Cervis Wireless Smart HH 10 Series Bedienungsanleitung

2019 Cervis, Inc.

HH-x10 Remote Control Unit Manual

DN: U089.1.1-SmaRT_HH-x10

™

SmaRT HH-x10

This document is the property of Cervis, Inc. and cannot be copied, modified, e-mailed, or

reproduced without the express prior written consent of Cervis, Inc.

Cervis, Inc. reserves the right to change this manual or edit, delete, or modify any information

without prior notification.

FCC Statements

15.19 –Two Part Warning

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference and

(2) This device must accept any interference received, including interference that may cause undesired operation.

15.21 –Unauthorized Modification

NOTICE: The manufacturer is not responsible for any unauthorized modifications to this equipment made by the user. Such modifications could

void the user’s authority to operate the equipment.

15.105(b) –Note:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Industry Canada Statement

This device complies with Canadian RSS-210.

The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits

for the general population; consult Safety Code 6, obtainable from Health Canada’s website https://www.canada.ca/en/health-

canada/services/environmental-workplace-health/reports-publications/radiation/safety-code-6-health-canada-radiofrequency-exposure-guidelines-

environmental-workplace-health-health-canada.html.

Le présent appareil est conforme à la norme CNR-210 d'Industrie Canada.

Le programme d’installation de cet équipement radio doit s’assurer que l’antenne est située ou fait telle qu’elle n’émet pas de champ RF dépassant les

limites de Santé Canada pour la population générale ; consulter le Code de sécurité 6, disponible auprès de Santé Canada site Web

https://www.canada.ca/en/health-canada/services/environmental-workplace-health/reports-publications/radiation/safety-code-6-health-canada-

radiofrequency-exposure-guidelines-environmental-workplace-health-health-canada.html.

Industry Canada Statement

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux

conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même

si le brouillage est susceptible d'en compromettre le fonctionnement.

RoHS Compliance Statement

Cervis, Inc. complies with the requirements of Restriction of Hazardous Substances (RoHS/WEEE) Specification based on in-house practice and

declaration of compliance from our vendors. For additional information concerning RoHS compliance, please contact Cervis, Inc. at:

CERVIS, Inc.

170 Thorn Hill Road Warrendale, PA 15086

Phone: 724.741.9000 Fax: 724.741.9001

This product may contain material that may be hazardous to human health and the environment. In

compliance with EU Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE):

Do not dispose of the product as unsorted municipal waste.

This product should be recycled in accordance with local regulations. Contact local

authorities for detailed information.



This product may be returnable to the distributor for recycling. Contact your distributor

for details.

Remote Control Unit Manual

2019 Cervis, Inc.

Notes/Definitions

Associate

SmaRT configuration method using a series of specific remote unit button presses to establish a

communication link between a SmaRT Remote Control Unit and a SmaRT Base Unit.

DSSS

Direct sequence spread spectrum; an advanced wireless communication technology.

Dissociate

Dissolution of established communication links between remote control units and base units

involved in the process.

Line of Sight (aka Direct-Line-of-Sight)

Type of communication between transceivers, or a transmitter and a receiver, where the

pathway between the two units must be clear of obstacles.

TX/RX

Transmit/Receive

Document Conventions



Note: Notes are used to indicate points of interest or pertinent information.

Cautions are used to warn of serious consequences of actions or inactions that

may result in injury, death, or serious damage to the equipment.

SmaRT HH-x10

U089.1.1-SmaRT_HH-x10

Table of Contents

Notes/Definitions ...........................................................................................................................i

Document Conventions ................................................................................................................i

Table of Contents .........................................................................................................................ii

List of Figures...............................................................................................................................ii

List of Tables.................................................................................................................................ii

Cervis, Inc. Safety Precautions...................................................................................................1

1.0 SmaRT HH-x10 Remote Control Unit..................................................................................2

2.0 Remote Control and Base Unit Communication ...............................................................4

2.1 Associate HH-xH10 Remote Control to Base Unit.........................................................4

2.2 Dissociate HH-xH10 Remote Control from Base Unit ...................................................5

3.0 Battery Installation or Change ............................................................................................6

4.0 Using a Standard SmaRT Remote Control ........................................................................7

5.0 Low Battery Warning and Low Battery Auto-Shutdown ..................................................8

6.0 Specifications .......................................................................................................................9

7.0 Spare Parts List ..................................................................................................................10

Appendix A: Exposure to Radio Frequency Energy...............................................................11

Appendix B: Agency Identification Label Locations ..............................................................11

List of Figures

Figure 1. HH-x10 6-LED Remote Control Button Assignments .................................................2

Figure 2. Standard Ten-Button Example......................................................................................3

Figure 3. Associate an HH-x10 Remote Control to a Base Unit.................................................4

Figure 4. Dissociate an HH-x10 Remote control from a Base Unit............................................5

Figure 5. Remote Control Battery Installation .............................................................................6

Figure 6. HH-x10 Front Panel.........................................................................................................7

Figure 7. HH-x10 Remote Low Battery Warning and Auto-Shutdown ......................................8

Figure 8. Agency Identification Label Locations...................................................................... 11

List of Tables

Table 1. HH-x10 Remote Control Options....................................................................................3

Table 2. SmaRT HH-x10 Remote Control Specifications............................................................9

Table 3. Spare Parts List............................................................................................................. 10

Remote Control Unit Manual

2019 Cervis, Inc.

Cervis, Inc. Safety Precautions

Read and follow all instructions.

Failure to abide by Safety Precautions may cause equipment failure, loss of authority

to operate the equipment, and personal injury.

Use and maintain proper wiring. Follow equipment manufacturer instructions.

Improper, loose, and frayed wiring can cause system failure, equipment damage, and

intermittent operation.

Equipment changes or modifications not expressly approved by the manufacturer will

void the warranty.

Equipment owner/operators must abide by all applicable Federal, State, and Local

laws concerning equipment installation and operation. Failure to comply could result

in penalties and could void user authority to operate the equipment.

Make sure that the machinery and surrounding area is clear before operating. Do not

activate the remote control system until you are certain that it is safe to do so.

Turn off the remote control and disconnect power from the base unit before

attempting any maintenance. This will prevent accidental operation of the controlled

machinery.

Power can safely be disconnected from the remote by removing the source power

(batteries) from the unit.

Power can be removed from the base unit by disconnecting the source power from

the circuit.

Use a damp cloth to keep units clean. Remove mud, concrete, dirt, etc. after use to

prevent obstructing or clogging the buttons, levers, wiring, and switches.

Do not allow liquid to enter the remote control or base unit enclosures. Do not use

high-pressure equipment to clean the remote control or base unit.

Disconnect the base unit before welding on the machine. Failure to disconnect the

base unit may cause destruction of or damage to the base unit.

Operate and store units only within the specified operation and storage temperatures

defined in this document’s Specifications.

SmaRT HH-x10

U089.1.1-SmaRT_HH-x10

1.0 SmaRT HH-x10 Remote Control Unit

Remote Control Features

License-free 900MHz or 2.4GHz Direct Sequence Spread Spectrum Technology (DSSS)

Direct-line-of-sight communications up to 1000 ft. (330m) range

Powered by two AAA cell batteries

Low Battery Warning and Low Battery Auto-Shutdown

Discrete ON and OFF buttons

Ten function buttons

Diagnostic light-emitting diode (LED) indicators

Rugged high-impact polymer enclosure; compact weatherproof design

Removable rubber bumper and detachable lanyard or belt clip

Operating temperature: -4°F to +131°F (-20°C to +55°C)

SmaRT wireless high-power HH-x10 remote control units communicate with and control SmaRT

base units operating in the 900MHz or 2.4GHz range. The HH-x10 remote control unit has

individual ON and OFF buttons and ten function control buttons. The remote control has an

automatic shutdown timeout–a period of time after which the remote turns itself off to conserve

power if no function buttons are pushed.

Figure 1. HH-x10 6-LED Remote Control Button Assignments

The HH-x10 remote control can communicate with a wide variety of SmaRT base units using

direct sequence spread spectrum (DSSS) wireless technology at 2.4GHz or 900MHz. A

standard HH-x10 offers up to ten command functions, and up to twenty command functions with

the dual use of the green button as both ON and SHIFT functions. It offers a robust link with a

base unit in congested radio environments. SmaRT remote control units feature seamless

association with SmaRT base units without needing to open either the remote control or base

unit cases.

The weatherproof remote control enclosure is made of rugged high-impact plastic with a face

plate securely sealed and attached by eight screws. It is further protected by a removable rubber

bumper that covers the unit’s back and sides. A lanyard that can be attached to the unit through

a recess on the bottom of the rubber bumper is available; or the unit can be ordered with a

convenient belt clip.

User Writable Label

Custom Text Label

Custom Label

(Example)

Remote Control Unit Manual

2019 Cervis, Inc.

Two size AAA cell batteries power the SmaRT HH-x10, and it operates between 2.0VDC to

3.2VDC. Six visible status/diagnostic LEDs (see Figure 2) indicate transmit (TX) and receive

(RX) activity, communications errors (ERR), and low battery (BAT) warning. Two additional

LEDs—A1 and A2—offer custom-programmed auxiliary status indications.

Figure 2. Standard Ten-Button Example

Notice in Figure 2 that the ten function pushbuttons are unassigned to specific SmaRT base unit

outputs. This allows for maximum flexibility while programming to interface with the wide array of

available SmaRT base units. An example of a custom programmed HH-x10 is shown as the

center unit in Figure 1.

HH-x10 Remote Control Remote Options

The HH-x10 can be ordered with or without a belt clip. Table 1 lists the available models.

Table 1. HH-x10 Remote control Options

Model Name

Frequency

RF Power

Activation,

Deactivation

Belt

Clip

HH-9H10

900MHz

10mW

ON,OFF

HH-9H10B

900MHz

10mW

ON,OFF

YES

HH-2H10

2.4GHz

100mW

ON,OFF

HH-2H10B

2.4GHz

100mW

ON,OFF

YES

HH-9X10

900MHz

100mW

ON,OFF

HH-9X10B

900MHz

100mW

ON,OFF

YES

OFF Button

ON Button

B1 through B10 are

FUNCTION Buttons

ASSOCIATE (button B1)

TX blinking Green when transmitting

RX blinking Amber when receiving

ERR blinking Red when error occurs

BAT blinking Amber when Low Battery

Protective Bumper

A1 (Auxiliary 1) Custom program use

A2 (Auxiliary 2) Custom program use

DISSOCIATE (button B2)

SmaRT HH-x10

U089.1.1-SmaRT_HH-x10

2.0 Remote Control and Base Unit Communication

2.1 Associate HH-xH10 Remote Control to Base Unit

An HH-x10 remote control unit must establish a communications link with a base unit before it

can be used for control. An HH-x10 remote (as part of a system) is associated with the system

base unit before leaving Cervis, Inc. But, it is possible to associate an HH-x10 in the field either

to address a communication problem or to add or replace a remote control unit. The procedure

to establish the link is called “Association”.

In situations where it is necessary to establish or re-establish remote control-to-base unit

communications, use the following steps:

HH-9H10/2H10 Models:

1. Stand near the base unit with the remote control OFF and power removed from

the base unit.

2. Push and hold the B1 and ON buttons. All six LEDs light solid.

3. Observe the LEDs. When only the TX LED begins to blink, power up the base

unit while continuing to hold B1 and ON.

4. When all six LEDs light solid, release both buttons.

HH-9X10 Models:

1. Stand near the base unit with the remote control OFF and power removed from

the base unit.

2. Push and hold the B1 and ON buttons for approximately two seconds. The A1,

A2, and TX LEDs light. Release the B1 and ON buttons.

3. Press and hold button B1. Turn base unit power on. Release button B1 when

base unit powers up.

The remote control and base unit are connected when both the TX and RX LEDs on both

devices start blinking simultaneously as messages pass between them.The SmaRT system is

ready for use.

Figure 3. Associate an HH-x10 Remote Control to a Base Unit

Hold to ASSOCIATE

Hold to

ASSOCIATE

BAT

ERR

Remote Control Unit Manual

2019 Cervis, Inc.

2.2 Dissociate HH-xH10 Remote Control from Base Unit

In some circumstances, it may become necessary to break the communication link, or

“dissociate”a remote control and a base unit. The dissociate procedure is almost identical to the

associate procedure, except the dissociate button (B2) is used and held throughout the process

instead of the Associate button (B1).

Using the following steps will break all previously established remote

control links.

HH-9H10/2H10 Models:

1. Stand near the base unit with the remote control OFF and power removed from

the base unit.

2. Push and hold B2 and the ON button. All six LEDs light solid.

3. Observe the LEDs. When only the TX LED begins to blink, power up the base

unit while continuing to hold B2 and ON.

4. When all six LEDs light solid, release both buttons.

HH-9X10 Models:

1. Stand near the base unit with the remote control OFF and power removed from

the base unit.

2. Push and hold the B2 and ON buttons for approximately two seconds. The A1,

A2, and TX LEDs light. Release buttons B2 and ON.

3. Press and hold button B2. Turn base unit power on. Release button B2 when

base unit powers up.

4. Remote control and base unit are disconnected when the TX LED (only) starts

blinking.

Established links with base units are removed. To re-establish a communication link with a base

unit, use the Associate Procedure (Section 2.1).

Figure 4. Dissociate an HH-x10 Remote control from a Base Unit

Hold to DISSOCIATE

Hold to

DISSOCIATE

BAT

ERR

SmaRT HH-x10

U089.1.1-SmaRT_HH-x10

3.0 Battery Installation or Change

Two size AAA cell batteries power SmaRT HH-x10 remote control units. When installing

batteries, be sure to observe proper polarity—as marked on the inside of the compartment—to

avoid damaging the unit.

To replace or install remote control batteries:

1. Loosen the four small Phillips screws on the battery compartment cover, and lift

the cover from the remote control. The screws remain attached to the cover.

2. If installing batteries in an empty battery compartment, install two fresh size AAA

cell batteries. Be sure to position the batteries as illustrated in Figure 5 below.

3. If replacing expired batteries, remove the old batteries, and install two fresh size

AAA cell batteries. (Discard the used batteries according to local regulations.) Be

sure to position the batteries as illustrated in Figure 5 below.

4. Replace the compartment cover and tighten the four Phillips screws. Do not over-

tighten these screws, but make sure they are tight enough to properly seal the

gasket.



Note: Discard expired batteries according to local regulations.

Figure 5. Remote Control Battery Installation



Note: Cover screws must be tight enough to compress the sealing gasket. Do not over-

tighten the screws.

Be sure to observe proper polarity when placing batteries in

the remote control battery compartment.

Sealing gasket

Cover

screws

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cervis Steuereinheit Handbücher

Cervis

Cervis MRF450 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung