CDI 511-4017 Leitfaden
Installation and Troubleshooting Guide
All rights reserved. Reproduction or use of content, in any manner, without express written permission by CDI Electronics, Inc., is prohibited
.
CDI Electronics •353 James Record Road SW •Huntsville, AL 35824
Web Support: www.cdielectronics.com •Tech Support: 1-866-423-4832 •Order Parts: 1-800-467-3371
All rights reserved. Reproduction or use of content, in any manner, without express written permission by CDI Electronics, Inc., is prohibited.
Rev A •7/22/13 Page - 1 of 1 QF-319
CDI P/N: 511-4017 Optical Sensor Tester/Timing Tool
NOTICE: This product is intended for use by professional marine mechanics. CDI Electronics cannot be held liable for injury or damage
resulting from improper use, abuse, neglect, or misuse of this product.
The optical sensor works by shining infrared light through the windows in the timing wheel to photo sensors on the other
side. Infrared light is also used in most TV type remote controls and is not visible to the human eye. As the sensor is light
sensitive, avoid exposure to bright sunlight when the timing wheel cover is removed and never point a timing light at the
sensor.
Ensure there is no blockage or cracks in the timing wheel and no obstructions or liquid in the sensor. When cleaning the
sensor, do not use any solvents as these can damage the sensor’s lenses. Soap and water is recommended.
A) Remove the regulator cover and disconnect the timing sensor plug.
B) Attach the 511-4017 Sensor Tester to the timing sensor and a 12V source.
C) The GREEN “Sensor Power” indicator should light indicating that the sensor’s light emitters are working. If this
indicator does not light the sensor is bad.
D) Crank the engine briefly while observing the RED “Sync” and “Cylinder” indicators. There should be one Sync and 7
Cylinder pulses per engine revolution for a V6, one Sync and 5 Cylinder pulses for a V4. If either of these indicators
fails to flash or stays on continuously the sensor is bad.
When using the Sensor Tester/Timing Tool for adjusting static timing, switch the “Tone” function on. The tester will sound
a loud tone whenever the “Cylinder” indicator is on allowing you to set the timing while looking at the timing pointer instead
of the tester.
OPERATING
Set the timing according to the service manual for your engine. You must perform the Sync & Link procedure in order to
have the engine perform normally.
ENGINE IDLE Timing WOT Timing
90/115/150/175 4-6 Deg ATDC 19-20 Deg BTDC
100/105/105WR/115JPL 4-6 Deg ATDC 22 Deg BTDC
NOTE: Adjust the idle timing to adjust the idle speed.
ON indicates short
sensor eye sees light
ON indicates tall
sensor eye sees light
Controls audible
cylinder tone
ON indicates path
through both sensor
emitters is good
One Flash per
revolution
7 Flashes per
revolution
(# of cylinders + 1)
Inhaltsverzeichnis
Andere CDI Prüfgeräte Handbücher
Beliebte Prüfgeräte Handbücher anderer Marken
SMART
SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung
Agilent Technologies
Agilent Technologies BERT Serial Bedienungsanleitung
Agilent Technologies
Agilent Technologies N3280A Bedienungsanleitung
Vernier
Vernier Go Direct Voltage Bedienungsanleitung
Lifeloc
Lifeloc R.A.D.A.R. Bedienungsanleitung
Fluke
Fluke T5-600 Bedienungs- und Montageanleitung
PCB Piezotronics
PCB Piezotronics 8159-0112A Bedienungsanleitung
BW Technologies
BW Technologies MicroDock II Bedienungsanleitung
Sun Nuclear
Sun Nuclear 1027 Bedienungsanleitung
Biomark
Biomark HPR LITE READER Bedienungsanleitung
Hioki
Hioki 3169-20 Bedienungsanleitung
Ashcroft
Ashcroft ATE-100 Bedienungsanleitung