CHAINTECH 7VJL1 Bedienungsanleitung

CHAINTECH

7VJL1

AMD® Socket A

VIA® KT266A + VT8235

ATX Motherboard

User’s Manual

Ve r s i o n 1 . 0

Declaration of Conformity

According to 47 CFR, Parts 2 and 15 of the FCC Rules

The following designated product:

EQUIPMENT: MAINBOARD

MODEL NO.: 7VJL1

is a Class B digital device that complies with 47 CFR Parts 2 and 15 of the FCC

Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that

may cause undesired operation.

This declaration is given to the manufacturer:

CHAINTECH-EXCEL COMPUTER INC.

4427 Enterprise St. Fremont, CA 94538, U.S.A.

http://www.chaintech-excel.com

Chaintech President: Simon Ho

Signature:

Federal Communications Commission Statement

This device complies with FCC Rules Part 15. Operation is subject to the following two conditions:

* This device may not cause harmful interference.

* This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If this

equipment is not installed and used in accordance with the manufacturer's instructions, it may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

* Reorient or relocate the receiving antenna.

* Increase the separation between the equipment and receiver.

* Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

* Consult the dealer or an experienced radio/TV technician for help.

The use of shielded cables for connection of the monitor to the graphics card is required to assure

compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user's authority to operate this equipment.

Canadian Department of Communications Statement

This digital apparatus does not exceed the Class B limits for audio noise emissions from digital apparatuses

set out in the Radio Interference Regulations of the Canadian Department of Communications.

Manufacturer's Disclaimer Statement

The information in this document is subject to change without notice and does not represent a commitment

on the part of the vendor. No warranty or representation, either expressed or implied, is made with respect to the

quality, accuracy or fitness for any particular purpose of this document. The manufacturer reserves the right to

make changes to the content of this document and/or the products associated with it at any time without obligation

to notify any person or organization of such changes. In no event will the manufacturer be liable for direct, indirect,

special, incidental or consequential damages arising out of the use or inability to use this product or documentation,

even if advised of the possibility of such damages. This document contains materials protected by copyright. All

rights are reserved. No part of this manual may be reproduced or transmitted in any form, by any means or for any

purpose without expressed written consent of it's authors. Product names appearing in this document are mentioned

for identification purposes only. All trademarks, product names or brand names appearing in this document are

registered property of their respective owners.

Printed in Taiwan.

Oct 2002

OST-CONSUMER

RECYCLED PAPER

100%

TABLE OF CONTENTS

Chapter 1 Introduction ............................................................. 1

1-1 Product Specifications .....................................................................................1

1-2 Package Contents.............................................................................................2

1-3 7VJL1 Motherboard Diagram .........................................................................3

1-4 7VJL1 Motherboard Layout ............................................................................ 4

Chapter 2 Hardware Setup....................................................... 5

2-1 Installing a CPU Processor for Socket A.........................................................5

2-2 Setting Your CPU’s Performance: ................................................................... 6

2-3 Main Memory Configuration...........................................................................8

2-4 Connector and Jumper Reference Chart........................................................10

2-5 Connector and Jumper Settings ..................................................................... 11

Chapter 3 BIOS Setup Program ............................................23

3-1 Standard CMOS Setup...................................................................................24

3-2 Advanced BIOS Features ..............................................................................25

3-3 Advanced Chipset Features ...........................................................................28

3-4 Integrated Peripherals ....................................................................................30

3-5 Power Management Setup .............................................................................34

3-6 PNP/PCI Configurations................................................................................37

3-7 PC Health Status ............................................................................................ 38

3-8 Frequency/Voltage Control ............................................................................39

3-9 Load Fail-Safe Defaults.................................................................................42

3-10 Load Optimized Defaults.............................................................................42

3-11 Supervisor Password & User Password Setting

...................................................42

3-12 Save and Exit Setup ..................................................................................... 43

3-13 Exit Without Saving .................................................................................... 43

Chapter 4 DRIVER Setup.......................................................44

4-1 VIA Service Pack .......................................................................................... 44

4-2 Audio driver...................................................................................................48

4-3 USB 2.0 Driver ..............................................................................................50

How To Contact CHAINTECH..............................................54

Chapter 1

Chapter 1 Introduction

1-1 Product Specifications

Processor

- Supports AMD Socket A Duron / Athlon / XP processors.

- System Clock supports 200 / 266 MHz Front Side Bus

Chipset

- VIA® KT266A + VT8235 Chipset.

Main Memory

- Supports three 184-pin DDR DIMM sockets up to 3GB.

- Supports PC1600/DDR200 PC2100/DDR266 DDR SDRAM modules.

Expansion Slots

- One Universal - AGP slot for both 2X / 4X AGP (V2.0 compliant).

- Six 32 - bit PCI slots (v 2.2 compliant).

Audio subsystem via AC-Link

- With external high quality AC'97 Codec

- Complete software driver supports for Windows® OS

Embedded Ultra DMA - 133 PCI IDE controller

- Supports two IDE ports up to 4 ATAPI devices

- Supports up to PIO Mode 4 up to 16.6MBps, Multi Mode 4 up to 66MBps, Multi

Word Mode 5 up to 100MBps and Multi Word Mode 6 up to 133MBps with bus

mastering

- Bus Mastering software drivers for common multi-task operating systems

Embedded USB 2.0/1.0 Host Controller

- UHCI compliant USB host controller with Root hub

- Six USB ports (EHCI/UHCI v1.1 compliant) with over current protection.

- Optional USB adapter for additional USB2.0/1.1 ports

On board ITE 8705 Super I/O Controller

- Two UARTs support serial port s and IR function (up to 115.2Kbps) for HPSIR

and ASKIR

- One SPP/ECP/EPP parallel port

- One floppy disk drive connector supports up to 2.88MB

- Integrates smart card reader function and interface, to be qualified for meeting

PC/SC standard

Chapter 1

Embedded System Monitor Hardware

- 8 external voltage inputs

- 2 temperature sensor with thermistor for CPU and System

- 2 Fan speed monitoring with ON/OFF control in suspend

Ethernet 10/100 Controller

- On board PHY LAN VIA® VT6103 support 10/100Mbs operation

Boot-Block Flash ROM

- Award system BIOS support PnP, APM, DMI, ACPI, & Multi-device booting

features.

1-2 Package Contents

This product comes with the following components:

1. Motherboard x 1

2. 40-Pin UDMA-100 IDE Cable x 1

Blue to motherboard, Gray to Master and Black to Slave.

3. 34-Pin floppy Disk Drive Cable x 1

4. Manual x 1

5.DriverCD x1

Includes:

- Award DMI Utility for DOS

- Audio drives and utility

- LAN Drivers

- USB 2.0 Drivers

- VIA® Chipset Software installation utility.

6. Value-pack 2002 x 1

Includes:

- Norton AntiVirus

- Adobe ActiveShare

- AcobarReader

- Acobate eBook Reader

- Imagemore

- AutoSave.

Chapter 1

1-3 7VJL1 Motherboard Diagram

Chapter 1

1-4 7VJL1 Motherboard Layout

Chapter 2

Chapter 2 Hardware Setup

If your motherboard has already been installed in your computer you may still need

to refer to this chapter if you plan to upgrade your system's hardware.

This motherboard is electrostatic sensitive. Do not touch without

wearing proper safety gadget and make sure to disconnect the power

cable from the power source before performing any work on your

motherboard. Not doing so may result in electrical shock!

2-1 Installing a CPU Processor for Socket A

The Socket A, designed for AMD® Athlon/Duron/XP processors, has been

incorporated as a standard motherboard specification. To insert your CPU into

Socket A please do the following:

1. Locate a cut edge on the top surface of the CPU close to one if it's corners. The

same corner will also be cut off, leaving a noticeable notch in the CPU's corner.

These markings indicate Pin 1 of the CPU.

2. Pull up the lever of Socket 462 so that it is perpendicular with the surface of the

motherboard. Gently insert the CPU with Pin 1 at the same corner of Socket 462

that contains the end of the lever. Allow the weight of the CPU to push itself into

place. Do not apply extra pressure as doing so may result in damaging your CPU.

Snap the lever back into place.

Installing an AMD® approved heat sink with cooling fan is necessary for

proper heat dissipation from your CPU. Failing to install these items may

result in overheating and possible burn-out of your CPU.

In order to boot up with a newly installed CPU, AC Power must be

switched off before installation.

Chapter 2

2-2 Setting Your CPU’s Performance:

Frequency Configuration:

If you install a CPU on this motherboard, you must set the [Front Side Bus

Frequency] JP3 according to your processor (See Section 2.4).

* CPU Speed = Multiplier x FSB Frequency

AMD (K7) Duron CPU

Model CPU Speed FSB

Frequency Multiplier Vcore L2

Cache

Micron

process

600 600 MHz 100 6.0 1.6V 64KB 0.18

650 650 MHz 100 6.5 1.6V 64KB 0.18

700 700 MHz 100 7.0 1.6V 64KB 0.18

750 750 MHz 100 7.5 1.6V 64KB 0.18

800 800 MHz 100 8.0 1.6V 64KB 0.18

850 850 MHz 100 8.5 1.6V 64KB 0.18

900 900 MHz 100 9.0 1.6V 64KB 0.18

950 950 MHz 100 9.5 1.6V 64KB 0.18

1.0G 1.0 GHz 100 10.0 1.6V 64KB 0.18

1.1G 1.1 GHz 100 11.0 1.6V 64KB 0.18

1.2G 1.2 GHz 100 12.0 1.6V 64KB 0.18

1.3G 1.3 GHz 100 13.0 1.6V 64KB 0.18

You do not need to make voltage settings because this board will automatically

set your CPU voltage.

Chapter 2

AMD Athlon CPU (K7/Thunderbird)

Model CPU Speed FSB

Frequency Multiplier

core L2

Cache

Micron

process

700 700MHz 100 7.0 1.70V 256KB 0.18

750 750MHz 100 7.5 1.70V 256KB 0.18

800 800MHz 100 8.0 1.70V 256KB 0.18

850 850MHz 100 8.5 1.70V 256KB 0.18

900 900MHz 100 9.0 1.75V 256KB 0.18

950 950MHz 100 9.5 1.75V 256KB 0.18

1000 1000MHz 100 10.0 1.75V 256KB 0.18

1100 1100MHz 100 11.0 1.75V 256KB 0.18

1200 1200MHz 100 12.0 1.75V 256KB 0.18

1300 1300MHz 100 13.0 1.75V 256KB 0.18

1400 1400MHz 100 14.0 1.75V 256KB 0.18

1000 1000MHz 133 7.5 1.75V 256KB 0.18

1113 1113MHz 133 8.5 1.75V 256KB 0.18

1200 1200MHz 133 9.0 1.75V 256KB 0.18

1333 1333MHz 133 10.0 1.75V 256KB 0.18

1400 1400MHz 133 10.5 1.75V 256KB 0.18

AMD Athlon XP CPU (Palomino/Thunderbird)

Model CPU

Speed

FSB

Frequency Multiplier Vcore L2

Cache

Micron

process

1500+ 1333MHz 133 10.0 1.7V 256KB 0.18

1600+ 1400MHz 133 10.5 1.7V 256KB 0.18

1700+ 1467MHz 133 11.0 1.7/1.6V 256KB 0.18/0.13

1800+ 1500MHz 133 11.5 1.7/1.6V 256KB 0.18/0.13

1900+ 1600MHz 133 12.0 1.7/1.6V 256KB 0.18/0.13

2000+ 1666MHz 133 12.5 1.7/1.6V 256KB 0.18/0.13

2100+ 1733MHz 133 13.0 1.7/1.6V 256KB 0.18/0.13

2200+ 1800MHz 133 13.5 1.65V 256KB 0.13

2400+ 1995MHz 133 15.0 1.65V 256KB 0.13

2600+ 2128MHz 133 16.0 1.65V 256KB 0.13

Chapter 2

2-3 Main Memory Configuration

This motherboards provides 3 184pin Double Data Rate (DDR) Dual Inline Memory

Modules (DIMM) slots. Which supports PC 1600/DDR200 or PC2100/DDR266

DDR SDRAM modules up to 3GB. Install at least one DIMM module on the slots.

Memory modules can be installed on the slots in any order. You can install either

single- or double-sided modules to meet your own needs. The DDR SDRAM

memory system consists three banks and each bank can support up to 1GB memory

size. If you only use one bank it does not matter which one you use and if you use

two or more banks, it does not matter which bank you install first.

DRAM Specifications

DIMM type: 2.5V unbuffered 64/128/256/512-bit DDR SDRAM.

Module size: Single/double-sided 64/128/256/512MB/1GB.

Parity: Ether parity or non-parity.

Chapter 2

DIMM Module Combination

Install at least one DIMM module on the slots. You can install either single- or

double-sided modules in any order to meet your own needs. Memory modules can

be installed in any combination as follows:

Location 64 MB 128 MB 256 MB 512 MB 1.0 GB

DDR 1 X X X X X

DDR 2 X X X X X

DDR 3 X X X X X

To install your DDR Modules please follow the following steps:

1. Unlock a DIMM socket by pressing the retaining clips outward. The DDR

Modules has only one notch at the center of module. The DDR module will only

fit in the right position.

2. Insert the DDR Module vertically into the DIMM slot, with the correct alignment.

Then push it in until the golden finger on the memory module is deeply inserted

into the socket.

3. The plastic clip on each side of the DIMM slot will automatically close to hold the

DDR Modules in place.

Chapter 2

2-4 Connector and Jumper Reference Chart

Jump Connector Function Page

PW 1/2 ATX Power Supply Connector 11

FD1 Floppy Connector 12

IDE 1/2 IDE Hard-Disk Connector 13

FAN 1/2/3 CPU/ System / Case FAN Connector (12V) 13

JP1 CMOS Clear Jumper 14

JP3 CPU Front Side Bus setting 14

JP5 Keyboard Power on Function Jumper 15

JP6 Disable/Enable USB 0/1 Device Power ON Jumper 15

JP6A /B Disable/Enable USB 2/3,4/5 Device Power ON Jumper 16

JP23 Green LED Mode Jumper 16

JP30 ROM SIP 17

CN1A Front Panel (Power / Rest / SPK…etc.) Connector 17

CN2 /2A CD-ROM Audio-in Connector 18

CN3 Auxiliary Audio-in Connector 19

CN5 Wake on LAN Connector 19

CN5A Wake on Modem Connector 20

CN7 Smart Card Reader Connector 20

CN17 Blue LED Connector (5V) 21

CN23 /23A USB Connector for USB 2/3 and 4/5 21

CN24 Front Audio Connector 22

IR1 IR Connector 22

Chapter 2

2-5 Connector and Jumper Settings

Connectors are used to link the system board with other parts of the system,

including the power supply, the keyboard, and the various controllers on the front

panel of the system case.

The power supply connector is the last connection to be made while

installing a motherboard. Before connecting the power supply, please make

sure it is not connected to the power source.

All cables are security-proof

PW 1 / 2 (ATX Power Supply Connector):

The power cord leading from the system's power supply to the external power

source must be the very last part connected when assembling a system. The ATX

power supply provides a single 20-pin connector interface, which incorporates

standard +/-5V, +/-12V, optional 3.3V and Soft-power signals. The Soft-power

signal, a 5V trickle supply is continuously supplied when AC power is available.

When the system is in the Soft-Off mode, this trickle supply maintains the system in

it's minimum power state.

Software Power-Off Control

This motherboard can be powered down using Windows® 9x Software Power-Off

function. To power down your computer, click the START button on the Windows®

9x task bar. Select “Shut down the computer” and the system turns off. The message

“It is now safe to turn off your computer” will not be shown when using this

function.

Chapter 2

Power-On By Modem:

While in Soft-Off state, if an external modem ring-up signal occurs, the system

wakes up and can be remotely accessed. You may enable this function in BIOS's

Power Management Setup menu. (See section 3).

Blinking LED in Suspend Mode:

While in Suspend mode, the LED light on the front panel of your computer will

flash. Suspend mode is entered by pressing the Override Power Button, pushing the

Green button on your ATX case, or enabling the Power Management and Suspend

Mode options in BIOS's Power Management menu. (See section 3).

Poly-fuse Over Current Protection:

The poly-fuse protects the system from dangerous voltages that the system might be

exposed to via the keyboard or USB connector. In case of such exposure, the

poly-fuse will immediately be disconnected from the circuit, just like a normal fuse.

After being disconnected for a certain period of time, the poly-fuse will return to its

normal state. Then the keyboard or USB connector can function properly again.

Unlike conventional fuses, the poly-fuse does not have to be replaced, relieving the

user wasted time and inconvenience.

FD1 (Floppy Connector)

This motherboard provides a standard floppy disk drive connector that supports

360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector is used to

connect 34 pins of Floppy drive cable.

Chapter 2

IDE 1/2 (IDE Hard-Disk Connector)

This connector is used for connecting 40 pins of ATAPI devices.

IDE 1 only connects two IDE devices. (Primary Master/Slave)

IDE 2 only connects two IDE devices. (Secondary Master/Slave)

FAN1/FAN2/FAN3 (CPU/System/Case Cooling Fan Connectors [12V]):

The board's management extension hardware is able to detect the CPU and system

fan speed in rpm (revolutions per minute). The wiring and plug may vary depending

on the manufacturer. On standard fans, the red is positive (+12V), the black is

ground, and the yellow wire is the rotation signal.

Chapter 2

JP1 (CMOS Clear Jumper):

There is a CMOS RAM on board that has a power supply from external battery to

keep the data and system configuration. To clear the contents of the CMOS, please

follow the steps below.

1. Disconnect the system power supply from the power source.

2. Set the jumper cap at location [2-3] for <5 seconds>, and then set it back to the

default position.

3. Connect the system's power and then start the system.

4. Enter BIOS's CMOS Setup Utility and choose Load Setup Defaults. Type [Y] and

then press [Enter] to continue.

5. Set the system configuration in the Standard CMOS Setup menu.

JP3 (CPU Front Side Bus setting)

This function allows you to set the CPU’s Front Side Bus, the default setting is at

pin [1-2], which is FSB 100MHz. Set the cap at [2-3] to force the FSB at 133 MHz.

Pin Definition

1-2 Normal (default)

2-3 Clear CMOS Data

Pin Definition

1-2 FSB 100 MHz

2-3 FSB 133 MHz

Chapter 2

JP5 (Keyboard Power On Function Jumper):

This board can be turned on by the PS / 2 keyboard (hot key). To use this function,

select a hot key of your choice at the PS2KB Wakeup option under Wake Up Events

in the BIOS's Power On Management screen. You must also set this jumper's cap to

pins 2-3 to use this function.

JP6 (Enable/Disable USB 0/1 Device Power ON Jumper)

This motherboard is can be turned on by a USB keyboard hot key or a USB mouse

click. To use this function, select a hot key of your choice at the USB KB Power

Wake-up From S3 option under Wake Up Events in the BIOS's Power On

Management screen. You must also set this jumper's cap to pins 2-3 to use this

function.

Pin Definition

1-2 Disable (default)

2-3 Enable

Pin Definition

1-2 Disable (default)

2-3 Enable

Chapter 2

JP6A/B (Enable/Disable USB 0/1, 2/3 Device Power ON Jumper)

This motherboard is can be turned on by a USB keyboard hot key or a USB mouse

click. To use this function, select a hot key of your choice at the USB KB Power

Wake-up From S3 option under Wake Up Events in the BIOS's Power On

Management screen. You must also set this jumper's cap to pins 2-3 to use this

function.

JP23 (Green LED Mode Jumper):

This motherboard provides a Green LED flash Jumper. This cap is to setup Green

LED flash mode.

Pin Definition

1-2 Disable (default)

2-3 Enable

Pin Definition

1-2 Normal (default)

2-3 Reserve

Inhaltsverzeichnis

Andere CHAINTECH Hauptplatine Handbücher

CHAINTECH

CHAINTECH CT-6AIA2 Bedienungsanleitung

CHAINTECH

CHAINTECH 7NIL1 Bedienungsanleitung

CHAINTECH

CHAINTECH P4M266A Bedienungsanleitung

CHAINTECH

CHAINTECH 5TDM2 Bedienungsanleitung

CHAINTECH

CHAINTECH 7VIL4 Bedienungsanleitung

CHAINTECH

CHAINTECH 6OIA3T Bedienungsanleitung

CHAINTECH

CHAINTECH 9BJD Bedienungsanleitung

CHAINTECH

CHAINTECH 6OIV Bedienungsanleitung

CHAINTECH

CHAINTECH 7VJS Bedienungsanleitung

CHAINTECH

CHAINTECH 6OJA3 Bedienungsanleitung

CHAINTECH

CHAINTECH 7SJD Bedienungsanleitung

CHAINTECH

CHAINTECH 7VIA1 Bedienungsanleitung

CHAINTECH

CHAINTECH 9BJD0 Bedienungsanleitung

CHAINTECH

CHAINTECH 7VJL5 Bedienungsanleitung

CHAINTECH

CHAINTECH 7VJDA Bedienungsanleitung

CHAINTECH

CHAINTECH 9BJA Bedienungsanleitung

CHAINTECH

CHAINTECH CT-6OJV3T Bedienungsanleitung

CHAINTECH

CHAINTECH 6WIFI Bedienungsanleitung

CHAINTECH

CHAINTECH 6VIA4 Bedienungsanleitung

CHAINTECH

CHAINTECH 7VIL3 Bedienungsanleitung

CHAINTECH

CHAINTECH 6AJA4 Bedienungsanleitung

CHAINTECH

CHAINTECH S1689 Bedienungsanleitung

CHAINTECH

CHAINTECH CT- 6AIA Bedienungsanleitung

CHAINTECH

CHAINTECH 6AIV Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung