Celsi B-1036317 Bedienungsanleitung

22” & 33” Ultiflame Electric Fire

Model No’s:

B-1036317, & B-1036318

CEU 22RE-RGB & CEU 33RE-RGB

Packing Checklist - Pack 1 of 1

Electric Fire

Remote Control Handset*

Black Chippings Set

Instruction Manual

Log Set

Log Layout Instruction Sheet

*THIS PRODUCT REQUIRES 3 X AAA BATTERIES FOR USE IN THE HANDSET (NOT SUPP IED)

IMPORTANT

P EASE READ THESE INSTRUCTIONS CAREFU Y BEFORE

INSTA ATION AND USE OF THIS E ECTRIC FIRE AND

RETAIN FOR FUTURE REFERENCE.

This appliance is not intended for use by persons (including children) with reduced

physical, sensory or learning disabilities, or lack of experience and knowledge, unless

given supervision or instruction concerning use of the appliance by a person responsible

for their safety.

If the supply cord is damaged, it must be replaced by the manufacturer, its

service agent or similarly qualified persons in order to avoid a hazard.

IMPORTANT SAFETY ADVICE

WHEN USING AN E ECTRICA APP IANCE, BASIC PRECAUTIONS SHOU D

A WAYS BE FO OWED TO REDUCE THE RISK OF FIRE, E ECTRIC SHOCK AND

INJURY TO PERSONS, INC UDING THE FO OWING IMPORTANT SAFETY ADVICE.

DO NOT cover the heater, to avoid overheating of the product.

DO NOT leave the heater unattended while it is in use. Always turn the fire to the OFF

position and switch off at the mains socket when not in use.

DO NOT leave children unsupervised whilst the fire is switched on.

DO NOT operate this fire with a damaged cord or plug, or after the fire

malfunctions, has been dropped or damaged in any way. Contact the manufacturer.

DO NOT install a timer switch to operate the fire.

DO NOT insert or allow objects to enter any ventilation or exhaust openings on the

fire. To prevent a possible fire do not block air intakes or exhaust openings in any manner.

DO NOT place this fire near flammable materials, surfaces or substances, as there may be a

risk of fire. eep flammable materials, surfaces or substances at least 1 metre away from the

front of the product.

DO NOT switch on the fire if volatile vapours are present in the room.

DO NOT use this fire in any areas where petrol, paint or other flammable liquids are stored

e.g. a garage or a workshop as the fire contains components capable of

producing a spark.

DO NOT touch any hot surfaces such as the heater vent when the heater is in use to avoid

burns and personal injury.

DO NOT install the heater immediately below an electrical socket outlet.

DO NOT use outdoors.

CAUTION - Some parts of this product can become hot during use and cause burns.

Particular attention has to be given where children and vulnerable people are present.

This fire is for household use only.

Page 1 of 30

PRODUCT TECHNICA DATA SHEET

Supplier Name / Trademark Celsi

Supplier Model Identifier B-1036317 Ultiflame 22”

B-1036318 Ultiflame 33”

Voltage 230v AC 50HZ

Fuse 13 Amp

Nominal Heat Output (Measured) 1.6kW

Minimum Heat Output (Indicative) 0.8kW

Maximum Continuous Heat Output 1.6kW

Auxilliary Electrical Consumption 0.016kW

at Nominal Heat Output

Auxilliary Electrical Consumption 0.016kW

at Minimum Heat Output

Auxilliary Electrical Consumption 0.0005kW

at Standby Mode

Type of Heat Output / RTC* With electronic room temperature control

plus 7 day timer.

Other Control Options With adaptive start control

Manufacturers Name and Address BFM Europe Ltd. Gordon Banks Drive,

Trentham Lakes, Stoke-on-Trent,

Staffordshire, ST4 4TJ

*RTC = Room Temperature Control Tel: 01782 339000

Fire Dimensions - Fig. 1

Ultiflame 22” Ultiflame 33”

Page 2 of 30

Unpacking

Remove and discard the plastic bag.

Be responsible when handling the packing materials.

eep the original packaging for future transportation and/or storage.

Check all accessories are removed from the packaging before storing it away for future use.

KEEP P ASTIC BAGS AWAY FROM CHI DREN!

Choosing a Suitable ocation

This electric fire is designed to be fitted within an existing brick / masonry chimney breast

which must be dry with the chimney capped off using a suitable chimney cap.

The appliance must be kept away from any source of damp or moist conditions. Avoid any

close contact with water.

Important Notice: To reduce heat losses and to prevent any chimney up draught affecting

the operation of your fire we recommend that the chimney is blocked off.

The chimney breast, wall or fireplace must be of sound construction and all fixings used

must be suitable for the type of wall. If there is any doubt regarding the suitability of the in-

stallation site please contact your supplier.

From the front of the fire ensure that there is a minimum clearance of 50mm between any

non-combustible materials. For combustible material clearances please consult with the man-

ufacturer.

The fire can be connected direct or plugged into a mains socket which can be sited on the

right hand side of the fire.

Ensure that the plug socket-outlet connection for this appliance is accessible. It MUST be

readily accessible for easy electrical isolation in the event of servicing and replacing compo-

nents etc. This appliance MUST NOT be located immediately below an electrical socket-out-

let.

Please refer to the relevant installation instructions applicable to the model fire purchased.

Installation must be carried out by a qualified and competent person.

The opening sizes required to install the fires are

Ultiflame 22” Ultiflame 33”

Height = 650mm Height = 605mm

Width = 610mm Width = 890mm

Depth = 185mm Depth = 185mm

Page 3 of 30

Connect the appliance to single-phase AC supply of the voltage specified on the rating plate.

Should the fire be connected directly into the mains supply, then a fused switched spur with

a 13 amp fuse must be fitted. It is imperative that the power supply is capable of handling a

load of 2000 watts (2kw). This appliance must be earthed. Allow sufficient flex to enable the

fire to be removed from the wall. Do not use an extension lead

IMPORTANT NOTE: Models which have LED downlights included in the suite / surround

will require an additional mains supply. If wired directly into the mains supply, then a fused

switched spur with a 3 amp fuse must be fitted ensuring that the plug socket-outlet

connection is accessible. It MUST be readily accessible for easy electrical isolation in the

event of servicing and replacing components etc.

Always ensure that all electrical work complies with the relevant Building Regulations and the

Electrical Code of Practice. All electrical work should be carried out by a qualified electrician.

Ultiflame 22” & 33” Wall Mounting

The base of the fire opening must be solid, level and firmly fixed to safely support the weight

of the fire.

Fig. 2

The fire is held in place using 4 suitable screws and fasteners in the 4 fixing holes on the

sides of the appliance as shown above in figure 2.

A false studded chimney breast can be built with a plastered finish to encase the fire

The chimney wall can now be finished with plasterboard or an alternative facing material

which terminates at the facing trim.

The fire can be fitted direct into the chimney breast and plastered flush up to the facing trim

Page 4 of 30

4 x fixing holes

Fig. 3

Ultiflame 22” & 33” with Trim option

Installation is the same principle as wall mounting but the fire is screwed to the plastered

wall to ensure that the facing trims protrude from the fire. For fitting of the trim please refer

to the instructions included with the trim.

Page 5 of 30

Rennes, Avignon & ille Models (22”)

Fireplace opening for Pablo, Boticelli & Angelo Surrounds, see figures 4, 5 & 6

When fitting this fire into a surround the fireplace opening needs to be prepared at differing

heights dependent upon which surround type is to be installed.

Fig. 4 - Pablo Surround

Fire opening to be 146mm from floor level

Fig. 5 - Boticelli Surround

Fire opening to be 146mm from floor level

Fig. 6 - Angelo Surround

Fire opening to be 172mm from floor level

Page 6 of 30

INSTA ING THE “PAB O” SURROUND

1. Unpack the surround from the wooden crate, check all parts are present and carefully

store the components.

Contents of Pablo surround:-

1 off hearth panel

1 off R/H leg

1 off L/H leg

1 off R/H infill section

1 off L/H infill section

1 off bottom infill section

1 off shelf

1 off stub hearth

Fig. 7

2. The underside of the hearth should be painted with a weak PVA (8 parts water to 1 part

PVA). This will prevent staining penetrating through the stone. The hearth must be

centred to the opening. If the fireplace is to be installed on a chimney breast ensure that

the opening is also centred to the chimney breast. It is essential that the hearth is

completely level. The hearth must be bedded down on bonding or an equivalent

material. Avoid cement based products and ensure the hearth is firmly fitted and well

supported. Allow the bedding material to set before any weight is placed onto the

hearth. Wipe off any surplus bonding material with a wet sponge.

3. Fit bottom section to hearth, ensure it is central before fixing with a suitable mastic

adhesive.

4. Fit brackets to top of legs, offer leg up to wall and mark position of fixing hole on wall,

use shelf to ensure legs are correctly spaced / positioned. Remove shelf then cover

hearth with dust sheet and drill the fixing holes. Remove the brackets from the legs, fix

the side infills into place with suitable adhesive and secure the leg fixing brackets only to

the wall. Fit legs to brackets that have been securely attached to the wall with fixings as

detailed in Point 5.

5. Assess the chimney breast onto which the fire is to be installed and ensure that it is of

sound construction and suitable for supporting the weight of the surround. Fixings used

to secure the leg brackets to the masonry of the chimney breast shall be of expansive

stainless steel or galvanised steel type masonry fixings for dense concrete blockwork or

brickwork. Where fixings are located into light weight blockwork or friable aggregate

blocks, the fixings shall be of the resin anchor type.

Page 7 of 30

6. Fix the top infill and shelf infill into place again with suitable mastic adhesive.

7. Fit shelf into place ensuring it is correctly aligned with legs, mark the position of holes

for securing brackets on wall, remove shelf and drill wall and insert fixings in accordance

with Point 5, these brackets can be recessed if required. Fit the stub hearth in position

between the legs.

8. Ensure that the surround components as shown below in figure 8 are mechanically

secured as indicated, this is required in accordance with the latest revision of BS 1251 :

2015 Open Fireplace Components.

Fig. 8

9. Once the fireplace is correctly installed, grout all of the joints including between the

fireplace and the wall with a water based cream mastic or tile grout. Ensure all surplus

grout is immediately removed by washing the stonework using a sponge and clean

water.

Page 8 of 30

INSTA ING THE “BOTICE I” SURROUND

1. Unpack the surround from the wooden crate, check all parts are present as per below

and carefully store the components.

Contents of Boticelli surround:-

1 off hearth panel

1 off R/H leg

1 off L/H leg

1 off R/H infill section

1 off L/H infill section

1 off bottom infill section

1 off shelf top infill section

1 off shelf top section

1 off top infill section

1 off stub hearth

Fig. 9