Cata PRO SILENCE Bedienungs- und Wartungshandbuch
EN
USE INSTRUCTIONS
HU
HASZNÁLATI UTASÍTÁSOK
60820635.10.11.2020.indb 160820635.10.11.2020.indb 1 1/3/21 14:271/3/21 14:27
60820635.10.11.2020.indb 260820635.10.11.2020.indb 2 1/3/21 14:271/3/21 14:27
EN
15
SAFETY
WARNING! Electric Shock Hazard Failure to follow this advice may result in
electric shock or death.
• Installation and electrical wiring must be completed by qualified person(s) in
accordance with all applicable codes and standards, including fire-rated cons-
truction.
• Always disconnect the appliance from the mains power supply before carr-
ying out any maintenance or repairs.
WARNING! Weight Hazard
Failure to follow this advice may result in damage or personal injury.
• The appliance is heavy. Please ensure adequate care is taken when installing
the appliance.
• Product weight: 5.8kg.
WARNING! Cut Hazard
Failure to use caution could result in injury.
• Take care: some edges are sharp.
• Wear gloves to protect against sharp edges.
WARNING!
To reduce the risk of fire, injury to persons or damage when using the applian-
ce, follow the important safety instructions listed. Read all this user guide befo-
re installing or using the appliance.
Servicing
Do not repair or replace any part of the appliance unless specifically recom-
mended in the installation or user guide. All other servicing should be made by
a service technician or qualified person.
Installation
• Please make this information is available for the person that is installing
the appliance.
60820635.10.11.2020.indb 1560820635.10.11.2020.indb 15 1/3/21 14:271/3/21 14:27
EN
16
• When cutting or drilling into wall or ceiling, do not damage electrical wiring
and other hidden utilities.
• This blower must be installed with a compatible Cata rangehood, failure to
do so can void your warranty.
• To reduce the risk of fire and electric shock, install this appliance only with
rangehood models specified.
• This external blower unit is intended to be installed on the roof only.
• To comply with electrical safety regulations, the rangehood which controls
the blower must be plugged into a socket near the appliance. The socket
must be accessible, or have an accessible isolating switch, to enable the
end user to isolate the appliance from the power for the purpose of internal
cleaning or maintenance.
• Always switch the power off before starting with the installation, servicing
or cleaning of the appliance.
• All ducting must comply with local requirements and building codes.
• Attention should be given to ensure that any applicable regulations concer-
ning the discharge of exhaust air are fulfilled.
• Ensure the supply cord is not exposed to heat, chemicals or sharp objects.
If the supply cord is damaged it must be replaced by a qualified person in
accordance with all applicable codes and standards, including fire-rated
construction.
• In order to avoid a hazard due to inadvertent resetting of the thermal cut-
out, this appliance must not be supplied through an external switching de-
vice, such as a timer, or connected to a circuit that is regularly switched on
and off by the utility.
60820635.10.11.2020.indb 1660820635.10.11.2020.indb 16 1/3/21 14:271/3/21 14:27
EN
17
General
• Remove all packaging and protections before use.
• This appliance incorporates an earth connection for functional purposes
only.
• To reduce risk of fire and to properly exhaust air, be sure to duct air outside
— Do not vent
• exhaust air into spaces within walls or ceilings or into attics, crawl spaces,
or garages.
• For information on environmental noise limit and conditions please contact
your local authority.
• The roof motor PRO SILENCE cannot be used in conjunction with a recircu-
lation rangehood.
INSTALLATION
- Must be installed with a 200mm diameter duct. If a different duct diameter is used it may
affect the motor performance by minimizing the airflow capacity and other values.
- The installation distance between the hood and the motor should be between 4 and 6
meters.A higher distance can decrease the airflow from the hood and a lower distance can
increase the noise level around the hood.
PARTS INCLUDED
- Keep all packing materials until the unit has been installed.
- Inspect the product to ensure there is no shipping damage. If any damage is detected
contact the dealer or retailer you bought the product from to report the damage.
External motor PRO SILENCE
Motor fixation support
150-200mm duct adapter
60820635.10.11.2020.indb 1760820635.10.11.2020.indb 17 1/3/21 14:271/3/21 14:27
EN
18
500mm diameter 150mm length PVC duct
200mm diameter 6m length flexible
ducting
PVC ducting fixation screws
Motor support fixation screws
Your external blower PRO SILENCE must be installed with a compatible rangehood. Refer
to the following list to know which are the available rangehoods to be installed with the
roof motor PRO SILENCE:
60820635.10.11.2020.indb 1860820635.10.11.2020.indb 18 1/3/21 14:271/3/21 14:27
EN
19
GRECO PRO SILENCE 90 BK 02184406 GRECO PRO SILENCE 90 WH 02184006
GRECO PRO SILENCE 90 GR 02184206 GLADIUS PRO SILENCE 900 XGBK 02181306
60820635.10.11.2020.indb 1960820635.10.11.2020.indb 19 1/3/21 14:271/3/21 14:27
EN
20
PRODUCT DIMENSIONS
A
C
D
GØ
EØ
FØ
BØ
DIMENSIONS mm
AOverall height 755
BOverall diameter 400
CHeight of blower unit 174
DHeight of external blower and backdraft damper 275
EOuter diameter of roof pipe 160
FDiameter of ducting outlet 200
GDiameter of grill 315
Length of power 6000
60820635.10.11.2020.indb 2060820635.10.11.2020.indb 20 1/3/21 14:271/3/21 14:27
EN
21
ELECTRICAL REQUIREMENTS
Rating plate
location
Before starting with the PRO SILENCE roof blower installation to the power supply, ensure
that the voltage and frequency from the installation location match with the values mentio-
ned on the rating plate of the product.
Model Frequency Voltage
PRO SILENCE 50Hz 230V
Do not cursh or bend the ducting
60820635.10.11.2020.indb 2160820635.10.11.2020.indb 21 1/3/21 14:271/3/21 14:27
EN
22
INSTALLATION
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other
hidden utilities.
WARNING! Failure to install the screws or fixing device in accordance with these
instructions may result in electrical hazards.
Create a hole in the roof to introduce the
PVC pipe.
Secure the PVC roof pipe to an internal
house structure that is strong enough to
support the complete system. Ensure the
pipe is aligned with the vertical axis.
50mm
Seal the pipe with appropriate roof
sealing kit to avoid any leakage. Ensure the
pipe protrudes a
minimum of 50mm from the seal.
Install the back draft damper assembly
to the motor unit using the 12mm
sheet metal screws (4) provided.
Pass the power cord and plug through
the slot in the roof pipe and pull from the
slot in the other side.
60820635.10.11.2020.indb 2260820635.10.11.2020.indb 22 1/3/21 14:271/3/21 14:27
Inhaltsverzeichnis
Sprachen:
Andere Cata Dunstabzugshaube Handbücher
Cata
Cata Isla Gamma Referenzhandbuch
Cata
Cata IHD60SV Technisches Datenblatt
Cata
Cata GCHEP60SS Bedienungsanleitung
Cata
Cata F-2050 WH Benutzerhandbuch
Cata
Cata GT-Plus Sicherheitsleitfaden
Cata
Cata TF6600 Benutzerhandbuch
Cata
Cata CHK60 Bedienungsanleitung
Cata
Cata VALTO Kurzanleitung
Cata
Cata PROFESSIONAL 750 Bedienungsanleitung
Cata
Cata GT-Plus Referenzhandbuch
Cata
Cata TFB-5060 Kurzanleitung
Cata
Cata GC Dual A 45 XGWH/B Referenzhandbuch
Cata
Cata TF-7600-WH Benutzerhandbuch
Cata
Cata F-2060 Bedienungsanleitung
Cata
Cata V6000WH/A Kurzanleitung
Cata
Cata ISCG90SS Bedienungsanleitung
Cata
Cata TFH 6430 X Benutzerhandbuch
Cata
Cata ASOMA 600 Kurzanleitung
Cata
Cata TFH6630 Kurzanleitung
Cata
Cata ALPHA6 Bedienungsanleitung
