CBM CBM-710 Bedienungsanleitung

CBM-710/720/730/750 User’s Manual

CITIZEN

Declaration of Conformity

Manufacturer’s Name : Japan CBM Corporation

Manufacturer’s Address: CBM Bldg., 5-68-10, Nakano, Nakano-ku

Tokyo, 164-0001, Japan

Declare the Product

Product Name: Dot Matrix Printer

Model Number(s): CBM-710,720,750 Series

(CBM-710R, CBM-710P, CBM-720R, CBM-720P,

CBM-750R, CBM-750P)

(S.No.0090001 ~ )

Conform to the following Standards:

LVD: : EN60950 : A4:1997

EMC: : EN55022 : 1998 Class A

: EN61000-3-2 : 1995+A1:1998+A2:1998

: EN61000-3-3 : 1996

: EN55024 : 1998

: EN61000-4-2 : 1995 ±4KV CD, ±8KV AD

: EN61000-4-3 : 1996 4.5V/m, 80MH-1000MHz AM 1KHz 80%

: EN61000-4-4 : 1995 ±1.0KV (AC Mains), ±0.5KV (Signal Lines)

: EN61000-4-5 : 1996 ±1KV (Normal mode), ±2KV (Cmmon mode)

: EN61000-4-6 : 1996 3V, 0.15MHz-80MHz AM 1KHz 80%

: EN61000-4-8 : 1993 50Hz, 3A/m

: EN61000-4-11 : 1994 0%, 5000ms/ 70%, 500ms/ 0%, 10ms

Supplementary Information

“The product complies with the requirements of the Low Voltage Directive 73/23/EEC, 93/68/EEC and

the EMC Directive 89/336/EEC, 92/31/EEC, 93/68EEC”

Place Tokyo, Japan Signature:

Date September, 2000

Full Name : Mikio Moriya

Position : General Manager

R & D Department

European Contact :

Norco Declaration AB

Box 7146 S-250 07 Helsingborg, Sweden

WARNING: This is a Class A products. In a domestic environment this product may cause radio interference in

which case the user may be required to take adequate measures.

This declaration is applied only for 230V model.

CBM-710/720/730/750 User’s Manual

CITIZEN

IMPORTANT SAFETY INSTRUCTIONS

• Read all of these instructions and save them for future reference.

• Follow all warnings and instructions marked on the product.

• Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners.

Use a damp cloth for cleaning.

• Do not use this product near water.

• Do not place this product on an unstable cart, stand or table. The product may fall, causing

serious damage to the product.

• Slots and openings on the back or bottom of the case are provided for ventilation. To ensure

reliable operation of the product and to protect it from overheating, do not block or cover these

openings. The openings should never be blocked by placing the product on a bed, sofa, rug of

other similar surface. This product should never be placed near or over a radiator or heater. This

product should not be placed in an built-in installation unless proper ventilation is provided.

• This product should be operated from the type of power source indicated on the marking label. If

you re not sure of the type of power available, consult your dealer or local power company.

• Do not allow anything to rest on the power cord. Do not place this product where the cord will be

walked on.

• If an extension cord is used with this product, make sure that the total of the ampere ratings of the

products plugged into the extension cord does not exceed the extension cord ampere rating. Also,

make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes.

• Never push objects of any kind into this product through cabinet slots as they may touch

dangerous voltage points or short out parts that could result in a risk of fire or electric shock.

Never spill liquid of any kind on the product.

• Except as explained elsewhere in this manual, do not attempt to service this product by yourself.

Opening and removing the covers that are marked “Do Not Remove” may expose you to

dangerous voltage points or other risks. Refer all servicing on those compartments to service

personnel.

• Unplug this product from the wall outlet and refer servicing to qualified service personnel under the

following conditions:

A. When the power cord or plug is damaged or frayed.

B. If liquid has been spilled into the product.

C. If the product has been exposed to rain or water.

D. If the product does not operate normally when the operating instructions are followed. Adjust

only those controls that are covered be the operating instructions since improper adjustment of

other controls may result in damage and will often require extensive work by a qualified

technician to restore the product to normal operation.

E. If the product has been dropped or the cabinet has been damaged.

F. If the product exhibits a distinct change in performance, indicating a need for service.

CBM-710/720/730/750 User’s Manual

CITIZEN

IMPORTANT:This equipment generates, uses, and can radiate radio frequency energy and if not

installed and used in accordance with the instruction manual, may cause interference to radio

communications. It has been tested and found to comply with the limits for a Class A computing

device pursuant to Subpart J of Part 15 off FCC Rules, which are designed to provide reasonable

protection against such interference when operated in a commercial environment. Operation of this

equipment in a residential area is likely to cause interference, in which case the user at his own

expense will be required to take whatever measures may be necessary to correct the interference.

CAUTION: Use shielded cable for this equipment.

Sicherheitshinweis

Die Steckdose zum Anschluß dieses Druckers muß nahe dem Grät angebracht und leicht zugänglich

sein.

For Uses in Canada

This digital apparatus does not exceed the class a limits for radio noise emissions from digital,

apparatus, as set out in the radio interference regulations of the Canadian department of

communications.

Pour L’utilisateurs Canadiens

Cet appareil numerique ne depasse pas les limites de caregorie a pour les emissions de bruit radio

emanant d’appareils numeriques, tel que prévu dans les reglements sur l’interference radio du

department Canadien des communications.

CBM-710/720/730/750 User’s Manual

CITIZEN

CONTENTS

1. INTRODUCTION ................................................................................................................................................. 1

1.1 Features ............................................................................................................................................ 1

1.2 Accessories....................................................................................................................................... 1

2. TYPE CLASSIFICATIONS ................................................................................................................................. 2

3. SPECIFICATIONS ............................................................................................................................................... 3

3.1 General Specifications...................................................................................................................... 3

3.2 Print Format ..................................................................................................................................... 5

3.3 Paper Specifications ......................................................................................................................... 5

4. BLOCK DIAGRAM.............................................................................................................................................. 6

5. EXTERNAL APPEARANCE AND PARTS DESCRIPTIONS ........................................................................ 7

5.1 CBM-710 External Appearance ....................................................................................................... 7

5.2 CBM-720 External Appearance ....................................................................................................... 8

5.3 CBM-730 External Appearance ....................................................................................................... 9

5.4 CBM-750 External Appearance .....................................................................................................10

5. 5 Part Descriptions ............................................................................................................................ 11

6. OPERATION ....................................................................................................................................................... 12

6. 1 Setting and Removing the Paper and Ribbon Covers .................................................................... 12

6.2 Opening and Closing the Cutter Unit (CBM-720. CBM-750)....................................................... 13

6.3 Installing the Cassette Ribbon........................................................................................................ 14

6.4 Installing and Changing the Paper.................................................................................................. 15

6.5 Self Print Function ......................................................................................................................... 18

6.6 Paper End Detector......................................................................................................................... 18

6.7 Installation of the CBM-750 .......................................................................................................... 19

7. INPUT BUFFER BACK-UP FUNCTION......................................................................................................... 20

7.1 Input Buffer Back-up ..................................................................................................................... 20

7.2 Clearing the Input Buffer ............................................................................................................... 20

8. PARALLEL INTERFACE ................................................................................................................................. 21

8.1 Specifications ................................................................................................................................. 21

8.2 Connector Pin Assignment............................................................................................................. 21

8.3 Description of Input/Output Signals............................................................................................... 22

9. SERIAL INTERFACE........................................................................................................................................ 25

9.1 Specifications ................................................................................................................................. 25

9.2 Connector Pin Assignment............................................................................................................. 26

9.3 Description of Input/Output Signals............................................................................................... 27

10. FUNCTION SELECTION............................................................................................................................... 32

11. PRINT CONTROL FUNCTIONS ................................................................................................................... 35

11.1 Control Codes................................................................................................................................. 35

11.2 Input Data Formats......................................................................................................................... 36

12. CHARACTER CODE TABLES ...................................................................................................................... 44

CBM-710/720/730/750 User’s Manual

CITIZEN

13. MAINTENANCE............................................................................................................................................... 46

13.1 Maintenance Procedures ................................................................................................................ 46

14. EXTERNAL DIMENSIONS............................................................................................................................. 47

14.1 CBM-710........................................................................................................................................ 47

14.2 CBM-720........................................................................................................................................ 48

14.3 Paper Winder Unit AW-2............................................................................................................... 49

14.4 CBM-730........................................................................................................................................ 50

14.5 CBM-750........................................................................................................................................ 51

<<< GERMAN >>>

3. TECHNISCHE DATEN...................................................................................................................................... 53

3.1 Allgemeine Daten........................................................................................................................... 53

3.2 Druckformat ................................................................................................................................... 55

3.3 Papierdaten..................................................................................................................................... 55

5. AUSSENANSICHT UND BESCHREIBUNG DER TEILE ............................................................................ 56

5.2 CBM-720 Außenansicht................................................................................................................. 56

5.5 Beschreibung der Teile................................................................................................................... 57

6. BETRIEB.............................................................................................................................................................. 58

6.1 Anbringen und Abnehmen der Papierfach- und Farbbandabdeckungen........................................ 58

6.2 Öffnen und Schließen des Papierschneiders (CBM-720, CBM-750)............................................. 59

6.3 Einsetzen der Farbbandkassette...................................................................................................... 60

6.4 Einsetzen und Wechseln des Papiers.............................................................................................. 61

8. PARALLELE SCHNITTSTELLE..................................................................................................................... 62

8.1 Technische Daten........................................................................................................................... 62

8.2 Stiftbelegung .................................................................................................................................. 62

8.3 Beschreibung der Ein-/Ausgangssignale........................................................................................ 63

9. SERIELLE SCHNITTSTELLE......................................................................................................................... 66

9.1 Technische Daten........................................................................................................................... 66

9.2 Stiftbelegung .................................................................................................................................. 67

9.3 Beschreibung der Ein-/Ausgangssignale........................................................................................ 68

10. FUNKTIONSWAHL......................................................................................................................................... 71

11. DRUCKSTEUERFUNKTIONEN.................................................................................................................... 74

11.1 Steuercodes .................................................................................................................................... 74

ATTENTION: Please RESET the printer to clear the input buffer before getting started. (Ref. to Chapter 7-2)

CBM-710/720/730/750 User’s Manual

1 CITIZEN

1. INTRODUCTION

The CBM-710, CBM-720, CBM-730 and CBM-750 are dot impact printers which can be utilized for a wide

range of applications, such as data communications terminals, ECR terminals and kitchen printers. High speed

performance is made possible by a bidirectional printing system and, since these printers are compact, lightweight

and equipped with an abundance of functions, they can be easily employed for a variety of different tasks.

The CBM-720 and CBM-750 have a built-in automatic cutter capable of performing a partial cut (three

connecting points remaining) or full cut (one connecting point remaining), which can be controlled through printer

command codes.

Before using your printer, please read this manual carefully to be certain you have an adequate understanding of

its operation.

1. 1 Features

(1) Desktop compact dot impact printer

(2) High Speed Printing (Bidirectional Printing System)

(3) Built-in Auto Cutter (Partial Cut/Full Cut) (CBM-720 and CBM-750)

(4) Black & Red 2 Color Printing or All Black Printing

(5) Paper End Detection Function

(6) Input Buffer Back-up Function

(7) Low Power Consumption

1.2 Accessories

Paper Roll (1 pc) - CBM-710, CBM-720, CBM-750

Cassette Ribbon (1 pc)

Base Stoppers (2 pcs) - CBM-750

Hanger (1 pc) - CBM-750

Screws (2 pcs) - CBM-750

CBM-710/720/730/750 User’s Manual

2 CITIZEN

2. TYPE CLASSIFICATIONS

Printer types are classified according to the system shown below.

CBM-710

100

115

230

–

CBM-720 ↑↑↑↑↑↑–

CBM-730 ↑↑↑↑↑↑–

CBM-750 ↑↑↑↑↑↑–

CBM-710 – 23 R J 100 G – B – V

The exclusive paper winder mechanism (Model AW-2) is available separately. This mechanism can be mounted on

any of the printer types, except CBM-710, 720.

Model

CBM-710

CBM-720

CBM-730

CBM-750

Column capacity

23: 23 columns

28: 28 columns

40: 40 columns

Interface

P : Parallel type P

R : Serial type R

RS-232C

20mA Current loop

X : RS422A

Character set

J : Japanese

F : International

Validation Function

V : With Validation

No symbol : Without Validation

Memory Back-up

B : With Back-up

N : Without Back-up

Mode

G : Graphic

C : Character

I : Character (Type II)

Power Source

100 : AC 100V

115 : AC 115V

230 : AC 230V

CBM-710/720/730/750 User’s Manual

3 CITIZEN

3. SPECIFICATIONS

3.1 General Specifications

Item CBM-710, 730 CBM-720, 750

1 Print Method Bidirectional serial dot impact method

2 Character composition 7 ×7 dots (1ncl. half-dots)

3 Character number per line

23 columns: 230 dot/line

28 columns: 280 dot/line

40 columns: 360 dot/line

4 Print speed

23 columns: approx.4.0 line/sec.

28 columns: approx. 3.5 line/sec.

40 columns: approx. 3.0 line/sec.

5 Character size

23 columns: 1.8(W) ×2.4 (H) mm

28 columns: 1.5(W) ×2.4 (H) mm

40 columns: 1.36(W) ×2.4 (H) mm

6 Line pitch C: Character Type: 4.23 mm (1/6 inch)

G: Graphic Type: 2.82 mm (1/9 inch)

7 Paper size

Friction Type: 76.0 ~ 0.5 mm (W) ×80 mm (Dia.)

3.0 inch (W) ×3.0 inch (Dia.)

Pin Wheel Type: 76 ~ 89 mm (W)

3 ~ 3.5 inch (W)

8 Interface

P: Parallel interface (8 Bit)

R: Serial interface (RS232C, 20 mA current loop)

X: Serial interface (RS422A)*2

9 Input buffer 7K bytes or 2 line buffer

10 Input buffer back-up

N Type: Without back-up.

B Type: Duration of back-up: More than 100 hours.

(But after 10 minutes operation)

11 Paper end detection When paper is near the end, the buzzer actuates and print operation is

interrupted, or PE signal is issued.

CBM-710/720/730/750 User’s Manual

4 CITIZEN

Item CBM-710, 730 CBM-720, 750

12 Validation Print Available only for V-Type (1 line print)

13 Auto cutter Without cutter With cutter Partial cut/Full cut*3

14 Cassette ribbon Two color (Black and Red) print IR-61R/B*4

15 Paper winder Model AW-2 available as option

16 Power voltage*5

100V ±10%, 50/60 Hz (For Japan)

115V ±10%, 60 Hz (For United States)

230V ±10%, 50/60Hz (For Europe)

17 Power consump. Approx. 30W

18 Operation temp. & humidity 5° to 35°C / 41° to 95°F

10% to 85% RH

19 Storage temp. -20° to 70°C

20 Net weight Approx. 3.1 kg (710)

Approx. 3.3 kg (730)

Approx. 3.3 kg (720)

Approx. 3.6 kg (750)

21 External dimensions Refer to Section 14.

Notes: * l Paper weight of 45 kg refers to 1,000 sheets of 788 ×1,091 mm.

*2 RS-422A interface specifications are not included in this manual

1. With the RS422A type interface, only a one line input buffer can be selected.

2. However, when the input buffer is set for two lines, back-up of graphic data is not possible.

*3 Partial cut is three connecting points remaining. Full cut is one connecting point remaining.

*4 Single color print ribbon is available as option.

Black print: IR-61B

Purple print: IR-61P

V Type: Use only single color print ribbon.

*5 Power voltage setting is performed at the factory.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere CBM Drucker Handbücher

CBM

CBM CMP-10 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung