CC&C WL1200 Bedienungsanleitung
User’s Guide
Wireless LAN USB Dongle
11 Mbps
Version 2.0
2
Table of Contents
Information to User……………………………….... 3
1Introduction………………………..………………... 5
2Wireless LAN basics……………………..………… 6
3Windows Installation……………………………….. 7
3.1 Installation and Configuration Procedures… 8
3.2 Configuration Utility…………………………... 15
4Technical Specifications…………………………… 22
Glossary…………………………………………….. 23
Product names mentioned herein may be trademarks and/or registered trademarks of their respective companies.
3
INFORMATION TO USER
FCC INFORMATION
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20centimeters between the radiator and your body.
The equipment has been tested and found to comply with the limits for a Class B
Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction, may cause harmful interference
to radio communication. However, there is no grantee that interference will not occur
in a particular installation. If this equipment dose cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
--Consult the dealer or an experienced radio or television technician for help.
Notice: The Part 15 radio device operates on a non-interference basis with other
devices operating at this frequency. Any changes or modification not
expressly approved by the party responsible could void the user’s authority to
operate the device.
4
REGULATORY INFORMATION
The Wireless LAN USB Dongle must be installed and used in strict accordance with
the manufacturer’s instructions. This device complies with the following radio
frequency and safety standards.
USA -Federal Communications Commission (FCC)
This device complies with Part 15 of FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference that may cause undesired operation.
Europe -R&TTE Directive
This device complies ./with the specifications listed below
• ETS 300 328 Technical requirements for Radio equipment.
• ETS 301 489 -1 & -17 General EMC requirements for Radio equipment.
• EN 60950 Safety Requirements for Radio equipment
5
1. Introduction
Thank you for purchasing your Wireless Local Area Net (WLAN) USB
Dnogle. You are about to install a networking system that is not only fast
and powerful, but also easy to set up and simple to maintain. In a short time
you and those in your network will be able to share a local printer and files,
access the Internet, and roam about the office wire-free.
Using radio frequency (RF) technology, WLANs transmit and receive
data over the air, minimizing the need for wired connections. Thus, WLANs
combine data connectivity with user mobility, and, through simplified
configuration, enable movable LANs.
This wireless networking solution has been designed for both large and
small businesses, and it is scalable so that you can easily add more users
and new network features as your business grows.
This manual will assist you in the installing WLAN USB Dongle.
6
2. Wireless LAN basics
Wireless LAN network defined by IEEE 802.11b standard committee could be
configured as:
•
Ad Hoc wireless LAN or
•
Infrastructure wireless LAN
Ad Hoc network is a group of notebooks with WLAN PC cards or USB dongles
called a BSS (Basic Service Set). These notebooks use their WLAN PC cards or USB
dongles to communicate with each other, and notebooks can not connect to the
Internet.
Figure 2-1 Ad Hoc wireless network
The most obvious differentiation between Infrastructure wireless network and
Ad Hoc wireless network is that the notebooks in Infrastructure wireless network can
make use of the resource in the Internet through Access Point.
STA 3
STA 1
STA 2
Access Point
Internet
Figure 2-2 Infrastructure wireless network
To set up your notebook’s network as the type of “Ad Hoc” or “Infrastructure”
wireless network depends completely on your requirement. Generally, if your network
environment has an Access Point, we recommend that you set it as “Infrastructure”
to connect to theInternet.
STA 1
STA 2
STA 3
7
3. Windows Installation
The following section will assist you to install Wireless LAN USB successfully. You will
first install software (driver) and then connect the Wireless LAN USB, and finally set
the network properties to accommodate resource sharing and select the type of
wireless network that you wish to install. The Wireless LAN can easily be installed and
used, without bothering to connect cables for keeping your computer to use network
resources, as in case of wired LAN.
Before You Start
Here are some steps you will perform in establishing your wireless network
connection:
•Install the Access Point at first. AP is needed in case of infrastructure
network mode.
•Install the software using the Installation CD ROM
•Install the Wireless LAN USB Dongle
•Install the network protocol(s) required to communicate on your network.
Most likely you will need the TCP/IP protocol.
8
3.1 Installation and Configuration Procedures
Under Windows 98 SE
Please follow the following steps one by one in order to install the WLAN USB
Dongle successfully.
Step 1. Power on your computer and allow Windows 98 SE to load fully. Be sure
that there is no USB dongle is connected to computer yet. Insert the given
documentation CD and then double click the MY Computer icon on your
desktop. In my computer window, double click the CD Drive icon. Choose
WLAN USB Dongle folder and double click setup to execute Setup.exe. It
opens the InstallShield Wizard dialog box as shown next page.
9
Click Next to continue.
Step 2. Software License Agreement, click Yes to accept.
10
Step 3. Select Adapter Type. Please select Application & USB Drivers then click
Next.
Step 4. Click Next to search for alreadyinstalled components.
Inhaltsverzeichnis
Andere CC&C Computerhardware Handbücher
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
