gate status defines what PhotoGate status should cause timing to start, and what

status should cause timing to stop.

Open-Open ......Timing starts when the gate opens, and continues until it closes and

then opens again.

Open-Close ......Timing starts when the gate opens, and continues until it closes.

Close-Open ......Timing starts when the gate closes, and continues until it opens and

then opens again.

Close-Close......Timing starts when the gate closes, and continues until it opens and

then closes again.

Final Setup Wizard Screen

20021201

2-4

Using the Setup Wizard

4. Input an integer in the range of 1 to 255 to specify the number of samples.

5. Perform step 8 under “To configure an EA-200 setup using Setup Wizard” on page 2-2 to

finalize the procedure.

uTo configure a setup for PhotoGate and Smart Pulley

1. Perform the first three steps of the procedure under “To configure an EA-200 setup using

Setup Wizard” on page 2-2.

2. On the “Select Sensor” screen, select [VERN] - [P-Gate] - [Pulley].

•This causes an “Input Distance(m)” screen to appear.

•The distance you specify here is the distance the weight travels after it is released.

•Input a value in the range of 0.1 to 4 to specify the distance in meters.

3. Perform step 8 under “To configure an EA-200 setup using Setup Wizard” on page 2-2 to

finalize the procedure.

kOutputting the Waveform of a Function through the Speaker

Normally, the Setup Wizard helps you configure setups for sensors connected to the EA-200.

If you select [CASIO] - [SPEAKR] - [Y=f(x)] on the “Select Sensor” screen, however, it

configures the EA-200 to output the sound that corresponds to a function that you input and

graph on the calculator.

uTo configure a setup for speaker output

1. Connect the data communication cable (SB-62) to the communication port of the

calculator and the MASTER port of the EA-200.

2. Display the E-CON main menu (page 1-1), and then press 1(Setup EA-200).

•This displays the “Setup EA-200” submenu.

3. Press b(Wizard). This displays the Setup Wizard initial screen.

3. Use function keys 1through 4to select a Gate Status setting.

•Selecting a gate status causes a screen for specifying the number of samples to appear.

20021201

2-5

Using the Setup Wizard

5. Press wto advance to the View Window setting screen.

•The following settings are configured automatically: Ymin = –1.5 and Ymax = 1.5. Do not

change these settings.

6. Press wor ito advance to the graph function list.

7. In line “Y1”, input the function of the waveform for the sound you want to input.

•Note that the angle unit is always radians.

•Input a function where the value of “Y” is within the range of –1.5 to +1.5.

8. Press 6(DRAW) to graph the function.

•This graphs the function and displays a vertical cursor line as shown below. Use the

graph to specify the range that you want to output to the speaker.

9. Use the dand ecursor keys to move the cursor to the start point of the output, and

then press wto register it.

10.Use the dand ecursor keys to move the cursor to the end point of the output, and

then press wto register it.

•After you specify the start point and end point, a dialog box like the one shown below

appears on the display.

4. Select [CASIO] - f(SPEAKR) - c(Y=f(x)).

This displays a screen like the one shown below.

20021201

2-6

Using the Setup Wizard

11.Input a percent value for the output frequency value you want.

•Tooutput the original sound as-is, specify 100%. Toraise the original sound by one octave,

input a value of 200%. To lower the original sound by one octave, input a value of 50%.

12.After inputting an output frequency value, press w.

•This outputs the waveform between the start point and end point from the EA-200 speaker.

•If the sound you configured cannot be output for some reason, the message “Range

Error” will appear. Note that the supported output range is 200 to 4000Hz. If this

happens, press ito scroll back through the previous setting screens and change the

setup as required.

13.To terminate sound output, press the EA-200 [START/STOP] key.

•Pressing wafter terminating sound output returns to the output frequency dialog box in

step 11.

20021201

3Using Advanced Setup

Advanced Setup provides you with total control over a number of parameters that you can

adjust to configure the EA-200 setup that suits your particular needs.

The procedures in this section provide the general steps you should perform when using

Advanced Setup to configure an EA-200 setup, and to returns setup settings to their initial

default values. You can find details about individual settings and the options that are

available with each setting are provided by the explanations that start on page 3-2.

kAdvanced Setup Operations

uTo configure an EA-200 setup using Advanced Setup

The following procedure describes the general steps for using Advanced Setup. Refer to the

pages as noted for more information.

1. Display the E-CON2 main menu (page 1-1).

2. Press 1(SETUP). This displays the “Setup EA-200” submenu.

3. Press c(Advan). This displays the Advanced Setup menu.

4. If you want to configure a custom probe at this point, press f(Custom Probe). Next,

follow the steps under “To configure a custom probe setup” on page 4-1.

•You can also configure a custom probe during the procedure under “To configure Channel

Setup settings” on page 3-2.

•Custom probe configurations you have stored in memory can be selected using Channel

in step 5, below.

5. Use the Advanced Setup function keys described below to set other parameters.

•b(Channel) .... Displays a screen that shows the sensors that are currently

assigned to each channel (CH1, CH2, CH3, SONIC, Mic). You can

also use this dialog to change sensor assignments. See “Channel

Setup” on page 3-2 for more information.

•c(Sample) ..... Displays a screen for selecting the sampling mode, and for

specifying the sampling interval, the number of samples, and the

warm-up mode. When “Fast” is selected for “Mode”, this dialog box

also displays a setting for turning FFT (frequency characteristics)

graphing on and off. See “Sample Setup” on page 3-4 for more

information.

3-1

Using Advanced Setup

Advanced Setup Menu

20021201

3-2

Using Advanced Setup

•d(Trigger) ...... Displays a screen for configuring sampling start (trigger) conditions.

See “Trigger Setup” on page 3-6 for more information.

•e(Graph) ....... Displays a screen for configuring graph settings. See “Graph Setup”

on page 3-8 for more information.

•You can return the settings on the above setup screens (bthrough e) using the

procedure described under “To return setup parameters to their initial defaults”.

6. After you configure a setup, you can use the function key operations described below to

start sampling or perform other operations.

•1(START) ....Starts sampling using the setup (page 8-1).

•2(MULT) ......Starts MULTIMETER Mode sampling using the setup (page 5-1).

•3(MEM) .......Saves the setup (page 6-1).

•4(PRGM).....Converts the setup to a program (page 7-1).

•5(GRPH) .....Graphs data sampled by the EA-200, and provides tools for analyzing

graphs (page 10-1).

•6(ABOUT) ...Displays version information about the EA-200 unit that is currently

connected to the calculator.

uTo return setup parameters to their initial defaults

Perform the following procedure when you want to return the parameters of the setup in the

current setup memory area to their initial defaults.

1. While the Advanced Setup menu (page 3-1) is on the display, press g(Initialize).

2. In response to the confirmation message that appears, press wto initialize the setup.

•To clear the confirmation message without initializing the setup, press i.

kChannel Setup

The Channel Setup screen shows the sensors that are currently assigned to each channel

(CH1, CH2, CH3, SONIC, Mic).

uTo configure Channel Setup settings

1. While the Advanced Setup menu (page 3-1) is on the display, press b(Channel).

•This displays the Channel Setup screen.

Currently selected channel

Channel Setup Screen

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Casio Software Handbücher

Casio

Casio EMULATOR FX-ES Bedienungsanleitung

Casio

Casio Mobile Address Book (Version 2.0US) Bedienungsanleitung

Casio

Casio OS Update Bedienungsanleitung

Casio

Casio CW-100 - DISC TITLE PRINTER Bedienungsanleitung

Casio

Casio CASSIOPEIA Mobile Video Converter Bedienungsanleitung

Casio

Casio HANDHELD Bedienungsanleitung

Casio

Casio PHOTO LOADER Bedienungsanleitung

Casio

Casio USB MIDI DRIVER Bedienungsanleitung

Casio

Casio PHOTO LOADER - VER.3.0 FOR WINDOWS Bedienungsanleitung

Casio

Casio FA-123 Bedienungsanleitung

Casio

Casio E-Con EA-200 Bedienungsanleitung

Casio

Casio CLASSPAD Bedienungsanleitung

Casio

Casio Cassiopeia Pocket PC Bedienungsanleitung

Casio

Casio FA-B30 Bedienungsanleitung

Casio

Casio CELVIANO AP-220 Bedienungsanleitung

Casio

Casio Geometry Bedienungsanleitung

Casio

Casio fx-9860G AU PLUS Bedienungsanleitung

Casio

Casio DP-8000 Bedienungsanleitung

Casio

Casio SLIM FX-9860G Bedienungsanleitung

Casio

Casio Cassiopeia EM-500 Bedienungsanleitung

Casio

Casio Differential Equation Kurzanleitung

Casio

Casio Photo Loader Version 2.1 Bedienungsanleitung

Casio

Casio STAT 2 Bedienungsanleitung

Casio

Casio fx-9860G AU PLUS Bedienungsanleitung

Beliebte Software Handbücher anderer Marken

COMPRO

COMPRO COMPROFM Bedienungsanleitung

Muratec

Muratec OFFICEBRIDGE ONLINE Bedienungsanleitung

Oracle

Oracle Contact Center Anywhere 8.1 Bedienungsanleitung

Adobe

Adobe 65007312 - Photoshop Lightroom Handbuch

Avaya

Avaya NULL One-X for RIM Blackberry Bedienungsanleitung

HP ProLiant BL420c Bedienungsanleitung

PS Audio

PS Audio PowerPlay Betriebsanleitung

Brady

Brady LOCKOUT PRO 3.0 Service-Handbuch

Avaya

Avaya Interaction Center Bedienungsanleitung

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Handbuch

Novell

Novell GROUPWISE 8 - INTERNET AGENT Bedienungsanleitung

Oracle

Oracle Application 9i Bedienungsanleitung

Acer

Acer RDM Bedienungsanleitung

Canon

Canon Vixia HF21 Bedienungsanleitung

Canon

Canon ZR950 Bedienungsanleitung

Samsung

Samsung Auto Backup Bedienungsanleitung

Polycom

Polycom Vortex EF2201 Montage- und Bedienungsanleitung

Brocade Communications Systems

Brocade Communications Systems Brocade 8/12c Bedienungsanleitung